Feasibility study of large-scale mass customization 3D printing framework system with a case study on Nanjing Happy Valley East Gate

At present, the development and implementation of digital transformation are the keys to promoting high-quality industry development. The new digital fabrication method of robotic 3D printing is a research area being studied by many to tackle the issue of the declining productivity of traditional construction methods. Although many studies have been done, most of the current 3D printing projects are facing limitations in terms of scale. In order to bridge the gap, this article proposed a mass customization 3D printing framework system for large-scale projects. This article discusses how mass customization is made possible through the joint operation of the FUROBOT software and 3D printing hardware. By taking the east gate of Nanjing Happy Valley Plaza as a case study, the article demonstrates and studies the feasibility of the large-scale mass customization 3D printing framework system.     

燃煤锅炉除尘专用滤料的开发

介绍机械制造厂燃煤锅炉的烟尘特点,分析滤料失效的原因,提出一套针对该工况的滤料解决方案。介绍针对复杂工况条件所选用的纤维种类以及复合面层原料成分配比的确定,最终选用针刺工艺加工并对该新产品的基本性能进行了测试分析。     

一种5 重real-time PCR筛查转基因水稻方法的建立

以转基因水稻中最常用的CaMV35S启动子、NOS终止子、Cry1Ab/Ac基因、HPT基因及SPS水稻内标基因为研究对象，利用5 种不同的荧光信号（FAM、HEX、Taxas Red、Cy5、Cy5.5）进行多重实时聚合酶链式反应（real-time polymerase chain reaction，real-time PCR）检测方法的研究。通过引物组合筛选、反应体系优化、特异性测试、灵敏度测试、适用性测试等一系列实验，建立了5 重real-time PCR方法，灵敏度可达0.032%。此方法具有灵敏度高、结果准确、通量大等优点，可实现水稻中转基因成分的快速、高效检测。     

CMOS光接收机主放大器设计

利用CMOS工艺设计一种用于SDH STM 4速率级(622 Mb/s)光纤用户网的光接收机放大电路。此电路由输入/输出缓冲、主放大单元、偏置补偿电路4部分组成。通过直接耦合技术提高增益,降低功耗;利用有源电感负载提高系统带宽。采用商用SmartSpice电路仿真软件和CSMC HJ 0.6μm工艺参数对该电路进行仿真。结果表明,该电路在5 V工作电压下中频增益为81 dB,3 dB带宽为470 MHz。     

基于ARM微处理器的故障记录系统

给出了在普通数据采集基础上的故障记录系统的设计方案,利用ARM微处理器实现了模拟信号较完整的故障波形记录和开关信号的事件顺序记录(SOE)。对LPC2106ARM系列处理器、ADS7871模/数转换器以及数据通信接口等内容进行了讨论,阐述了系统的工作原理、软件处理方式、系统通信。该设计方案电路简单,特别适用于电力系统。     

In-situ composite Cu-Cr contact cables with high strength and high conductivity

In order to develop a new type of contact cable with high strength and high electrical conductivity, Cu-Cr alloy series were selected as materials and Cu-Cr alloy castings were produced by means of directional solidification continuous casting (DSCC) process. The results show that the fibrillar strengthening phase, 13-Cr, orderly arranges among the copper matrix phase along the wire direction; and a microstructure of in-situ composite forms, which retains the basic property of good conductivity of the copper matrix and meanwhile obtains the strengthening effect of [3-Cr phase. The production technology as well as the mechanical property, electrical property, and synthetic property of the in-situ composite contact cables was discussed.     

基于FAX／40E电话语音／传真卡的通信技术研究

以一个基于 FAX/ 40 E电话语音 /传真卡技术的传真系统为例 ,重点研究 FAX/ 40 E电话语音 /传真卡技术与计算机之间的通信技术 ,并讨论有关多线程技术问题。     

络合沉淀法制备BaTiO_3超细粉末

在分析ＢａＴｉＯ_３前驱体形成机理的基础上，提出了以草酸作为络合剂，用络合沉淀法制备超细ＢａＴｉＯ_３新工艺。用化学分析法测定产物Ｂａ／Ｔｉ比，用ＸＲＤ、ＴＥＭ、ＢＩ－９０激光散射粒度仪对产物的晶型、粒度及形貌进行表征。结果表明：采用该法合成的前驱体，微观组分确定，粒径小，粒度分布窄，近似球形，煅烧后为高纯超细ＢａＴｉＯ_３粉末。     

油气两相压降数值试井模型及其典型曲线的规律

提出油气两相流动压降试井数字模型的数值解法，用此解法对均质油藏中油气两相流动试井的规律进行了研究，根据实例计算结果，分析油气两相流下典型压降试井曲线的特征，以及油、气的初始饱和度分布，两相黏度比，饱和度梯度、相对渗透率关系对试井曲线的影响和相应的作用机理，首次发现气体的存在会使油气两相试井的压力导数曲线表现出类似于单相流双重介质试井的压力导数曲线的“下凹”特征。