Fabrication of lotus-type porous carbon steel by the continuous zone melting method and its mechanical properties

A lotus-type porous carbon steel with cylindrical pores was fabricated by the continuous zone melting method in a pressurized mixture of hydrogen and helium gases. The porosity increases with increasing partial pressure of the hydrogen gas, while the pore diameter remains almost constant, independent of the pressure. The ultimate tensile strength of the specimen with cylindrical pores parallel to the tensile direction is lower than the estimated value, assuming that the strength is decreased in proportion to the decrease of the cross-sectional area of the specimen, while the yield strength is higher than the estimated value. The compressive yield strength is also higher than the estimated value. The increase in yield strength is considered to be due to precipitation strengthening. The tensile strength is increased by quenching and tempering, while the elongation decreases. Such mechanical properties are discussed in terms of the microstructural analysis.     

声波测井换能器激发响应实验研究

声波测井换能器的激发响应由换能器振动时所表现出来的动态阻抗和激发电路参数决定。而换能器的动态（阻抗）参数随压电晶体及其装配方式（力学边界条件）改变。为了测量换能器动态参数的影响，采用声波测井仪器常用的压电晶体和升压变压器，通过改变激发脉冲宽度和直流电压进行了实验，结果发现：在换能器两端的瞬态响应中，一共有三个二阶网络响应，分别对应于不同的频率。最低的一个影响声波测井波形的基线、与换能器主频接近的一个决定激发效率以及电路与压电晶体之间的匹配关系，是激发电路设计中比较关键的，其参数可以通过导纳圆测量仪器得到。     

新设备技术在催化裂化装置上的应用

文章介绍了近年来在催化裂化装置上应用的新设备、新技术,如BY型旋风分离器、BSX型旋分式三级旋风分离器、上下拱型三级旋风分离器、下拱型三级旋风分离器、SHS“自蔓延”技术、SWY外取热器、BWJ型喷嘴、自流浇注料、Actehem高耐磨衬里、弓形钢丝纤维、侧拉环锚固钉、分体可拆人孔等的结构特点及实际应用情况。     

A decision support system for interactive decision making - Part II: analysis and output interpretation

For pt.I see ibid., p.42-55 (2003). The development of a comprehensive decision support system, GMCR II, for the systematic study of real-world interactive decision problems is presented. The companion paper (Part I), discusses how GMCR II elicits, stores, and manages conflict models; here (Part II), the focus is on GMCR IIs analysis and output interpretation subsystems. Specifically, this paper describes the powerful and efficient analysis engine contained in GMCR II, its informative output presentation and interpretation facilities, and a number of follow-up analyses. Furthermore, an illustrative case study is used to demonstrate how GMCR II can be conveniently applied in practice.     

Field Static Load Test on Kao-Ping-Hsi Cable-Stayed Bridge

Field load testing is an effective method for understanding the behavior and fundamental characteristics of a cable-stayed bridge. This paper presents the results of field static load tests on the Kao-Ping-Hsi cable-stayed bridge, the longest cable-stayed bridge in Taiwan, before it was open to traffic. A total of 40 loading cases, including the unit and distributed bending and torsion loading effects, were conducted to investigate the bridge behavior. The atmospheric temperature effect on the variations of the main girder deflections was also monitored. The results of static load testing include the main girder deflections, the flexural strains of the prestressed concrete girder, and the variations of the cable forces. A three-dimensional finite-element model was developed. The results show that the bridge under the planned load test conditions has linear superposition characteristics and the analytical model shows a very good agreement with the bridge responses. Further discussion of deflection and cable forces of the design specifications for a cable-stayed bridge is also presented.     

Synthesis of ZSM‐5 Films and Monoliths with Bimodal Micro/Mesoscopic Structures

A route to synthesize ZSM‐5 crystals with a bimodal micro/mesoscopic pore system has been developed in this study; the successful incorporation of the mesopores within the ZSM‐5 structure was performed using tetrapropylammonium hydroxide (TPAOH)‐impregnated mesoporous materials containing carbon nanotubes in the pores, which were encapsulated in the ZSM‐5 crystals during a solid rearrangement process within the framework. Such mesoporous ZSM‐5 zeolites can be readily obtained as powders, thin films, or monoliths.     

Passive alignment method of polymer PLC devices by using a hot embossing technique

A novel fabrication process using a hot embossing technique has been developed for micromechanical passive alignment of polymer planar lightwave circuit (PLC) devices. With only one step of embossing, single-mode waveguide straight channels and micropedestals for passive aligning are simultaneously defined on a polymer thin film with an accuracy of /spl plusmn/0.5 /spl mu/m. This process reduces the steps for fabricating alignment structures. A fabricated polymer PLC chip and fibers are combined on a v-grooved silicon optical bench (SiOB) in a flip-chip manner. The process provides a coupling loss as low as 0.67 dB per coupling face and a cost-effective packaging solution for various polymer PLC devices.     

High-performance MIM capacitor using ALD high-k HfO/sub 2/-Al/sub 2/O/sub 3/ laminate dielectrics

For the first time, we successfully fabricated and demonstrated high performance metal-insulator-metal (MIM) capacitors with HfO/sub 2/-Al/sub 2/O/sub 3/ laminate dielectric using atomic layer deposition (ALD) technique. Our data indicates that the laminate MIM capacitor can provide high capacitance density of 12.8 fF//spl mu/m/sup 2/ from 10 kHz up to 20 GHz, very low leakage current of 3.2 /spl times/ 10/sup -8/ A/cm/sup 2/ at 3.3 V, small linear voltage coefficient of capacitance of 240 ppm/V together with quadratic one of 1830 ppm/V/sup 2/, temperature coefficient of capacitance of 182 ppm//spl deg/C, and high breakdown field of /spl sim/6 MV/cm as well as promising reliability. As a result, the HfO/sub 2/-Al/sub 2/O/sub 3/ laminate is a very promising candidate for next generation MIM capacitor for radio frequency and mixed signal integrated circuit applications.     

Hydrogen annealing effect on DC and low-frequency noise characteristics in CMOS FinFETs

The hydrogen annealing process has been used to improve surface roughness of the Si-fin in CMOS FinFETs for the first time. Hydrogen annealing was performed after Si-fin etch and before gate oxidation. As a result, increased saturation current with a lowered threshold voltage and a decreased low-frequency noise level over the entire range of drain current have been attained. The low-frequency noise characteristics indicate that the oxide trap density is reduced by a factor of 3 due to annealing. These results suggest that hydrogen annealing is very effective for improving device performance and for attaining a high-quality surface of the etched Si-fin.     

Inside Front Cover: The Elastic Properties and Plastic Behavior of Two‐Dimensional Polymer Structures Fabricated by Laser Interference Lithography (Adv. Funct. Mater. 10/2006)

The probing of the micromechanical properties within a two‐dimensional polymer structure with sixfold symmetry fabricated via interference lithography reveals a nonuniform spatial distribution in the elastic modulus “imprinted” with an interference pattern in work reported by Tsukruk, Thomas, and co‐workers on p. 1324. The image prepared by M. Lemieux and T. Gorishnyy shows how the interference pattern is formed by three laser beams and is transferred to the solid polymer structure. The elastic and plastic properties within a two‐dimensional polymer (SU8) structure with sixfold symmetry fabricated via interference lithography are presented. There is a nonuniform spatial distribution in the elastic modulus, with a higher elastic modulus obtained for nodes (brightest regions in the laser interference pattern) and a lower elastic modulus for beams (darkest regions in the laser interference pattern) of the photopatterned films. We suggest that such a nonuniformity and unusual plastic behavior are related to the variable material properties “imprinted” by the interference pattern.