Rate of ammonia oxidation in a synthetic saline wastewater by a nitrifying mixed‐culture

Most of the kinetic studies on nitrification have been performed in diluted salts medium. In this work, the ammonia oxidation rate (AOR) was determined by respirometry at different ammonia (0.01 and 33.5 mg N‐NH₃ L^?1), nitrite (0–450 mg N‐NO₂^? L^?1) and nitrate (0 and 275 mg N‐NO₃^? L^?1) concentrations in a saline medium at 30 °C and pH 7.5. Sodium azide was used to uncouple the ammonia and nitrite oxidation, so as to measure independently the AOR. It was determined that ammonia causes substrate inhibition and that nitrite and nitrate exhibit product inhibition upon the AOR. The effects of ammonia, nitrite and nitrate were represented by the Andrews equation (maximal ammonia oxidation rate, r_AOMAX, = 43.2 [mg N‐NH₃ (g VSS_AO h)^?1]; half saturation constant, K_SAO, = 0.11 mg N‐NH₃ L^?1; inhibition constant K_IAO, = 7.65 mg N‐NH₃ L^?1), by the non‐competitive inhibition model (inhibition constant, K_INI, = 176 mg N‐NO₂^? L^?1) and by the partially competitive inhibition model (inhibition constant, K_INA, = 3.3 mg N‐NO₃^? L^?1; α factor = 0.24), respectively. The r_AOMAX value is smaller, and the K_SAO value larger, than the values reported in diluted salts medium; the K_IAO value is comparable to those reported. Process simulations with the kinetic model in batch nitrifying reactors showed that the inhibitory effects of nitrite and nitrate are significant for initial ammonia concentrations larger than 100 mg N‐NH₄⁺ L^?1. Copyright © 2005 Society of Chemical Industry     

EXPERIMENTAL STUDY ON MIXING: POWER CONSUMPTION AND DEGREE OF SUSPENSION

An experimental study on mixing, degree of suspension and power consumption in solid-liquid suspensions was done. A system similar to those found in anaerobic fermentation processes of animal manures was used, and an existing mixing equipment was adapted for the study. Power consumption and degree of suspension for both mechanical mixing and mixing by gas was determined. The influence of variables such as geometry, solids concentration, stirrer velocity, and gas velocity was studied, discussed, and compared to data from the literature. Best results were obtained for gas mixing, the power consumption being about one fourth of that required by mechanical agitation. Finally, extended correlations relating Power and Reynolds numbers for mechanical mixing and mixing by gas are proposed.     

Correlation of the loss in photovoltaic module performance with the ageing behaviour of the backsheets used

The influence of the type of backsheet on the electrical performance of test modules was evaluated before and after increasing time of accelerated ageing (damp heat [DH] exposure). Besides the measurement of the electrical power of the modules and the performance of the cells by electroluminescence, the ageing‐induced changes within the polymeric encapsulate and backsheets were investigated by means of vibrational spectroscopy and by thermo analytical methods. In addition, the permeability of the backsheets in the original and aged state was determined. This wide set of test parameters and methods allowed for the detection of correlations between (i) physical and chemical properties as well as their ageing‐induced changes of the materials and (ii) the module performance. A clear dependence of the relative loss in power output upon exposure under DH conditions for 2000 h could be observed for a set of identical test modules varied in composition only in the type of back cover used. While the modules containing gas‐tight backsheets and glass experienced only little loss in the relative power output, some modules with permeable backsheets showed a significant relative decrease in the power output and fill factor in dependence of the backsheet type used. Cell degradation could be visualised by recording electroluminescence images before and after the accelerated ageing test. The permeation properties of the backsheet used and their ageing‐induced changes seem to have an influence on the module performance. However, the absolute values neither of the water vapour transmission rate (WVTR) nor of the oxygen transmission rate (OTR) are directly linked to the loss in power output upon accelerated ageing under DH conditions. It could be shown that the ageing‐induced changes (relative transmission rates) between WVTR and OTR can be correlated with the module performance. These ageing‐induced changes in the permeation behaviour of the backsheets can be explained by (i) physical changes (e.g. post‐crystallisation, changes in the crystal structure or the crystalline microstructure) and (ii) chemical ageing effects such as a decrease in the molecular mass of the polyester (PET) polymer chains because of hydrolytic polymer degradation leading to a change in the crystallisation behaviour of PET. Hydrolytic degradation (= chemical ageing) of the PET core layer was observed (with varying extent) for all PET‐based backsheets and can, thus, not be directly correlated with the loss in performance of the corresponding test modules. The physical ageing effects, however, were detected only for those backsheets showing (i) strong deviating changes in the relative permeation rates for oxygen and water vapour upon accelerated ageing and (ii) a clear loss in electrical performance. Copyright © 2015 John Wiley & Sons, Ltd.     

平板显示器制造中用作精密淀积设备的喷墨印刷头

显示器设备制造商之间有着共同的发展计划,电子流体显色剂和喷墨印刷头的设计者们已成功实现了大型电子显示板平板显示器引导线制造中特制的喷墨印刷头的发展计划。这种喷墨印刷头正在被认作各种大面积液晶显示器制造工艺的精密淀积设备。现这种喷墨型设备的市场需求正在不断增长。对于通过单独整理每个喷嘴通道进行一个128喷嘴的压力式喷墨印刷头流体下降位置控制情况给予了介绍。这种印刷头用作大型电子显示板显示器引导线的制造,通过采用不同的印刷头便可使大面积衬底的生产率得到提高的机会。讨论了通过印刷头和系统设计提高生产率实质。其它的高技术市场为利用精密降落位置和降落量控制。并给出了采用喷嘴制作印刷电路极的一些例子。     

Antifreeze Proteins: Novel Applications and Navigation towards Their Clinical Application in Cryobanking

Antifreeze proteins (AFPs) or thermal hysteresis (TH) proteins are biomolecular gifts of nature to sustain life in extremely cold environments. This family of peptides, glycopeptides and proteins produced by diverse organisms including bacteria, yeast, insects and fish act by non-colligatively depressing the freezing temperature of the water below its melting point in a process termed thermal hysteresis which is then responsible for ice crystal equilibrium and inhibition of ice recrystallisation; the major cause of cell dehydration, membrane rupture and subsequent cryodamage. Scientists on the other hand have been exploring various substances as cryoprotectants. Some of the cryoprotectants in use include trehalose, dimethyl sulfoxide (DMSO), ethylene glycol (EG), sucrose, propylene glycol (PG) and glycerol but their extensive application is limited mostly by toxicity, thus fueling the quest for better cryoprotectants. Hence, extracting or synthesizing antifreeze protein and testing their cryoprotective activity has become a popular topic among researchers. Research concerning AFPs encompasses lots of effort ranging from understanding their sources and mechanism of action, extraction and purification/synthesis to structural elucidation with the aim of achieving better outcomes in cryopreservation. This review explores the potential clinical application of AFPs in the cryopreservation of different cells, tissues and organs. Here, we discuss novel approaches, identify research gaps and propose future research directions in the application of AFPs based on recent studies with the aim of achieving successful clinical and commercial use of AFPs in the future.     

Modelling of polymerization kinetics and molar mass development in the nitroxide-mediated polymerization (NMP) of styrene in supercritical carbon dioxide using the PC-SAFT equation of state

A mathematical model for polymerization kinetics and molar mass development in the nitroxide-mediated polymerization (NMP) of vinyl monomers in supercritical carbon dioxide (scCO₂) has been developed. The method of moments is used for molar mass development. The perturbed-chain statistical associating fluid theory (PC-SAFT) equation of state is used to estimate the number of stable phases present at equilibrium in the reaction mixture, critical number average chain length at which polymer particles are formed, and monomer concentration in each phase. Pure and binary PC-SAFT interaction parameters are estimated from liquid–liquid equilibrium (LLE) and liquid–vapour equilibrium (LVE) experimental data at 60 to 129°C. The effect of pressure on monomer conversion and molar mass development in the polymerization of styrene (Sty) using benzoyl peroxide (BPO) and 2,2,6,6-Tetramethylpiperidinyl-1-oxyl (TEMPO) at 120°C and 300–500 bar is studied. It was observed that increasing pressure increases polymerization rate without significantly affecting molar mass development.     

Interlaboratory study on lipid oxidation during accelerated storage trials with rapeseed and sunflower oil analyzed by conjugated dienes as primary oxidation products

Accelerated storage tests are frequently used to assess the oxidative stability of foods and related systems due to its reproducibility. Various methods and experimental conditions are used to measure lipid oxidation. Differences between laboratories make it necessary to determine the repeatability and reproducibility of oxidation tests performed under the same conditions. The objective of the present interlaboratory study was to evaluate the outcome of a storage test for two different bulk oils, sunflower oil (SFO) and rapeseed oil (RSO), during a period of 9 weeks at 20°C, 30°C, 40°C, and 60°C. Sixteen laboratories were provided with bottled oils and conducted the storage tests according to a detailed protocol. Lipid oxidation was monitored by the formation of conjugated dienes (CD) and the activation energy (E_a) was determined for comparative purposes and statistically evaluated. An increase in CD formation was observed for both oils when the storage temperature was increased in all laboratories. The E_a,1 ranged from 47.9 to 73.3 kJ mol⁻¹ in RSO and from 27.8 to 62.6 kJ mol⁻¹ in SFO, with average values of 58.2 and 46.8 kJ mol⁻¹, respectively. The reproducibility coefficients were 10.9% and 18.2% for RSO and SFO, respectively. Practical applications: In order to compare results on oxidative stability of foods derived from different studies, the reproducibility of storage tests and methods employed to evaluate the oxidation level should be considered. This study provides fundamental data on the reproducibility of lipid oxidation under accelerated storage conditions and defines important parameters to be considered for the conduction of experiments.     

Functionalization of Polymer Surfaces Using Excimer VUV Systems and Silent Discharges. Application to Electroless Metallization

New approaches for electroless plating of nonconductive polymers or polymer-based materials are described. In this work, polyimide substrates were surface-functionalized (i) in nitrogenated (ammonia at reduced pressure) and oxygenated (air at atmospheric pressure) atmospheres under assistance of vacuum-ultraviolet (VUV) irradiation (use of a xenon silent discharge excimer source) or (ii) directly in air at atmospheric pressure using a dielectric-barrier discharge (DBD) device. After functionalization, the substrates were “activated” by dipping in a dilute acidic PdCl₂ solution or by spin-coating of a thin metal-organic film (from a solution of palladium acetate (PdAc) in chloroform). The catalytic activity of the so-deposited palladium species toward the electroless deposition of nickel was studied before and after a VUV post-irradiation (in air at atmospheric or reduced pressure) with a view to understanding better the role of the reducer (sodium hypophosphite) within the electroless bath.

This work confirms the specific interest of grafting nitrogenated functionalities onto polymer surfaces for attaching covalently the palladium-based catalyst (in particular in the case of the PdCl₂ route), forming thus strong Pd - N - C bonds at the metal/polymer interface. This results from the strong chemical affinity of palladium toward nitrogen. On the other hand, when oxygenated functionalities are surface-grafted, the conventional two-step procedure using SnCl₂ and PdCl₂ solutions can be proposed due to the strong chemical affinity of tin toward oxygen. The Ni deposits obtained under these different conditions pass the standard Scotch^®-tape test and, therefore, exhibit a good practical adhesion. For this same purpose, it is interesting to note that the DBD treatment operating in air at atmospheric pressure causes an increase of the surface roughness and, therefore, an improvement in adhesion of metallic films when their initiation is catalyzed through the PdAc route. In addition, this work demonstrates that extensive research still has to be performed to understand and improve the Ni/polymer adhesion when the PdAc route associated with a VUV irradiation is considered.     

Effect of nanocellulose fibers and acetylated nanocellulose fibers on properties of poly(ethylene‐co‐vinyl acetate) foams

Cellulose nanofibers are promising materials in the development of polymeric foams, because they act as heterogeneous nucleation sites for the growth of cells during foaming. In this research, we studied the incorporation of cellulose nanoparticles in poly(ethylene‐co‐vinyl acetate)‐EVA foams. The foams were produced with different fiber contents. We observed the effect of a chemical treatment by acetylation on the cellulose fibber, that is, we evaluated the use of hydrophilic and hydrophobic cellulose nanofibers in EVA foams. The main results indicate that with the addition of only 1% of cellulose nanofibers, cell density significantly reduces when compared with the pure EVA foams. On the other hand, by increasing the cellulose content, the agglomeration of nanofibers also increases, which results in heterogeneous cell sizes. The same phenomenon was observed in the foams produced with acetylated cellulose nanofibers, regardless of the fiber content used. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44760.     

Chlorinated Polycyclic Aromatic Hydrocarbons Associated with Drinking Water Disinfection: Synthesis,Formation under Aqueous Chlorination Conditions and Genotoxic Effects

Polycyclic aromatic hydrocarbons (PAHs) are among the most persistent and toxic organic micropollutants present in water and several of them are mutagenic and carcinogenic. Although it has been shown that chlorinated derivatives of PAHs (Cl-PAHs) may be formed during the water chlorination procedure, little is known about their potential genotoxic and carcinogenic effects. The objectives of the present work were to prepare and characterize the major chlorinated derivatives of benzo[a]pyrene (BaP) and fluoranthene (Fluo), to develop an analytical methodology for their quantification in water samples and to analyse their potential genotoxicity. Chlorinated standards were prepared by a newly developed two phase method (water/n-hexane) using sodium hypochlorite. 6-Chloro-benzo[a]pyrene was selectively obtained from BaP, while 1,3-dichloro-fluoranthene and 3-chloro-fluoranthene were obtained from Fluo. All products were isolated and characterized by nuclear magnetic resonance and mass spectrometry. The formation of BaP- and Fluo-chlorinated derivatives under aqueous chlorination conditions was observed using a SPE-HPLC-FLD methodology. In addition, the cytotoxic and genotoxic activities of the three chlorinated derivatives were analyzed in comparison to their parent compounds, in a human-derived hepatoma cell line using the neutral red uptake and comet assays, respectively. The results showed that, at the equimolar doses of 100 and 125 μM, 6-Cl-BaP was able to induce a significantly higher level of DNA damage than BaP, suggesting a more potent genotoxic effect. In contrast, neither Fluo nor its chlorinated derivatives were genotoxic in the same cell line. The identification of new and possibly hazardous water chlorination by-product from PAHs emphasizes the need to minimize total organic carbon content of raw water and the implementation of safer water disinfection methods.