Transient liquid phase sintering of high-purity mullite for high-temperature structural ceramics

High-purity mullite ceramics, promising engineering ceramics for high-temperature applications, were fabricated using transient liquid phase sintering to improve their high-temperature mechanical properties. Small amounts of ultrafine alumina or silica powders were uniformly mixed with the mullite precursor depending on the silica-alumina ratio of the resulting ceramics to allow for the formation of a transient liquid phase during sintering, thus, enhancing densification at the early stage of sintering and mullite formation by the reaction between additional alumina and the residual glassy phase (mullitization) at the final stage of sintering. The addition of alumina powder to the silica-rich mullite precursor resulted in a reaction between the glassy silica and alumina phases during sintering, thereby forming a mullite phase without inhibiting densification. The addition of fine silica powder to the mullite single-phase precursor led to densification with an abnormal grain growth of mullite, whereas some of the added silica remained as a glassy phase after sintering. The resulting mullite ceramics prepared using different powder compositions showed different sintering behaviors, depending on the amount of alumina added. Upon selecting an optimum process and the amount of alumina to be added, the pure mullite ceramics obtained via transient liquid phase sintering exhibited high density (approximately 99%) and excellent high-temperature flexural strength (approximately 320 MPa) at 1500 °C in air. These results clearly demonstrate that pure mullite ceramics fabricated via transient liquid phase sintering with compositions close to those of stoichiometric mullite could be a promising process for the fabrication of high-temperature structural ceramics used in an ambient atmosphere. The transient liquid phase sintering process proposed in this study could be a powerful processing tool that allows for the preparation of superior high-temperature structural ceramics used in the ambient processing atmosphere.     

Systematic packaging design tools integrating functional and environmental consequences on product life cycle: Case studies on laundry detergent and milk

This study presents systematic packaging design tools integrating functional and environmental consequences on product life cycle. To design packaging for sustainability, the trade-offs between functional and environmental aspects of packaging throughout the product life cycle should be considered. However, it is difficult for packaging designers to understand the overall trade-offs because the extent of the design consequences on the entire life cycle of packaging and its contents is unclear. We developed two tools for packaging design: the Life Cycle Association Matrix (LCAM) and the Function Network Diagram (FND). The following three steps, based on literature reviews and interviews with industrial experts, were applied. Firstly, we listed the product functions and design variables related to the functions as the attributes allocated to the product life cycle. Secondly, the attributes were connected appropriately based on causal relationships. Lastly, we identified the factors to support decision making in the packaging design procedure. As a result, the LCAM depicts the design consequences on the life cycle, and the FND determines the stakeholders affected by the design consequences. Two case studies were demonstrated to analyze the trade-offs by using our tools. In the case studies, a liquid laundry detergent bottle and a milk carton were redesigned. The tools identified the design consequences and stakeholders affected by the redesign of the usability and protective function for the detergent and milk cases, respectively. The results showed the significance of understanding the design consequences on the product life cycle by integrating the functional and environmental aspects.     

A pseudoaneurysm after repair of thoraco-abdominal aortic aneurysm

We report a 63-year-old female patient developing a pseudoaneurysm three years after patch-plasty of an aneurysm located at the distal thoracic aorta. Redo-operation was performed including total replacement of the descending thoracic aorta with reimplantation of distal intercostal arteries using small-caliber interposition grafts. This case presentation underlines the ineffectiveness of patch repair for the treatment of aortic aneurysms. Furthermore, the surgical technique of reimplantation of intercostal arteries using a separate graft is discussed.     

Pool boiling on a superhydrophilic surface

Titanium Dioxide, TiO₂, is a photocatalyst with a unique characteristic. A surface coated with TiO₂ exhibits an extremely high affinity for water when exposed to UV light and the contact angle decreases nearly to zero. Inversely, the contact angle increases when the surface is shielded from UV. This superhydrophilic nature gives a self-cleaning effect to the coated surface and has already been applied to some construction materials, car coatings and so on. We applied this property to the enhancement of boiling heat transfer. An experiment involving the pool boiling of pure water has been performed to make clear the effect of high wettability on heat transfer characteristics. The heat transfer surface is a vertical copper cylinder of 17 mm in diameter and the measurement has been done at saturated temperature and in a steady state. Both TiO₂-coated and non-coated surfaces were used for comparison. In the case of the TiO₂-coated surface, it is exposed to UV light for a few hours before experiment and it is found that the maximum heat flux (CHF) is about two times larger than that of the uncoated surface. The temperature at minimum heat flux (MHF) for the superhydrophilic surface is higher by 100 K than that for the normal one. The superhydrophilic surface can be an ideal heat transfer surface. Copyright © 2002 John Wiley & Sons, Ltd.     

On A Maximum Likelihood Method for Clustering

Behaviormetrika - In this paper, we propose a new clustering method based on the concept of maximum likelihood (ML) estimation. In general, the problem of local minima arises when we try to use the...     

Effect of surfactants on phenol removal by the method of polymerization and precipitation catalysed by Coprinus cinereus peroxidase

The removal of phenol by peroxidase‐catalysed polymerization was examined using Coprinus cinereus peroxidase in the presence of surfactants. The non‐ionic surfactants with poly(oxyethene) residues, Triton X‐100, Triton X‐405 and Tween 20, enhanced the phenol removal efficiency at a level similar to high relative molecular mass poly(ethylene glycol) (relative molecular mass 3000). Although the improvement in the removal efficiency was less than that of Triton X‐100, Span 20, sodium lauryl sulfate (SDS) and lauryl trimethylammonium bromide (DTAB) also enhanced the removal efficiency. The requirement of the enzyme for almost 100% removal of 100 mg dm^?3 phenol decreased to one‐fourth by the addition of 30 mg dm^?3 Triton X‐100. Triton X‐100, Triton X‐405, Tween 20 and DTAB could reactivate the enzyme precipitated with the phenol polymer, leading to the restarting of the phenol removal reaction. Copyright © 2003 Society of Chemical Industry     

Hierarchical Clustering Method Using Probabilistic Similarity Measure

In this paper, we propose a new hierarchical clustering method, which is useful to find appropriate clusters of attributes from given dichotomous or frequency data. Important features of our method are 1) the similarity between two attributes is defined as a probability of their pattern vectors being observed under the hypothesis of independence, 2) for each generated cluster, one pattern vector is defined in a natural manner, and 3) it can be used freely without distinguishing the frequency data from the dichotomous one.

A typical frequency data is analyzed to illustrate how our method works effectively. The discussion on similarities among objects is also included to propose a new similarity measure based on our clustering method.

     

Nosocomial diarrhoea in the elderly due to enterotoxigenic Clostridium perfringens

Zinc is an important trace element for immune function. Here, we show that zinc addition in a serum- and lipopolysaccharide-free cell culture system leads to significantly enhanced levels of interleukin 1 beta (IL-1 beta) and tumour necrosis factor alpha (TNF-alpha) and to expression of the corresponding mRNA in human peripheral blood mononuclear cells (PBMC). Structurally related divalent cations like cobalt, nickel, and mercury also partially increase monokine secretion but to a much lower and thus insignificant extent. They fail to induce mRNA of TNF-alpha after 3 h of culture. Therefore, monokine induction is a zinc-specific effect influenced by the physicochemical properties of the ion. Confirmation of the unique significance of zinc for immune function provides a better understanding of the mechanisms of specific zinc-mediated immune modulation.     

Nigrofrontal dopaminergic function as assessed by 18F-dopa PET

The existence of the nigrofrontal dopaminergic pathway has been demonstrated in neuroanatomical studies. We evaluated the presynaptic nigrofrontal dopaminergic function using 18F-dopa (FD) positron emission tomography (PET). The multiple time PET data in the frontal cortex from 20 to 70 min post-injection for FD were evaluated by Patlak analysis using the cerebellar time-activity curve as an input function. The frontal FD uptake rate constants could not be determined in 5 of 12 normal volunteers because of large deviations in the plots. There were no significant differences between the subjects among whom the frontal FD uptake rate constants could or could not be determined regarding the amount of FD injected, the frontal 18F counts, or whether or not they were pretreated with carbidopa. The uptake constants were determined in 9 or 12 patients with parkinsonian syndrome. While the mean (+/- S.D.) uptake constants in patients with Parkinson's disease (2.89 +/- 0.06 x 10(-3), n = 4) and in patients with progressive supranuclear palsy (2.81 +/- 0.10 x 10(-3), n = 3) were not significantly different from those in the normal volunteers (2.93 +/- 0.14 x 10(-3)), those in two patients with corticobasal degeneration (2.42 and 2.46, respectively) decreased in comparison to the control values. Differences in the nigrofrontal presynaptic dopaminergic function as assessed by FD-PET may explain the different pathogenesis and also help to differentiate between corticobasal degeneration and other parkinsonian syndromes, such as Parkinson's disease and progressive supranuclear palsy.