Influence of the preparation conditions on the size and morphology of nanocrystalline lanthanum orthoferrite

Nanocrystalline LaFeO₃ is prepared by the dehydration of coprecipitated lanthanum and iron(III) hydroxides. It is shown that the behavior of the samples during heating and the size distribution of LaFeO₃ nanocrystals can be considerably different depending on the scheme used for coprecipitation of lanthanum and iron hydroxides; independently of the method employed for coprecipitation of the initial compounds, sintering of the samples at 950°C leads to the formation of lanthanum orthoferrite crystals up to 100 nm in size.     

Effect of vibration condition and inter-particle frictions on the packing of uniform spheres

We present a numerical study of the packing of uniform spheres under three-dimensional vibration using the discrete element method (DEM), focusing on the effects of vibration condition (amplitude and frequency) and inter-particle frictions (sliding and rolling frictions). The results are analysed in terms of packing density, coordination number (CN), radial distribution function (RDF) and pore structure. It is shown that increasing either the vibration amplitude or frequency causes packing density to increase initially to a maximum and then decrease. Both vibration frequency and amplitude should be considered to characterize the effect of vibration process on packing structure. The sliding and rolling frictions between particles can decrease packing density since they dissipate energy, although the effect of rolling friction is less significant. In line with the change of packing density, microstructural properties such as CN, RDF and pore distribution also change: a looser packing often corresponds to smaller CN, less peaked RDF and larger but more widely distributed pores.     

客户机／服务器计算环境

本文介绍了客户机／服务器计算环境的基本概念和产生背景，阐述了客户机／服务器计算中操作系统的选择原则及企业级客户机／服务器计算环境的特点。     

镀锌测厚仪

本文叙述了Ｘ射线荧光测厚仪的原理、特点及测量头的设计考虑原则。并以我们研制的两种镀锌测得仪为例作了详细说明。     

HYSIM软件模拟天然气加工工艺流程的研究(Ⅰ)——系统中无循环物流

本文结合大庆油田天然气矿场加工实际生产装置,讨论了应用HYSIM烃类工艺模拟软件对含有不确定组分的体系进行流程模拟计算的特点、塔设备严格模拟计算过程中输入规定的选择、以及多股流换热器和吸附脱水工艺的模拟计算方法。     

纸张用有机硅抗水剂的制备

采用氨基硅油、十二烷基三甲氧基硅烷、甲基三乙氧基硅烷配成11种抗水剂,用于纸张的抗水处理.通过渗透法和接触角法测试发现,有机硅抗水剂对实验选择的9种纸张均有明显的抗水效果;其中采用氨基硅油配制的抗水剂效果最好,经其处理的生宣纸与空白样相比,接触角由完全润湿提高到125°,渗透时间由0提高到18 s.最佳应用工艺为:将氨基硅油配制成质量分数为2.041%的甲苯溶液,按照10g/m2的涂布量喷涂于纸张表面,自然晾干3～5天至恒定质量.     

Comparative study of the elimination of toluene vapours in twin biotrickling filters using two microorganisms Bacillus cereus S1 and S2

BACKGROUND: To investigate the microbial degradation performance of organic pollutants in the atmosphere using a biotrickling filter, two microorganism strains, Bacillus cereus S1 and Bacillus cereus S2, were selected, identified and inoculated into a twin biotrickling filter for comparison. RESULTS: Both strains showed good performance towards the degradation of model organic pollutants when gas flow rates ranged from 100 to 600 L h⁻¹. For S1, the total maximum removal efficiency (RE) of toluene was maintained nearly 100% not only at gas flow rates of 100 L h⁻¹ corresponding to empty bed residence time (EBRT) 199.44 s, but also at gas flow rates of 200 L h⁻¹ (EBRT = 99.72 s) and 300 L h⁻¹ (EBRT = 66.48 s). However, S2 had a much lower degradation capability; near 100% removal efficiency was obtained only at the gas flow rate of 100 L h⁻¹ although both bacteria belong to the same Bacillus cereus. With further increase in gas flow rate, the total REs for both S1 and S2 decreased slightly at first and then dropped sharply to 46% and 35%, respectively, at an EBRT of 33.24 s, corresponding to a gas flow rate of 600 L h⁻¹. Starvation for between 2 and 10 days resulted in the re‐acclimation times of both strains ranging between 1.0 and 15.5 h. CONCLUSION: Strain S1 would be a better choice for inoculation into a biotrickling filter than strain S2, because of its much higher toluene removal capacity and rapid recovery to full performance. Copyright © 2008 Society of Chemical Industry     

关系数据库在专家系统中的应用

在传统的专家系统中，对推理机工作过程的控制是程序实现的。本文介绍了一个用数据库技术引导推理过程的专家系统－精神分裂症诊断专家系统（ＥＳＳＤ）的推理控制策略。在这个专家系统中，作者将有关推理过程的控制信息用关系数据库技术进行存储和管理，达到了将控制策略数据化的目的。将数据库技术引入到专家系统的推进控制机制中可以使控制策略比较容易调整，且而可以大大压缩程序篇幅，显著提高系统运行效率，为专家系统的结构设     

D301树脂分离衣康酸的工艺研究

采用弱碱性阴离子交换树脂Ｄ３０１对发酵法生产的衣康酸进行了分离研究。通过静态交换实验，研究了Ｄ３０１树脂对衣康酸的静态交换动力学，确定了传质机制和影响因素；通过动态交换实验，研究了以硫酸为洗脱剂，以氨水为再生剂的工艺过程，确定了主要工艺参数。     

AGING BEHAVIOUR OF PARTICULATE REINFORCED ALUMINUM ALLOY MATRIX COMPOSITES

The process of aging precipitation in SiC_p/6061 and Al_2O_3/6061 composites were investigated. Hardness testing, differential scanning calorimetry(DSC) and transmission electron microscopy were employed. Results showed that the precipitation phase form directly along dislocation lines in the composites because the particles produce high densities of dislocations which makes vacancy densities in the composites decrease, and the main precipitation phase at peak hardness was β′ phase.