The MiniWiD-Coater. III. Effect of Application Temperature on the Dissolution Profile of Sustained-Release Theophylline Pellets Coated with Eudragit Rs 30 D

Theophylline pellets were coated with Eudragit RS 30 D in a miniature fluid-bed pan coater called MiniWiD developed recently. The dispersions were plasticized with varying amounts of triethyl citrate (TEC), dibutyl phthalate (DBP), and polyethylene glycol 6000 (PEG) and applied at different temperatures ranging from 25 to 45 °C. Theophylline release was tested by dissolution using the USP Apparatus 2 (paddle) in 0.1 N hydrochloric acid under sink conditions over 6 hours.

At a coating level of 4 % (0.7 mg/cm²) sustained-release profiles were obtained from dispersions plasticized with TEC or DBP. By reducing the amount of plasticizer from 20 to 10%, films with higher permeabilities were obtained. This effect was compensated by tempering the pellets at 50 deg;C for 24 hours. The coating temperature had little effect on the dissolution profiles of TEC-plasticized films and no effect on films with DBP.

Coatings plasticized with 20% PEG were applied at temperatures ranging from 25 to 45 °C. These films required a coating level of about 18 % (3.3 mg/cm²) to provide comparable sustained-release properties. In contrast to DBP and TEC, a strong influence of the coating temperature on the release rates was observed in which higher temperatures led to slower release rates. This behavior can be explained by the minimum film-forming temperature (MFT). Since PEG does not lower the MFT of Eudragit RS 30 D, the application of these films below the MFT of 45 °C is associated with a lower degree of film formation.     

Diarrhea in young children associated with Escherichia coli non-O157 organisms that produce Shiga-like toxin

The aim of this study was to evaluate the way in which short-term protection declines and is eventually lost in preconditioning and to determine the efficacy of a second preconditioning at various reperfusion intervals. Male rabbits were divided into six groups. Forty-five minutes (sustained) ischemia followed by 120 minutes reperfusion was applied 60, 65, 70, 75, and 80 minutes after a 5 minute preconditioning (groups A, B, C, D, and E) and in a control group (F) after no preconditioning. The infarct to risk ratio (I/R) was 38.3 +/- 3.5% in group A, 46.0 +/- 7.8% in B, 61.6 +/- 9.7% in C, 68.1 +/- 4.2% in D, 64.5 +/- 7.8% in E, and 61.0 +/- 7.7% in F. Group A had a smaller I/R compared with groups C, D, E, and F (p < 0.05). In another series, groups G, H, and I were exposed to two 5-minute preconditioning stimuli, separated, respectively, by 45, 60, and 75 minutes of reperfusion; 10 minutes after the last preconditioning, the animals were exposed to 45-minutes ischemia and 120 minutes reperfusion. Groups A and D (with the smaller and higher I/R ratio) were also incorporated into this protocol in order to compare the effect of the additional preconditioning with the single one. The I/R ratio was 25.4 +/- 8.5% in group G, 22.8 +/- 7.0% in group H, and 14.7 +/- 4.0% in group I (p = NS). Group D showed a higher I/R compared with groups G, A, and H (p < 0.01), and group I had a smaller I/R compared with groups A (p < 0.01) and D (p < 0.001). Cardioprotection after a first preconditioning declines gradually and is eventually lost. An additional preconditioning is always effective, and the longer the interval from the first preconditioning, the more potent is the effect.     

Psychoanalytic considerations of right extremist orientation of male adolescents

Giving a case example of an male adolescent with radical right-wing attitudes, the lack of male identification as well as in unresolved dyadic fixation to the mother will be shown. Though the radical right-wing orientation the adolescent tries on the basis of a phallic narcissistic conflict to establish bordes against an unresolved dyadic fixation to his mother.     

Überlegungen zur Erweiterung des Klebstoffangebots im Holzleimbau

The procedure of testing adhesives for glulam production depends in Europe on the kind of resin. For example the testing of phenol-formaldehyde resins (PF-resins) includes the boiling test method, because the curing rate of these resins show a significant correlation between the strength after boiling and the resistance to moisture influence. On the other hand this test method is commonly insufficient for testing other resins. The results of investigations of glulam based on different kinds of resins show that there is a possibility to substitute the boiling test by a short-time accelerated aging method (KZB-Test) which will offer the same differentiation.     

Homogenization of hardness distribution and distortion in high pressure gas quenching

Quenching with gases rather than oil or other liquid media has the advantages of reducing the risks concerning health and environment, while simultaneously homogenizing the quenching results and minimizing distortion due to a wide range of possible process parameter variations and the pure convective heat transfer. In this contribution, a coupled solution for increasing homogenization of quenching results within high pressure gas quenching will be presented. In the first stage, an experimental test facility was set up for flow investigations and in the second stage a numerical simulation model was generated. The numerical and experimental results of the flow through the chamber were compared for several boundary conditions. Finally, after complete verification of the simulation, the model may be used to assist in parameter variation for optimization of homogeneous high pressure gas quenching.     

Simulation based on learning methods

The use of simulation technology as a tool for planning and control is of increasing significance in most fields of production. The main part of the expenditure concerning simulation analyses is the modelling of the considered production. Despite the use of modern building-block-oriented modelling technology, this modelling can often not be done by the user, but only by external experts. Against this backdrop, an adaptive simulation system is being developed by the Institute for Industrial Manufacturing and Management (IFF) at the University of Stuttgart. It independently adapts to real production processes, i.e. it learns about the interdependencies of production processes, and, in this way, supports the user in constructing and maintaining the model. In terms of information technology, the research in the field of artificial intelligence, especially in the subdomain of machine learning, is the basis for the realization of such adaptive systems.     

Schrifttumsberichte

Ohne Zusammenfassung