Formation of Zinc–Antimony-Based Spinel Phases

Formation of spinel phases in ZnO–Sb₂O₃and ZnO–Sb₂O₃–Bi₂O₃systems is studied by the use of X-ray diffraction. The formation of nonstoichiometric Zn_2.33Sb_0.67O₄phase is observed in both the systems at ∼900°C. However, in these systems, at higher temperatures ( T ≥ 1100°C), formation of the inverse spinel phase Zn₇Sb₂O₁₂is observed. The study has been extended to understand the effect of CrO₃doping on the stability of the different spinel phases in the previously mentioned systems. Interestingly, in both the systems, samples doped with CrO₃, displayed the presence of Zn_2.33Sb_0.67O₄phase <1200°C, indicating the stabilization of the spinel phase by CrO₃.     

Hydrogen storage in TiO2 functionalized (10, 10) single walled carbon nanotube (SWCNT) – First principles study

Hydrogen storage in titanium dioxide (TiO₂) functionalized (10, 10) armchair single walled carbon nanotube (SWCNT) is investigated through first principle calculations using density functional theory (DFT). This first principles study uses Vienna Ab-initio Simulation Package (VASP) with ultrasoft pseudopotentials and local density approximation (LDA). The necessary benchmark and other systematic calculations were carried out to project the hydrogen storage capability of the designed system. Interestingly, the TiO₂ molecules functionalized on the outer surface of SWCNT do not undergo any dimerization/clustering thus giving excellent stability and usable gravimetric hydrogen storage capacity of 5.7 wt.% and the value nearly fulfills the US DOE target (i.e. 6 wt.%). The band structure and density of states (DOS) plots suggest that the functionalization can lead a way to transform the nature (metallic → semiconducting) of the pristine SWCNT. The nominal values of H₂ storage capacity and binding energies give much hope for using CNT functionalized with TiO₂ as a practical and reversible hydrogen storage medium (HSM).     

Estimating ground-level PM2.5 in the eastern United States using satellite remote sensing

An empirical model based on the regression between daily PM2.5 (particles with aerodynamic diameters of less than 2.5 microm) concentrations and aerosol optical thickness (AOT) measurements from the multiangle imaging spectroradiometer (MISR) was developed and tested using data from the eastern United States during the period of 2001. Overall, the empirical model explained 48% of the variability in PM2.5 concentrations. The root-mean-square error of the model was 6.2 microg/m3 with a corresponding average PM2.5 concentration of 13.8 microg/m3. When PM2.5 concentrations greater than 40 microg/m3 were removed, model results were shown to be unbiased estimators of observations. Several factors, such as planetary boundary layer height, relative humidity, season, and other geographical attributes of monitoring sites, were found to influence the association between PM2.5 and AOT. The findings of this study illustrate the strong potential of satellite remote sensing in regional ambient air quality monitoring as an extension to ground networks. With the continual advancement of remote sensing technology and global data assimilation systems, AOT measurements derived from satellite remote sensors may provide a cost-effective approach as a supplemental source of information for determining ground-level particle concentrations.     

Low-temperature deformation behaviour of polycrystalline copper

Low-temperature plastic flow in copper was investigated by studying its tensile and creep deformation characteristics. The dependence of the flow stress on temperature and strain rate was used to evaluate the thermal activation energy while the activation area was derived from the change-in-stress creep experiments. A value of 0.6 eV was obtained for the total obstacle energy both in electrolytic and commerical copper. The activation areas in copper of three selected purities fell in the range 1200 to 100 b². A forest intersection mechanism seems to control the temperature dependent part of the flow stress. The increase in the athermal component of the flow stress with impurity content in copper is attributed to a change in the dislocation density. The investigation also revealed that thermal activation of some attractive junctions also takes place during low-temperature creep. The model of attractive junction formation on a stress decrement during creep, yields a value of 45±10 ergs cm⁻² for the stacking fault energy in copper.     

Response of materials as a function of grinding angle on friction and transfer layer formation

Surface texture influences friction and transfer layer formation during sliding contact. In the present investigation, basic studies were conducted using an inclined pin-on-plate sliding apparatus to understand the effect of grinding mark directionality on the coefficient of friction and transfer layer formation. In the experiments, 080 M40 steel plates were ground to attain different surface roughness with unidirectional grinding marks. Pins consisting of soft materials (pure Al, pure Mg, and Al–4Mg alloy) were then slid against the prepared steel plates. The grinding angle (angle between direction of sliding and grinding marks) was varied between 0° and 90° in the tests. The experiments were conducted under both dry and lubricated conditions in an ambient environment. It was observed that the transfer layer formation and the coefficient of friction depend primarily on the directionality of the plate grinding marks. For the case of pure Mg pins, a stick-slip friction phenomenon was observed for all grinding angles under dry conditions and for grinding angles over 25° under lubricated conditions. In the case of Al pins, the stick-slip phenomenon was observed only under lubricated conditions for angles exceeding 25°. The stick-slip phenomena did not occur in any of the conditions studied with Al–4Mg alloy pins. Based on the results, it was concluded that the magnitudes of the friction and the stick-slip motion amplitude (for Al and Mg pins) were primarily controlled by changes in the level of plowing friction.     

Fabrication and Tunable Dielectric Properties of (Ba0.7Sr0.3)TiO3-Glass-Based Thick-Film Capacitors

Ferroelectric glass–ceramics of composition 0.90 (Ba_0.7Sr_0.3) TiO₃–0.10(B₂O₃:SiO₂) (0.90 BST:0.10 BS) synthesized by sol–gel method have been used for the preparation of dielectric thick-film inks. The particle dispersion of the glass–ceramic powders in the thick-film ink formulations have been studied through rheological measurements for fabricating thick-film capacitors by screen printing technique. The thick films derived from such glass–ceramics are found to sinter at considerably lower temperatures than the pure ceramic, and exhibit good dielectric characteristics with a tunability of 32% at 1 MHz under a dc bias field of 35 kV/cm.     

Improving tribocorrosion performance of chemically bonded ceramic phosphate coating reinforced by GO-ZnO

To enhance the tribocorrosion properties of chemically bonded phosphate ceramic coating (CBPCC), GO-ZnO was prepared and added into CBPCC. And the tribocorrosion behaviour of CBPCC was investigated. Results show that, with the introduction of GO-ZnO, the open circuit potential of CBPCC shifts in a positive direction and corrosion current density decreases. In addition, the total material loss, the total mechanical wear loss and the total electrochemical corrosion loss of CBPCC all decrease with the increase of GO-ZnO. The wear track of CBPCC after tribocorrosion without GO-ZnO is rough and porous, while the wear track becomes smooth and dense with the incorporation of GO-ZnO. The material in wear track is anchored by GO-ZnO due to the strong bond between GO-ZnO and CBPCC, which decreases the wear loss. Because of the extra force from the tribocorrosion experiment, the material anchored by GO-ZnO forms to a dense structure which prevents electrolyte diffusion into CBPCC. Moreover, GO-ZnO can block the electrolyte diffusion pathway and make it more tortuous. The resistance to the electrolyte diffusion decreases the corrosion current density and the increased wear loss due to electrochemical corrosion.     

Direct reconstruction of complex refractive index distribution from boundary measurement of intensity and normal derivative of intensity

We present an optical tomographic reconstruction method to recover the complex refractive index distribution from boundary measurements based on intensity, which are the logarithm of intensity and normal derivative of intensity. The method, which is iterative, repeatedly implements the forward propagation equation for light amplitude, the Helmholtz equation, and computes appropriate sensitivity matrices for these measurements. The sensitivity matrices are computed by solving the forward propagation equation for light and its adjoint. The results of numerical experiments show that the data types ln(I) and partial differential I/ partial differential n reconstructed, respectively, the imaginary and the real part of the object refractive index distribution. Moreover, the imaginary part of the refractive index reconstructed from partial differential I/ partial differential n and the real part from ln(I) failed to show the object's inhomogeneity. The value of the propagation constant, k, used in our simulations was 50, and this value resulted in smoothing of the reconstructed inhomogeneities. Thus we have shown that it is possible to reconstruct the complex refractive index distribution directly from the measured intensity without having to first find the light amplitude, as is done in most of the currently available reconstruction algorithms of diffraction tomography.     

Mechanical Properties and Dry Sliding Wear Behaviour of Molybdenum Disulphide Reinforced Zinc–Aluminium Alloy Composites

ZA-27 alloy is a lightest alloy which offers excellent bearing and mechanical properties in automobile and industrial applications. In this study, the MoS₂ particles with 0.5, 1 and 1.5 (wt%) weight percentages were reinforced in ZA-27 alloy to form composites, which were fabricated by using ultrasonic assisted stir casting method. The ZA-27/MoS₂ composite specimens were examined for chemical composition with the aid of XRD technique and EDS. Microstructure analysis of the ZA-27/MoS₂ composites was studied using SEM. Tests were conducted for mechanical properties such as tensile strength and hardness on ZA-27/MoS₂ composites samples as per ASTM standards. Dry sliding wear behavior of the composites was tested at various operating conditions by using pin-on-disc apparatus. Microstructural images of the ZA-27 composites reveal that there is a uniform dispersion of the MoS₂ particles in the base material. From the results it is observed that the mechanical properties increases with ZA-27 reinforced with 0.5 wt% MoS₂ composite and further decreases with increase in the filler content. The enhanced wear resistance is observed in ZA-27 reinforced MoS₂ composites as compared to the unreinforced alloy. The wear rate of the ZA-27 composites decreases with the increase in filler content, further the worn surfaces as examined using SEM reveals the wear mechanism explaining the improved wear resistance of the particulate composites.     

Analysis of Nanofluids as Cutting Fluid in Grinding EN-31 Steel

Nano-Micro Letters - Grinding requires high specific energy which develops high temperatures at wheel work piece interface. High temperatures impair work piece quality by inducing tensile residual...