Performance failure analysis of EDFA cascades in optical DWDM packet-switched networks

A simple and comprehensive technique to determine the probability that a cascade of erbium-doped fiber amplifiers (EDFAs) may be driven into unacceptable regimes of bit error rate (BER) and/or gain levels is presented. This technique allows network designers to determine the tolerances by which the signal power levels may deviate from their predesigned average values and still give acceptable gain variances and BERs at the receiver. We show that even in the signal power range well above the receiver sensitivities (-38 dBm/ch) where the gain spread is not significant, the corresponding spread in BER due to random arrival of packets might result in unacceptable performance. We show for typical levels of operation, the BER temporarily (for about 3 /spl mu/s) deviates to below 10/sup -9/ (10/sup -15/) with a probability of 10/sup -3/ (10/sup -2/), for 100 (64) channels. We show that the gain spread for a single EDFA can be negligible for a range of signal and pump powers at a given average gain.     

Photocrosslinked biobased phase change material for thermal energy storage

A series of novel photocrosslinked biobased shape‐stabilized phase change materials (PCMs) based on octadecanol, eicosanol and docosanol have been prepared by UV technique for the purpose of thermal energy storage applications. Epoxidized soybean oil was reacted with acrylic acid to form acrylated soybean oil (ASO). The structure and composition, cross‐section morphology, thermal stability performances and phase change behaviors of ASO and UV‐cured PCMs were examined by using Attenuated total reflection fourier transform infrared spectroscopy, thermogravimetric analysis system (TGA), scanning electron microscopy, and differential scanning calorimetry. The results indicate that the UV‐cured biobased PCMs possess perfect phase change properties and a suitable working temperature range. The heating process phase change enthalpy is measured between 30 and 68 J/g, and the freezing process phase change enthalpy is found between 18 and 70 J/g. The decomposition of UV‐cured PCMs started at 260 °C and reached a maximum of 430 °C. All the biobased UV‐cured PCMs improved latent heat storage capacity in comparison with the pristine ASO sample. With the obtained results we conclude that, these materials promise a great potential in thermal energy storage applications. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43757.     

Preparation and thermal properties of polyethylene terephthalate/huntite–hydromagnesite composites

In this report, it was aimed to the improve thermal stability of polyethylene terephthalate (PET) by adding huntite/hydromagnesite minerale. PET/huntite/hydromagnesite composites were prepared by adding various proportions of huntite/hydromagnesite to PET. The chemical structures of the composites were characterized by Fourier transform infrared spectroscopy (FTIR) and X‐ray diffraction (XRD) analysis. Thermal properties of the composites were determined by thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). Glass‐transition temperatures and char yields increased with the increase of the huntite/hydromagnesite content in the composites. The surface morphologies of the composites were investigated by a scanning electron microscopy. The obtained results proved that the composite system is more thermally stable than the pure PET itself. POLYM. COMPOS., 37:3275–3279, 2016. © 2015 Society of Plastics Engineers     

Synthesis and characterization of polyimide/hexagonal boron nitride composite

Polyimide (PI)/hexagonal boron nitride (h‐BN) composites were produced via the thermal imidization procedure from solution mixtures of a polyamicacid, which is prepared from 3,3′,4,4′‐benzophenonetetracarboxylic dianhydride and 3,3′‐diaminodiphenyl sulfone (DADPS) in N‐methyl‐2‐pyrrolidone (NMP), and alkoxysilane functionalized h‐BN. The structure, thermostability, thermal behavior, and surface properties of the resulting materials were characterized by means of Fourier transform infrared spectroscopy (FTIR), differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), scanning electron microscopy (SEM). The thermal characteristics of PI/h‐BN films were better than the pure PIs. The physical and mechanical properties of the films were evaluated by various techniques such as contact angle, chemical resistance, and tensile tests. The flame retardancy of the composite materials was also examined by the limiting oxygen index (LOI). The experiments showed that the LOI values of PIs increased from 32 to 43 for the materials containing hexagonal boron nitride. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

A novel UV‐cured interpenetrating organic–inorganic hybrid polymer network based phase change materials (IPN‐PCM)

The purpose of this paper is to introduce a novel UV‐cured interpenetrating polymer networked phase change materials (IPN‐PCMs), on which no article has been found in the so far published research. Maleated castor oil (MCO) was synthesized via maleinization reaction of castor oil with maleic anhydride. Organic–inorganic hybrid interpenetrating polymer networked (IPN) materials containing both cationic and radical sections and IPN‐PCMs containing tetradecanol, hexadecanol, and octadecanol were prepared. The chemical structure of MCO and organic–inorganic hybrid IPN‐PCMs were determined by using Fourier Transform Infrared Spectroscopy (FT‐IR). Differential scanning calorimetry (DSC) was used for examining the phase‐change behaviors of the materials. Thermal stability was investigated by thermogravimetric analysis (TGA). Moreover, the surface formation of the specimen was investigated by scanning electron microscopy (SEM). In conclusion, our study proved that because of their high latent heat storage scope and high thermal stability, the obtained organic–inorganic hybrid IPN‐PCMs could be used as thermal energy storage materials. POLYM. ENG. SCI., 58:870–875, 2018. © 2017 Society of Plastics Engineers     

Synthesis of fluorinated/methacrylated epoxy based oligomers and investigation of its performance in the UV curable hybrid coatings

Organic–inorganic hybrid coatings based on fluorinated/methacrylated soybean oil and bisphenol A/F epoxy methacrylate were obtained by combining photopolymerization and sol–gel process. Hard and transparent hybrid coatings were prepared on polycarbonate panels and their physical and mechanical properties such as gel content, hardness, adhesion, gloss, contact angle as well as tensile strength were measured. Results from the mechanical measurements showed that the properties of hybrid coatings improved with the increase in fluorine and sol–gel precursor contents. Thermo gravimetric analysis results demonstrated that fluorine and silica incorporations significantly enhanced the thermal oxidative stability of the hybrid coating materials. The surface morphology was also characterized by scanning electron microscopy (SEM). SEM studies indicated that inorganic particles were dispersed homogenously throughout the organic matrix.     

Inhibition of atmospheric corrosion of mild steel by sodium benzoate treatment

The objective of this study was to evaluate the effectiveness of sodium benzoate as an inhibitor to slow down or prevent atmospheric corrosion/discoloration of the local mild steel during storage in the Arabian Gulf region. Test specimens were prepared from locally produced reinforcing steel products. The inhibitor solution was applied on steel specimens at a concentration of 100 mM for 1 day at room temperature. Wooden exposure racks were used to hold as-received and inhibitor-treated specimens during atmospheric exposure for different periods. Corrosion was evaluated through weight loss determination and electrochemical technique. As expected, the Arabian Gulf atmosphere was corrosive on the as-received local mild steel. On the other hand, treatment of steel with sodium benzoate lowered its corrosion rate during initial days of its exposure to atmosphere. However, atmospheric corrosion inhibition performance of sodium benzoate deteriorated with exposure time after 30 or more days of atmospheric exposure, and the corrosion rates of sodium benzoate-treated specimens reached that of the unprotected specimens at the end of 90 days of atmospheric exposure.     

Hexavalent chromium removal by Osage Orange

This study explores the sorption potential of Osage Orange (Maclura Pomifera) for the removal of Cr(VI) ion. The influence of contact time, solution pH, initial metal concentration, amount of biosorbent and ionic strength on the removal of Cr(VI) ion was studied. The biosorption of Cr(VI) with pulp and peel was investigated in a batch arrangement. The initial and equilibrium concentrations of Cr(VI) ions in aqueous phase were determined by spectrophotometry. The sorption process was pH and concentration dependent. The sorption of Cr(VI) ions increased with a decreasing pH until pH 2. The increase in initial Cr(VI) ions concentration in aqueous phase increased the sorption. The sorption data fitted well with the Langmuir sorption model within the concentration range studied. The observed maximum biosorption capacity by Langmuir sorption model at pH of 2 for M. Pomifera pulp was 0.92 mmol of Cr(VI)/g and for M. Pomifera peel was 0.55 mmol of Cr(VI)/g.     

Investigation of the Microstructural,Mechanical and Corrosion Properties of Grade A Ship Steel-Duplex Stainless Steel Composites Produced <Emphasis Type="Italic">via</Emphasis> Explosive Welding

Grade A ship-building steel-AISI 2304 duplex stainless steel composite plates were manufactured via explosive welding. The AISI 2304 plates were used to clad the Grade A plates. Optical microscopy studies were conducted on the joining interface for characterization of the manufactured composite plates. Notch impact, tensile-shear, microhardness, bending and twisting tests were carried out to determine the mechanical properties of the composites. In addition, the surfaces of fractured samples were examined by scanning electron microscopy (SEM), and neutral salt spray (NSS) and potentiodynamic polarization tests were performed to examine corrosion behavior. Near the explosion zone, the interface was completely flat, but became wavy as the distance from the explosion zone increased. The notch impact tests indicated that the impact strength of the composites decreased with increasing distance from the explosion zone. The SEM studies detected brittle behavior below the impact transition temperature and ductile behavior above this temperature. Microhardness tests revealed that the hardness values increased with increasing distance from the explosion zone and mechanical tests showed that no visible cracking or separation had occurred on the joining interface. The NSS and potentiodynamic polarization tests determined that the AISI 2304 exhibited higher corrosion resistance than the Grade A steel.     

Preparation and thermal properties of Alkoxy Silane functionalized polyether sulfone/well‐defined poly(trimethoxysilyl) propyl methacrylate‐based hybrid materials

In this study, novel polyethersulfone (PES) and poly(trimethoxysilyl) propyl methacrylate (PMPS) containing hybrid materials were prepared. PES was functionalized with trimethoxysilane groups by UV‐induced grafting reaction. PMPS was synthesized by atom transfer radical polymerization. In the followed process, the functionalized PES mixed with different amount of PMPS, thermally treated to promote sol–gel crosslinking process to prepare the PES‐based hybrid materials. The trimethoxysilane grafted PES chains are covalently bonded with the well‐defined trimethoxysilane groups of PMPS. The chemical structure of the prepared PES and PMPS is confirmed by Fourier transform infrared analysis. The morphology of the hybrids was investigated by scanning electron microscopy. The results of thermogravimetric analysis show that the thermal stability of the hybrid materials was significantly affected with the addition of PMPS. POLYM. ENG. SCI., 58:1346–1352, 2018. © 2017 Society of Plastics Engineers