Call admission control schemes: a review

Over the last few years, a substantial number of call admission control (CAC) schemes have been proposed for ATM networks. We review the salient features of some of these algorithms. Also, we quantitatively compare the performance of three of these schemes     

Fatigue Behavior of a Pavement Foundation with Recycled Aggregate and Waste HDPE Strips

A laboratory investigation was conducted to evaluate the fatigue behavior of an alternative pavement foundation material containing cement stabilized reclaimed crushed aggregate. Class C fly ash, and waste-plastic strip [high density polyethylene (HDPE)] reinforcement. The primary motivation for this research was to evaluate a composite that contained more than 90% recycled materials for use as an alternative foundation layer underneath conventional flexible or rigid pavement. The specific objectives of this study were (1) to evaluate the flexural fatigue behavior of the new composite, and (2) to evaluate the accumulation of fatigue damage in the material. The results indicate that the fatigue resistance of this material is similar to other traditional stabilized pavement materials. It was found that the dynamic elastic modulus remained approximately constant (degraded slowly) for most specimens up to the end of fatigue life. Fatigue damage computed using a dissipated energy approach showed that the damage accumulation in this material approximately follows Miner's rule for cumulative damage, which is often used in pavement engineering.     

Bayes and classical estimation of environmental factors for thebinomial distribution

An environmental factor converts reliability test results at one environmental condition into equivalent “failure” information at other environments. This paper studies environmental-factor estimation for the binomial distribution. Under general conditions, Bayes point estimates and credibility limits for environmental factors are derived. Classical point and confidence interval estimates are introduced and compared with the Bayes estimators. The characteristics of Bayes and classical estimators for the binomial distribution are summarized through numerical computation and theoretical analysis. A numerical example of reliability assessment by means of environmental factors is presented     

An investigation of pore cracking in titanium welds

Two welded Ti-6A1-4V pressure vessels leaked prematurely in service. The leaks were caused by cracks emanating from weld porosity. The cracks originated during fabrication, with subsequent growth in service leading to the formation of the leak paths. Pore cracking is thought to be caused by a mechanism that involves both sustained-load and cyclic contributions, with the former being the more prominent. It is shown that the tendency for cracking is influenced by pore position and that pore size is not a deciding factor in that regard. The factors that govern pore cracking are discussed, and the possible role of interstitial embrittlement is assessed.     

50-nm Self-Aligned and “Standard” T-gate InP pHEMT Comparison: The Influence of Parasitics on Performance at the 50-nm Node

Continued research into the development of III-V high-electron mobility transistors (HEMTs), specifically the minimization of the device gate length, has yielded the fastest performance reported for any three terminal devices to date. In addition, more recent research has begun to focus on reducing the parasitic device elements such as access resistance and gate fringing capacitance, which become crucial for short gate length device performance maximization. Adopting a self-aligned T-gate architecture is one method used to reduce parasitic device access resistance, but at the cost of increasing parasitic gate fringing capacitances. As the device gate length is then reduced, the benefits of the self-aligned gate process come into question, as at these ultrashort-gate dimensions, the magnitude of the static fringing capacitances will have a greater impact on performance. To better understand the influence of these issues on the dc and RF performance of short gate length InP pHEMTs, the authors present a comparison between In_0.7Ga_0.3As channel 50-nm self-aligned and "standard" T-gate devices. Figures of merit for these devices include transconductance greater than 1.9 S/mm, drive current in the range 1.4 A/mm, and fT up to 490 GHz. Simulation of the parasitic capacitances associated with the self-aligned gate structure then leads a discussion concerning the realistic benefits of incorporating the self-aligned gate process into a sub-50-nm HEMT system     

A Simple Quasi-2D Numerical Model of a Thermogage Furnace

A simple quasi-2D model for the temperature distribution in a graphite tube furnace is presented. The model is used to estimate the temperature gradients in the furnace at temperatures above which contact sensors can be used, and to assist in the redesign of the furnace heater element to improve the temperature gradients. The Thermogage graphite tube furnace is commonly used in many NMIs as a blackbody source for radiation thermometer calibration and as a spectral irradiance standard. Although the design is robust, easy to operate and can change temperature rapidly, it is limited by its effective emissivity of typically 99.5–99.8%. At NMIA, the temperature gradient along the tube is assessed using thermocouples up to about 1,500°C, and the blackbody emissivity is calculated from this. However, at higher operating temperatures (up to 2,900°C), it is impractical to measure the gradient, and we propose to numerically model the temperature distributions used to calculate emissivity. In another paper at this conference, the model is used to design an optimized heater tube with improved temperature gradients. In the model presented here, the 2-D temperature distribution is simplified to separate the axial and radial temperature distributions within the heater tube and the surrounding insulation. Literature data for the temperature dependence of the electrical and thermal conductivities of the graphite tube were coupled to models for the thermal conductivity of the felt insulation, particularly including the effects of allowing for a gas mixture in the insulation. Experimental measurements of the temperature profile up to 1,500°C and radial heat fluxes up to 2,200°C were compared to the theoretical predictions of the model and good agreement was obtained.     

On an evolutionary approach for constrained optimization problem solving

Over the last few decades, many different evolutionary algorithms have been introduced for solving constrained optimization problems. However, due to the variability of problem characteristics, no single algorithm performs consistently over a range of problems. In this paper, instead of introducing another such algorithm, we propose an evolutionary framework that utilizes existing knowledge to make logical changes for better performance. The algorithmic aspects considered here are: the way of using search operators, dealing with feasibility, setting parameters, and refining solutions. The combined impact of such modifications is significant as has been shown by solving two sets of test problems: (i) a set of 24 test problems that were used for the CEC2006 constrained optimization competition and (ii) a second set of 36 test instances introduced for the CEC2010 constrained optimization competition. The results demonstrate that the proposed algorithm shows better performance in comparison to the state-of-the-art algorithms.     

Fabrication of an optically driven pH gradient generator based on self-assembled proton pumps

Optically manipulating the local pH of a target solution in a microchannel, or reservoir, provides a mechanism for activating and controlling a variety of biological and chemical processes on Lab-on-a-Chip (LOC) devices and micro-total analysis systems (μ-TAS). A microscale pH gradient generator that exploits the light-activated molecular proton pumps found in the purple membranes (PM) of bacteriorhodopsin is described in this paper. The photo-electro-chemical transducer is an ultrathin layer (~13?nm) of oriented PM patches self-assembled on an Au-coated porous substrate. A biotin labeling and streptavidin molecular recognition technique is used to ensure that the extracellular side of all PM patches is attached to the porous substrate enabling unidirectional and efficient transport of ions across the transducer surface. The photo-induced proton pumps generate a flow of ions that produce a measurable change in pH between the separated solutions. The self-assembly procedure is experimentally quantified based on the capacitance characteristics of the bR membranes. The investigation confirms that the transducer is covered with the bR proton pumps at a mass density of 2.33?ng/cm². Experimental tests also show that the proposed transducer can repeatedly generate pH gradients as high as 0.42 and absolute voltage differences as high as 25?mV when illuminated by an 18?mW, 568?nm light source. Furthermore, the ΔpH is observed to be nonlinear with respect to light intensity and exposure time. The ΔpH of the target solution is sufficient to cause a phenolphthalein indicator dye to change color or an ionic hydrogel micro-valve to expand.