Detail-preserving fluid control

We propose a new fluid control technique that uses scale-dependent force control to preserve small-scale fluid detail. Control particles define local force fields and can be generated automatically from either a physical simulation or a sequence of target shapes. We use a multi-scale decomposition of the velocity field and apply control forces only to the coarse-scale components of the flow. Small-scale detail is thus preserved in a natural way avoiding the artificial viscosity often introduced by force-based control methods. We demonstrate the effectiveness of our method for both Lagrangian and Eulerian fluid simulation environments.     

Microstructural characterization of U-7Mo/Al-Si alloy matrix dispersion fuel plates fabricated at 500 °C

The starting microstructure of a dispersion fuel plate will impact the overall performance of the plate during irradiation. To improve the understanding of the as-fabricated microstructures of U-Mo dispersion fuel plates, particularly the interaction layers that can form between the fuel particles and the matrix, scanning electron microscopy (SEM) and transmission electron microscopy (TEM) analyses have been performed on samples from depleted U-7Mo (U-7Mo) dispersion fuel plates with either Al-2 wt.% Si(Al-2Si) or AA4043 alloy matrix. It was observed that in the thick interaction layers, U(Al, Si)3 and U6Mo4Al43 were present, and in the thin interaction layers, (U, Mo) (Al, Si)3, U(Al, Si)4, U3Si3Al2, U3Si5, and possibly USi-type phases were observed. The U3Si3Al2 phase contained some Mo. Based on the results of this investigation, the time that a dispersion fuel plate is exposed to a relatively high temperature during fabrication will impact the nature of the interaction layers around the fuel particles. Uniformly thin, Si-rich layers will develop around the U-7Mo particles for shorter exposure times, and thicker, Si-depleted layers will develop for the longer exposure times.     

Trends in the core literature on tropical medicine: a bibliometric analysis from 1952-2002

Summary We present empirical data on frequency and pattern of misprints in citations to twelve high-profile papers. We find that the distribution of misprints, ranked by frequency of their repetition, follows Zipf's law. We propose a stochastic model of citation process, which explains these findings, and leads to the conclusion that about 70-90% of scientific citations are copied from the lists of references used in other papers.     

Primary extranodal lymphogranulomatosis of the flexura dodenal-jejunalis

A primary extranodal lymphogranuloma of Hodgkin was found in the small bowel (PS II AE) of a 34-year-old man. Two years after radical surgery followed by local telecobalt therapy, the patient is in good health. The symptomatology, therapy and prognosis of this rare form of Hodgkin's lymphogranuloma are briefly reviewed.     

Interference canceller for a single-wavelength bidirectional optical-fibre link

A simple and practical electronic technique is presented that provides interchannel-crosstalk isolation to better than a 10?9 BER for a 20 Mbit/s single-wavelength single-fibre full-duplex transmission system.     

A comparison of three microindentation hardness scales at low and ultralow loads

Indentation hardness tests were performed on thick, fine-grained, electro-formed deposits of copper and nickel using Knoop, Vickers, and Berkovich indenters. The latter type of indenter was used for shallow penetrations (85–1750nm), and results are reported in terms of nanoscale hardness (NH) numbers. Knoop and Vickers indenters were used with applied loads of between 0.15 and 0.98 N, and at the lowest load, produced indentation depths comparable to the larger ones obtained with the Berkovich indenter. The NH numbers became very sensitive to penetration depth when the penetration depth was less than certain critical values. NH numbers for Cu and Ni were higher than those for Knoop and Vickers testing at comparable penetration depths. Applying indenter area function corrections to calculate hardness numbers (i.e., considering projected area versus facet contact area) resulted in a closer correlation between microhardness and nanohardness scales; however, changes in the tip shape because of wear or other imperfections can lead to inaccurate calculation of NH numbers at the lowest loads. Results also suggest that the interconversion of lowload hardness numbers from one scale to another can be material-dependent.