Theoretical estimation of dielectric loss of oxide glasses using nonequilibrium molecular dynamics simulations

To theoretically explore amorphous materials with a sufficiently low dielectric loss, which are essential for next-generation communication devices, the applicability of a nonequilibrium molecular dynamics simulation employing an external alternating electric field was examined using alkaline silicate glass models. In this method, the dielectric loss is directly evaluated as the phase shift of the dipole moment from the applied electric field. This method enabled us to evaluate the dielectric loss in a wide frequency range from 1 GHz to 10 THz. It was observed that the dielectric loss reaches its maximum at a few THz. The simulation method was found to qualitatively reproduce the effects of alkaline content and alkaline type on the dielectric loss. Furthermore, it reasonably reproduced the effect of mixed alkalines on the dielectric loss, which was observed in our experiments on sodium and/or potassium silicate glasses. Alkaline mixing was thus found to reduce the dielectric loss.     

Fracture toughness evaluation of adjacent flow weld line in polystyrene by the SENB method

Fracture toughness of adjacent flow weld lines, defined as weld lines that occur when two flow fronts meet and continue to flow together in the same direction (meld line or hot weld line), was evaluated by the single‐edge notched‐bend (SENB) method using three differently‐shaped obstructive pins. Although the fracture toughness varied depending upon the shapes of the pin, the values could be standardized as the distance from the meeting point of the two flow fronts flowing around the pin. The fracture toughness decreased drastically from the meeting point along the weld line and then slightly increased. These characteristic features could be explained by flow‐induced molecular orientation at the weld line interface. The molecules around the meeting point that were initially oriented parallel to the weld line due to fountain flow were able to relax, and then entanglement across the weld line interface developed because the flow stopped in the middle of the filling process, resulting in high fracture toughness. In contrast, the material at the downstream side of the weld line continued flowing during the filling process, being stretched along the flow direction. So, the molecular orientation at this area could not relax. In addition, the V‐notch shape, i.e., the depth and length at the surface of the weld line, which also varied depending on the shape of the obstacles, was considered to be identical when the meeting point was allowed to be a datum point. Thus, the meeting point was found to be a significant factor when the properties of weld lines are investigated. POLYM. ENG. SCI., 45:1059–1066, 2005. © 2005 Society of Plastics Engineers     

Theoretical model for flash generation

Reduction of flash generated in a gas vent is of great concern for manufacturers of electronic parts. The present study proposes a theoretical model for flash generation through consideration of flow characteristics in a gas vent. The model predicts the factors controlling flash, i.e., material parameters such as zero‐shear viscosity, crystallization temperature, thermal conductivity, and heat capacity, and process parameters such as injection and mold wall temperatures, packing pressure, and the clearance of a gas vent. On the other hand, we measure the amount of flash generated in the molding of poly(phenylene sulfide) (PPS) composites containing glass fiber and spherical fillers (CaCO₃ or Al₂O₃). Flash reduces with decreasing size of spherical fillers. These experimental data are successfully interpreted using the flash model. Polym. Eng. Sci., 45:198–206, 2005. © 2005 Society of Plastics Engineers     

A flow simulation for the epoxy casting process using a 3D finite‐element method

A three‐dimensional flow simulation for epoxy casting has been developed. A control‐volume‐based finite‐element method is employed, containing a conservative upwind formulation for the advection terms and equal order interpolations for all variables. This simulation predicts the non‐isothermal and reactive flow behavior under the gravity. The viscosity and reaction‐rate parameters were estimated by using a dynamic rheometer and a differential scanning calorimeter. The predicted flow front advancement and temperature profiles in the calculation domain similar to the mold cavity were in close agreement with the corresponding experimental results. The variation of epoxy surface configuration with flow rate also showed the same tendency between the prediction and the experiment. This simulation seems to be applicable not only to the epoxy casting, but also to other molding processes of various thermoset resins. POLYM. ENG. SCI. 45:364–374, 2005. © 2005 Society of Plastics Engineers.     

Characterization and electrochemical properties of CF4 plasma-treated boron-doped diamond surfaces

The effect of CF₄ plasma etching on diamond surfaces, with respect to treatment time, was investigated using scanning electron microscopy (SEM), Raman spectroscopy, X-ray photoelectron spectroscopy (XPS), and electrochemical measurements. SEM observations and Raman spectra indicated an increase in surface roughening on a scale of 10–20 nm, and an increase in crystal defect density was apparent with treatment time in the range of 10 s to 30 min. In contrast, alteration of the diamond surface terminations from oxygen to fluorine was found to be rather rapid, with saturation of the F/C atomic ratio estimated from XPS analysis after treatment durations of 1 min and more. The redox kinetics of Fe(CN)₆^3−/4− was also found to be significantly modified after 10 s of CF₄ plasma treatment. This behavior shows that C–F terminations predominantly affect the redox kinetics compared to the effect on the surface roughness and crystal defects. The double-layer capacitance (C_dl) of the electrolyte/CF₄ plasma-treated boron-doped diamond interface was found to show a minimum value at 1 min of treatment. These results indicate that a short-duration CF₄ plasma treatment is effective for the fabrication of fluorine-terminated diamond surfaces without undesirable surface damage.     

Critical heat flux on a flat plate heater located at the middle of a duct in forced flow of pressurized He II

Critical heat fluxes (CHFs) were measured for two types of rectangular ducts containing horizontal flat plate heaters. One has the flat plate heater of 6 mm wide and 20 mm long located on the inner lower wall at 50 mm from the inlet. The other duct has two horizontal flat plates of 6 mm wide and 20 mm long on inner upper and lower walls at 50 mm from the inlet. The equation of CHF for the forced convection containing a new nondimensional-parameter m introduced in order to calculate cross-sectionally averaged liquid temperature at the center of the duct was derived based on two fluid model, ordinary convection theorem and experimental results. It was confirmed that this correlation can describe not only the author's data on the duct but also other worker's data for channels with different shapes and sizes.     

Rapid detection cytomegalovirus pneumonia in recipients of bone marrow transplant: evaluation and comparison of five survey methods for bronchoalveolar lavage fluid

To detect cytomegalovirus-associated interstitial pneumonia (CMV-IP) in recipients of BMT in its earliest stage, five CMV methods were assessed for their usefulness using bronchoalveolar lavage fluid as the test specimen. Of the 43 cases enrolled in the study, PCR was positive in 12 cases, shell vial in eight, culture in eight and cytology in three. There were no positive cases in in situ hybridization. Based on this result, the 43 cases were classified into four groups: Group 1, three cases: positive in PCR, shell vial and cytology; Group 2, five cases: positive in PCR and shell vial; Group 3, four cases: positive only in PCR; and Group 4, 31 cases: negative in all CMV tests. Cases in Group 1 were judged as having the highest risk of overt CMV-IP. They were successfully treated with a combination of ganciclovir and immunoglobulin. Group 2 was diagnosed as having active CMV infection and ganciclovir monotherapy was effective for these patients. Groups 3 and 4 were not given anti-CMV therapy, but they were free from CMV-related manifestations throughout the study. The sensitivity and specificity of each survey method for the detection of Groups 1 and 2 were 1.0 and 0.89 in PCR, 1.0 and 1.0 in shell vial, 0.88 and 1.0 in culture, and 0.38 and 1.0 in cytology. Similarly, the positive and negative predictive values were 0.67 and 1.0 in PCR, 1.0 and 1.0 in shell vial, 1.0 and 0.97 in culture, and 1.0 and 0.88 in cytology. Thus, CMV survey on bronchoalveolar fluid was thought to be useful in detecting post BMT CMV-IP in its earliest stage.