Structural changes of glass-ceramics of the Cu2O-Al2O3-SiO2 system on heating in air

The behaviour of copper ions in low thermal expansion glass-ceramics prepared from Cu₂O · Al₂O₃ ·_nSiO₂ glasses, or in-spodumene type Cu₂O · Ae₂O₃ ·nSiO₂ crystals included in the glass-ceramics on heating in air was investigated. On hewing at 300 to 500° C, the copper ions behaved as in the corresponding glasses. Cuprous ions in the glass-ceramics or-spondumene type crystals were oxidized into the cupric state, and at the same time an equal amount of cuprous ions to those oxidized were expelled out of the specimen for the requirement of electrical charge neutrality and then reacted with oxygen to form CuO on the surface. The oxidation of cuprous ions and the decrease of the copper content of the-spondumene type crystals brought about a considerable decrease in the lattice spooings.     

Reduction of higher harmonic sequences in terminal voltage of an AC exciting synchronous generator using magnetically anisotropic slot wedges

This paper describes relationships between characteristics of a magnetically anisotropic slot wedge and voltage higher harmonics in an ac exciting synchronous generator terminal due to permeance ripple caused by an open-slot-type rotor. From the relationships obtained, practical guidelines were formulated for machine designs applying the magnetically anisotropic slot wedge. The results are as follows.

• 1 (1) Equivalent permeability of the magnetically anisotropic slot wedge became isotropic wedge permeability for air-gap flux ripple.
• 2 (2) Two ways were identified to reduce voltage-higher harmonics by using the slot wedges.
• 3 (3) The level of leakage flux passing through the anisotropic slot wedge was determined only by its permeability in the width direction.
• 4 (4) Effectiveness of the magnetic anisotropic slot wedges inserted into the stator slots was verified from experimental results using a model machine of the open- slot-type rotor.

     

Optical computing: introduction by the feature editors

This feature issue of Applied Optics: Information Processing contains 19 papers on Optical Computing. Many of these papers are expanded versions of presentations given at the Optical Society of America's Sixth Topical Meeting on Optical Computing held in Salt Lake City, Utah, in March 1995. This introduction provides a brief historical account of the series of optical computing meetings and a brief review of the papers contained in this special issue.     

Optical implementation of visible gray-image morphology with the visual-area-coding technique

We present a novel scheme of visible gray-image morphology with the visual-area-coding technique (VACT). The VACT is a technique of digitized analog-optical computing in which data are converted into visible coded patterns and processed with the visible form. Because the achievable operations in the VACT are identical to those of mathematical morphology, mathematical morphology is adapted to gray-image morphology with the VACT. Computer simulation and optical experiments of the several operations in mathematical morphology verify the correctness of the proposed technique. The processing capacity of the proposed method is estimated in terms of the space-bandwidth product.     

Simultaneous bipedal locomotion based on haptics for teleoperation

ABSTRACT

This paper proposes a novel, simultaneous bipedal locomotion method using haptics for remote operation of biped robots. In general, traditional biped walking methods require very high computational power and advanced controllers to perform the required task. However, in this proposed method, a master exoskeleton attached to the human’s lower body is used to obtain the trajectory and haptic information to generate the trajectory of the slave biped robot in real time. Lateral motion of the center of mass of the biped is constrained in this experiment. Also, it is considered that no communication delay is presented in between the two systems in this experiment, and they are not discussed in this paper. Since a direct motion transmission is used in the proposed method, this method is quite straight forward and a simultaneous walking can be realized at the same time with high performance. Also, it does not require an exact dynamic model of the biped or specific method to plan the trajectory. The gait pattern of the biped is directly determined by that of the human. Also, the operator can feel the remote environment through the exoskeleton robot. Results obtained from the experiments validate the proposed method.     

Surface-collection efficiency of Nuclepore filters for nanoparticles

The flat surface of Nuclepore filters is suitable for observing collected particles with a scanning electron microscope (SEM). However, experimental data on surface-collection efficiency are limited because surface-collection efficiencies cannot be measured directly using aerosol measuring instruments. In this study, the surface-collection efficiencies of Nuclepore filters were determined by establishing the ratio of the number of particles deposited on the surface of the filter visually counted with an SEM to the number of inflow particles counted by a condensation particle counter, using monodispersed polystyrene latex particles (30–800 nm) and silver particles (15–30 nm). Because Nuclepore filters with smaller pore sizes would be expected to produce higher minimum surface-collection efficiency and a higher pressure-drop, 0.08 and 0.2 µm Nuclepore filters were chosen as the test filters in view of both collection efficiency and pressure drop. The results showed that the minimum surface-collection efficiencies of the 0.08 µm pores at face velocities of 1.9 and 8.4 cm·s^?1 were approximately 0.6 and 0.7, respectively, and those of the 0.2 µm pores at face velocities of 1.5 and 8.6 cm·s^?1 were approximately 0.8 and 0.6, respectively. Because the pressure drop of the 0.2 µm pore filter was lower than that of the 0.08 µm pore filter under the same flow-rate conditions, the 0.2 µm pore filter would be more suitable considering the pressure drop and collection efficiency. The obtained surface collection efficiencies were quantitatively inconsistent with theoretical surface-collection efficiencies calculated using conventional theoretical models developed to determine the collection efficiency of filters with larger pores.

© 2016 American Association for Aerosol Research     

Aerosol Particle Collection Efficiency of Holey Carbon Film-Coated TEM Grids

A simple sampling method to collect aerosol particles for transmission electron microscope (TEM) analysis was developed by R’mili and others in 2013. The method involves passing air through a holey carbon film-coated copper mesh TEM grid (holey carbon grid) and sampling particles by filtration. In this study, we proposed a modified calculation method to represent the collection efficiencies of holey carbon grids, taking into consideration the porosity of the copper mesh. We then evaluated the particle collection efficiencies of holey carbon grids both theoretically and experimentally. We tested the collection efficiency of two types of holey carbon grids, with nominal pore sizes of 1.2 and 0.6 μm, using particles of monodispersed polystyrene latex (PSL) and potassium chloride. The overall collection efficiency of each grid (E_grid) was determined by the downstream/upstream concentration ratio measured by condensation particle counters (CPCs). In addition, for PSL particles, the collection efficiency of the holey carbon film (E_film) was determined by the ratio of the number of particles on the film (counted on a scanning electron microscope) to the number of inflow particles (counted by a CPC). We compared model calculations against the experimental results obtained in this study and those reported by R’mili and others in 2013. These data showed that the calculated E_grid values were in reasonably good agreement with the experimental E_grid values. However, although the model calculation indicated that E_film ≈ E_grid, there was an inconsistency between the experimental E_film and E_grid, which requires further investigation in order to determine its cause.

Copyright 2014 American Association for Aerosol Research     

Neuromelanin in Parkinson’s Disease: Tyrosine Hydroxylase and Tyrosinase

Parkinson’s disease (PD) is an aging-related disease and the second most common neurodegenerative disease after Alzheimer’s disease. The main symptoms of PD are movement disorders accompanied with deficiency of neurotransmitter dopamine (DA) in the striatum due to cell death of the nigrostriatal DA neurons. Two main histopathological hallmarks exist in PD: cytosolic inclusion bodies termed Lewy bodies that mainly consist of α-synuclein protein, the oligomers of which produced by misfolding are regarded to be neurotoxic, causing DA cell death; and black pigments termed neuromelanin (NM) that are contained in DA neurons and markedly decrease in PD. The synthesis of human NM is regarded to be similar to that of melanin in melanocytes; melanin synthesis in skin is via DOPAquinone (DQ) by tyrosinase, whereas NM synthesis in DA neurons is via DAquinone (DAQ) by tyrosine hydroxylase (TH) and aromatic L-amino acid decarboxylase (AADC). DA in cytoplasm is highly reactive and is assumed to be oxidized spontaneously or by an unidentified tyrosinase to DAQ and then, synthesized to NM. Intracellular NM accumulation above a specific threshold has been reported to be associated with DA neuron death and PD phenotypes. This review reports recent progress in the biosynthesis and pathophysiology of NM in PD.