Relationships of tensile strength with crosslink density for the high-carbon black-filled EPDM compounds with various softeners

Equilibrium swelling and rheological tests were adopted to systematically investigate the effects of softener type and dosage on the crosslink densities. The results turned out that the chemical crosslink density could be distinguished from the physical crosslink density by comparing the results of equilibrium swelling and rheological tests. The liquid butadiene (LB) as a softener leads to the greatest reduction in crosslink density, followed by polyethylene wax (PW) and paraffinic oil (PO). The tensile strength decreases with increasing PO content while shows peak values with increase of LB and PW contents. The dependencies of chemical crosslink density on the aging time under 150°C are quite different for the three softeners, which can be expected from the double crosslinking networks consisting of small softener and large main crosslinking networks. Further investigation has been performed to correlate the tensile strength with chemical crosslink density of ethylene propylene diene monomer elastomer vulcanizates. Three different linear relationships can be obtained for the softeners independent of the aging time. It can now be expected from this study that the role of some new softeners in rubber compounds is not only confined to plasticization but also forms crosslinking networks in the peroxide-cured rubbers.     

Core–shell NTC materials with low thermal constant and high resistivity for wide-temperature thermistor ceramics

Core–shell structures have been proposed to improve the electrical properties of negative-temperature coefficient (NTC) thermistor ceramics. In this work, Al₂O₃-modified Co_1.5Mn_1.2Ni_0.3O₄ NTC thermistor ceramics with adjustable electrical properties were prepared through citrate-chelation followed by conventional sintering. Co_1.5Mn_1.2Ni_0.3O₄ powder was coated with a thin Al₂O₃ shell layer to form a core–shell structure. Resistivity (ρ) increased rapidly with increasing thickness of the Al₂O₃ layer, and the thermal constant (B) varied moderately between 3706 and 3846 K. In particular, Co_1.5Mn_1.2Ni_0.3O₄@Al₂O₃ ceramic with 0.08 wt% Al₂O₃ showed the increase of ρ double, and the change in its B was less than 140 K. The Co_1.5Mn_1.2Ni_0.3O₄@Al₂O₃ NTC ceramics showed high stability, and their grain size was relatively uniform due to the protection offered by the shell. The aging coefficient of the ceramic was less than 0.2% after aging for 500 hours at 125°C. Taken together, the results indicate that as-prepared Co_1.5Mn_1.2Ni_0.3O₄@Al₂O₃ NTC ceramics with a core–shell structure may be promising candidates for application as wide-temperature NTC thermistor ceramics.     

Se doped nickel-molybdenum bimetal sulfide with enhanced electrochemical activity for hydrogen evolution reaction

In this work, we synthesized Se doped MoS₂@Ni₃S₂ with nanosheets coated nanorods structure supported on Ni foam (MoNiSeS). Firstly, MoS₂@Ni₃S₂ (MoNiS) nanorods was synthesized by hydrothermal method. After selenization treatment, MoSe₂ successfully formed on the edge of MoS₂ nanosheets and particle Ni₃S₂ transformed into NiSe, in which MoSe₂ and NiSe acted as new phase in MoNiSeS. The obtained MoNiSeS only needs a low overpotential of 68 mV to reach the current density of 10 mA cm^?2, and has a low Tafel plots of 72.77 mV dec^?1 and good electrochemical durability, whose electrochemical activity is much better than that of MoNiS and NiSeS, implying the introduction of Mo and Se is beneficial to improve the electrocatalytic performance of NiS for HER. In addition, the proper amount of Mo source, which has an effect on the morphology of product, has also been investigated. For MoNiSeS, the typical nanosheets coated nanarods expose more active sites and the synergic effects is good to the improvement of the catalytic activity. Meanwhile, WNiSeS has also been prepared using the same method and the corresponding results show that the electrochemical activity of WNiSeS is much better than that of NiSeS, proving the universality of this strategy.     

某进口固体废物“铁精粉”的鉴别方法探析

为了确保不进口污染环境的固体废物，针对某冒充铁精粉的进口固体废物，通过外观、成分、物相分析进行了系统的鉴别。确定样品主要为经研磨加工的氧化铁皮，属于禁止进口的固体废物——轧钢产生的氧化皮。     

小像元红外探测器读出电路设计研究

介绍了基于SMIC 0.18 μm 3.3 V工艺设计研究的第一款小像元红外探测器读出电路,间距10 μm,规模1024×1024。文章详细介绍了像素输入级以及列级、输出级运放的设计,为提高线性摆伏,设计选用了低阈值NMOS管nmvt 33,仿真分析证明低阈值管nmvt 33的噪声性能优于普通管n 33；版图设计对关键信号线和敏感点采取隔离处理措施,对像元间串扰进行了仿真分析,有效控制了信号串扰。电路经测试使用各项功能正常,最大电荷处理能力达到4.3 Me-,动态范围≥65 dB,读出速率达到10 MHz,性能指标满足设计要求。     

黑匣子高温测试仪的开发

采用物质的相变吸热原理，可以将高温环境传人保温箱的热量重新排回至高温环境，有效地提高了保温箱的抗高温能力，并对保温箱的隔热性能做了简单的理论推算和测温反向试验。温度测试仪选用超低功耗CPU，具有体积小、耗电少的优点，使黑匣子高温测试仪在运行过程中具有很好的安全可靠性。     

有关工程建设管理现状的一些思考

为了促进我国工程建设管理由粗放式向科学化、规范化管理的转变,国家针对影响工程建设管理的几个关键环节,提出了“四制”:为了明确管理主体责任,实行了项目法人负责制;为了引进市场竞争机制,实行了招标投标制;为了实现工程质量全面专业化管理,实行了建设监理制;为了规范工程建     

NUMERICAL INVESTIGATION ON MUD BED-GENERATION AND IMPACTING A WALL ALONG A SLOPE

In this paper mud was treated as the Bingham fluid. In staggered grids, two-dimensional incompressible Navier-Stokes equations for non-Newtonian fluid was solved by the MAC method. Numerical simulations were conducted on mud bed-generating phenomenon and mud impacting a wall along a slope. The distributions of free surface, pressure and velocity of mud and water were obtained. The results indicate that the computed layer thickness of mud bed almost equals the theoretically predicted value. Because of the differences in constitutive relationship, the distributions of free surface are different for water and mud. The distortion of water free surface is much more complicated.     

风管摩擦阻力的直接计算方法

提出用高精度的反映密度、黏度和温度关系的经验公式和Colebrook公式计算风管摩擦阻力系数的方法。分析和算例表明，用该方法计算，计算结果比采用常用工程设计方法更为准确，为应用计算机进行风道设计提供了直接、简便的方法。