A 10-s doping technology for the application of low-temperaturepolysilicon TFTs to giant microelectronics

A bucket-type high-density (0.25-1.2-mA/cm²) low-energy (500-2000 V) ion source was utilized for high-speed phosphorus doping directly into a thin polysilicon layer without cap SiO₂. Doping gas with He dilution was selected to reduce etching of polysilicon film. Excimer laser (XeCl, 8 mm×8 mm) pulse annealing was introduced to activate effectively the doped impurity. The combination of these techniques provided a practically low sheet resistance for the TFT source, drain, and gate with a short time doping. The low-temperature polysilicon TFT fabricated with a doping time of 10 s had characteristics comparable to those of that fabricated by a longer time doping or conventional ion implantation, showing the practicality of this technology and its promise for giant microelectronics     

Changes in Aging Behavior and Defect Structure of Yttria-Fully-Stabilized ZrO2 with Sc2O3 Doping

Methods of suppressing decreased conductivity in 8 mol% Y₂O₃-stabilized–92 mol% ZrO₂ (8YSZ) with aging were investigated. Different amounts of Sc₂O₃ were doped into 8YSZ. The electrochemical properties of Sc₂O₃-doped 8YSZ were measured, and the microstructural and local structural changes were characterized. The present results indicate that an appropriate amount of Sc₂O₃ doping, 3 or 4 mol%, effectively suppresses decreased conductivity with aging in 8YSZ.     

Interface potential of calcium phosphate in simulated body fluid

Calcium phosphate ceramics are used in the substitution of injured or damaged bones. Nevertheless, the behaviour of these materials, and in particular, the mechanisms guiding their interface response in physiological environment is still unknown. This work describes the construction of hydroxyapatite and tricalcium phosphate electrodes used to determine the interface potential behaviour of these materials in a simulated body fluid, in a pH range corresponding to the variation observed in human body injuries, at ambient and physiological temperatures. These measurements are associated with the adsorption/desorption of ions from the materials. The results show that hydroxyapatite and tricalcium phosphate have similar behaviour in that they reach an interface potential equilibrium state faster when the solution pH is decreased and the temperature increased. This behaviour may be attributed to their ability to form a calcium-rich layer and is relevant to their quality as implantable materials.     

Hydrothermal preparation of tailored hydroxyapatite

Hydrothermal vapor treatment method was applied for preparation of ceramic biomaterials. Hydroxyapatite (Ca₁₀(PO₄)₆(OH)₂; HA) ceramics prepared by sintering with random crystal surface have already been used as bone-repairing materials which can directly bond to natural bones. If materials of HA could have the tailored specific crystal surface, they should have the advantage of adsorptive activity and osteoconductivity in comparison with the sintered HA. In the present study, porous HA sheets of about 50 μm to 1 mm in thickness and porous HA granules of about 50 μm to 1 mm in size with tailored crystal surface were prepared by the hydrothermal vapor exposure method at temperatures below 200°C. Porous sheets and porous granules of HA with controlled crystal surface should be suitable for scaffold of cultured bone, for bone graft material and for drug delivery system (DDS).     

Demonstration of a fully spatial coherent X-ray laser at 13.9 nm

We have recently reported the successful development of a fully coherent X-ray laser (XRL) at 13.9 nm by an oscillator-amplifier configuration with two targets. In the experiment, a seed XRL beam from the first target is injected into a plasma amplifier at the second target. The observed XRL beam has full spatial coherence and 0.2 mrad of nearly diffraction-limited divergence. In order to improve the output fluence, the amplification properties of the XRL beam have been investigated using various plasma lengths of the second amplifier target. The output energy has been improved by a factor of ten, increasing the length of the gain region to 10 mm, resulting in about 0.2 /spl mu/J of output energy.     

Enantioselective addition Of diketene to aldehydes promoted by chiral schiff base—titanium alkoxide complex. Application to asymmetric synthesis of potential inhibitors of HMG coenzyme reductase

Highly enantioselective addition of diketene to aldehydes was achieved by using novel Schiff base—titanium alkoxide complexes. Up to 92% ee of 5-hydroxy-3-oxoesters was obtained. This procedure provides an efficient method for the asymmetric synthesis of potential inhibitors of HMG coenzyme reductase.     

Questionnaire of cryopreserved allograft valves in Kyushu and Yamaguchi area

Japanese Society of Cryopreserved Thoracic Tissue Implantation was recently set up. Cryopreserved allograft valves are about to pervade in Japan. To clarify the interest, demands and supply of cryopreserved allograft valve in the area of Kyushu and Yamaguchi, we performed questionnaire investigation regarding this issue. Collection rate of this questionnaire was 87.5% (35/40 hospitals). Ninety-seven percent of the hospitals answered that they were interested in cryopreserved allograft. Ninety-four percent of the hospitals answered that they did not ethically hesitate to use cryopreserved allograft. Ninety-one percent of the hospitals hoped to perform cardiac surgery using allograft aortic valve if allograft is available. With respect to securing donors of allograft, two-third of the hospitals did not decide whether they could be involved in obtaining donors of allograft. As the number of the cadaver kidney donors is about 20 per year in the area of Kyushu and Yamaguchi, shortage of donors of allograft valve is anticipated.     

Wholly synthesised VAD single-mode fibre

The first trial on the fabrication of completely synthesised VAD single-mode fibre is reported. Successful formation of a large deposited cladding-to-core diameter ratio of 10 leads to redundancy of silica jacketing tubes.     

Fabrication of low-loss single-mode fibres

Low-loss single-mode fibres with GeO2-doped SiO2 cores have been made by the c.v.d. method and the loss spectrum from 0.6 to 1.8 ?m measured. The minimum loss of the fibre with suitably designed parameters, characterised by the refractive-index difference and the core diameter, was 0.75 dB/km at 1.05 ?m.