Evanescently coupled photodiodes integrating a double-stage taper for 40-Gb/s applications-compared performance with side-illuminated photodiodes

The design, fabrication, and performance of double-stage taper photodiodes (DSTPs) are reported. The objective of this work is to develop devices compatible with 40-Gb/s applications. Such devices require high efficiency, ultrawide band, high optical power handling capability, and compatibility with low-cost module fabrication. The integration of mode size converters improves both the coupling efficiency and the responsivity with a large fiber mode diameter. Responsivity of 0.6 A/W and 0.45 A/W are achieved with a 6-/spl mu/m fiber mode diameter and cleaved fiber, respectively, providing relaxed alignment tolerances (/spl plusmn/1.6 /spl mu/m and /spl plusmn/2 /spl mu/m, respectively), compatible with cost-effective packaging techniques. DSTPs also offer a wide bandwidth greater than 40 GHz and transverse-electric/transverse-magnetic polarization dependence lower than 0.2 dB. Furthermore, a DSTP saturation current as high as 11 mA results in optical power handling greater than +10 dBm and a high output voltage of 0.8 V. These capabilities allow the photodiode to drive the decision circuit without the need of a broad-band electrical amplifier. The DSTP devices presented here demonstrate higher responsivities with large fiber mode diameter and better optical power handling capabilities and are compared with classical side-illuminated photodiodes.     

Main-Chain Nematic Side-Chain Smectic Composite Liquid Crystalline Elastomers

A composite liquid crystalline elastomer is designed, combining main-chain and side-chain mesogenic polymers in the network, and resulting in micro-phase separated regions of nematic and smectic ordering in the macroscopically homogeneous elastomer. A range of different fractions of the components is explored, from fully nematic main-chain system, across to fully smectic side-chain elastomer. Thermal phase transitions of both phases coexisting in the material are detected by calorimetry, and the nematic/smectic structure investigated by X-ray scattering. The tensile stress–strain data reveal the key effect of such a multi-phase composite, where the nematic fraction adds ductility while the smectic fraction increases the modulus and mechanical stiffness. Varying the composition, the authors are able to optimize the mechanical properties of this material type.     

Experimental analysis of fuel from fish processing industry waste in a diesel engine

In the present work, biofuel derived from industrial fish processing industry waste is used in diesel engines to study its suitability . Biofuel from industry fish waste is produced through catalytic cracking, and its quality has been improved through distillation. A single cylinder 4.5 kW at 1500 rpm was used to find the suitability of biofuel and undistilled biofuel in diesel engine. Experimental results show that the brake thermal efficiency of biofuel and undistilled biofuel is similar. Brake thermal efficiency for diesel, undistilled biofuel and biofuel is 29.98, 32.12 and 32.4%, respectively, at 80% load. Carbon monoxide, unburnt hydrocarbons, particulate matter and oxides of nitrogen emissions increase with undistilled biofuel compared to biofuel. There is a small reduction in carbon dioxide emission with undistilled biofuel compared to biofuel. Even though the cylinder pressure is high with undistilled biofuel, the intensity of premixed combustion is lower than distilled biofuel. The ignition delay and combustion duration increase with undistilled biofuel. Finally, it is concluded that the fuel derived from fish processing industry waste can be used as a fuel for diesel engine after distillation.     

Relevance feedback revisited: dealing with content and structure in XML documents

Relevance feedback (RF) is a technique that allows to enrich an initial query according to the user feedback. The goal is to express more precisely the user’s needs. Some open issues arise when considering semi-structured documents like XML documents. They are mainly related to the form of XML documents which mix content and structure information and to the new granularity of information. Indeed, the main objective of XML retrieval is to select relevant elements in XML documents instead of whole documents. Most of the RF approaches proposed in XML retrieval are simple adaptation of traditional RF to the new granularity of information. They usually enrich queries by adding terms extracted from relevant elements instead of terms extracted from whole documents. In this article, we describe a new approach of RF that takes advantage of two sources of evidence: the content and the structure. We propose to use the query term proximity to select terms to be added to the initial query and to use generic structures to express structural constraints. Both sources of evidence are used in different combined forms. Experiments were carried out within the INEX evaluation campaign and results show the effectiveness of our approaches.     

Design and fabrication of a p-i-n photodiode with high responsivity and large alignment tolerances for 40-gb/s applications

This letter demonstrates an evanescently coupled p-i-n photodiode combined with a multimode diluted waveguide using a simple all 2-in InP processing that includes on-wafer mirrors etching and antireflection coating. A high responsivity of 0.81 A/W at 1.55 /spl mu/m with less than 0.4-dB polarization dependence and a large -1-dB vertical alignment tolerance of 2.70 /spl mu/m were achieved simultaneously with a bandwidth of 47 GHz. Stable operation for over 1000 h was obtained under bias stress and temperature at 200/spl deg/C.     

A comparative evaluation of filter-based feature selection methods for hyper-spectral band selection

Band selection (dimensionality reduction) plays an essential role in hyper-spectral image processing and applications. This article presents a unified comparison framework for systematic performance comparison of filter-based feature selection models and conducts a comparative evaluation of four methods: maximal minimal associated index (MMAIQ), mutual information-based max-dependency criterion (mRMR), relief feature selection (Relief-F), and correlation-based feature selection (CFS) for hyper-spectral band selection. The evaluation is based on the performance of effectiveness, robustness, and classification accuracy, which involves five measuring indices: class separability, feature entropy, feature stability, feature redundancy, and classification accuracy. Three images acquired by different sensors were used to investigate the performance of the metrics. Experimental results show the best results for MMAIQ for all data sets in terms of used measurements, except for feature stability where mRMR and Relief-F exhibit their superiority.     

Study of microstructure, phases and microhardness of metallic coatings deposited by flame thermal spray

The recharging technique by thermal spraying offers the opportunity of renovating the worn surface parts of a machine element to give it again a new technical life despite its previous degradation in service. This process has consequently interesting economic impacts. In order to improve the adherence between 100Cr6 steel deposits and the substrate material (left worn crankshafts), company SNC ATRA of Béjaïa uses at present a composite formed by (100Cr6 steel/molybdenum bond coat of 0.2 mm thick/crankshaft substrate). As a matter of fact, it is shown in the present work that the molybdenum bond coat is not appropriate since, for the 0.2 mm thickness, lateral cracks are observed in the middle of the bond coat. On the other hand, our experiment is that a deposit of 100Cr6 steel projected directly on the substrate seems more promising since no gaps or cracks were detected at the “deposit/substrate” interface of this two-material composite. Lastly, phase analysis using X-ray diffraction confirmed that during spraying process, a stable -phase (bcc) of 100Cr6 wire was transformed to a new phase of γ-phase (fcc). The coatings exhibited the higher microhardness which would contribute to increase wear resistance.     

High Gain × Bandwidth Product Over 140-GHz Planar Junction AlInAs Avalanche Photodiodes

This letter demonstrates a planar junction GalnAs-AlInAs avalanche photodiode using back-side illumination through thinned InP substrate covered with chemical vapor deposition SiN_x antireflection coating. The combined properties of very low dark current (I _dark(M = 0) = 17 nA), low excess noise factor (f(M = 10) = 3.5), and high gain x bandwidth product over 140 GHz were simultaneously achieved with a high primary responsivity of 0.95 A/W at 1.55 mum.     

Work stealing with private integer–vector–matrix data structure for multi‐core branch‐and‐bound algorithms

In this paper, the focus is put on multi‐core branch‐and‐bound algorithms for solving large‐scale permutation‐based optimization problems. We investigate five work stealing (WS) strategies with a new data structure called integer–vector–matrix (IVM). In these strategies, each thread has a private IVM allowing the local management of a set of subproblems enumerated using a factorial system. The WS strategies differ in the way the victim thread is selected and the granularity of stolen work units (intervals of factoradics). To assess the efficiency of the private IVM‐based WS approach, the five WS strategies have been extensively experimented on the flowshop scheduling permutation problem and compared with their conventional linked‐list‐based counterparts. The obtained results demonstrate that the IVM‐based WS outperforms the linked‐list‐based one in terms of CPU time, memory usage and number of performed WS operations. Copyright © 2016 John Wiley & Sons, Ltd.