An Adaptive Transmission Mode Selection Scheme for Cellular Underlaid D2D Communication

In this paper, we propose to use Artificial Bee Colony (ABC) optimization to solve the joint mode selection, channel assignment, and power allocation (JMSCPA) problem to maximize system throughput and spectral efficiency. JMSCPA is a problem where the allocation of channel and power depends on the mode selection. Such problems require two step solution and are called bi-level optimization problems. As bi-level optimization increases the complexity and computational time, we propose a modified version of single-level ABC algorithm aided with the adaptive transmission mode selection algorithm to allocate the cellular, reuse, and dedicated modes to the DUs along with channel and power allocation based on the network traffic load scenarios. A single variable, represented by the users (CUs and DUs) is used to allocate mode selection, and channel allocation to solve the JMSCPA problem, leading to a simpler solution with faster convergence, and significant reduction in the computational complexity which scales linearly with the number of users. Further, the proposed solution avoids premature stagnation of conventional ABC into local minima by incorporating a modification in its update procedure. The efficacy of the ABC-aided approach, as compared to the results reported in the literature, is validated by extensive numerical investigations under different simulation scenarios.

     

Effect of 100 KeV Ar+ ion beam irradiation on ZnO thin films – Influence of morphology vis-a-vis electrode/electrolyte interface and its impact on photoelectrochemical water splitting

The present study attempts quantitative determination of changes in the morphological surface features viz. fractal dimension, lower and upper cut off length scale through Power Spectral Density analysis prior to and after irradiation of 100 KeV Ar⁺ ion beam at incidence angles of 0°, 40° and 60° on ZnO thin films. All the unirradiated and irradiated samples are subjected to photoelectrochemical characterization and a correlation between photoelectrochemical performance and morphological parameters is established. Sample irradiated at 40° angle at the fluence of 5 × 10¹⁶ ions/cm² is found to possess maximum fractal dimension of 2.72, lower and upper cut off length scale of 3.16 nm and 63.00 nm respectively. This sample exhibits maximum photocurrent density of 3.19 mA/cm² and applied bias photon-to-current efficiency of 1.12% at 1.23 V/RHE. Hydrogen gas collected for duration of 1 h for the same sample was ~4.83 mLcm^?2.     

A prospective study of closure techniques of abdominal incisions in infants and children

In a prospective study of layered versus mass closure of abdominal incisions in infants and children, 34 cases underwent wound closure by layered and mass closure technique on an alternate basis. All the patients were assessed for their nutritional status and haemoglobin level pre-operatively, and wound complications were compared with respect to closure technique, nutritional status and normal haemoglobin level. Presence of protein energy malnutrition and anaemia did not increase the risk of wound complications with either of the technique.     

Corrosion characteristics of aluminium alloy graphite particulate composite in various environments

The present study was aimed at understanding the response of 2014 Al alloy dispersed with graphite particles in various corrosive environments. Marine (sodium chloride) as well as acidic media were selected for the purpose with a view to widen the range of utility of the composite for applications where such environments may be encountered. Studies were also extended to characterize the corrosion resistance of the composite in fresh as well as used lubricating oils to explore the possibilities of using it in bearing, bushing and such other applications. The corrosion behaviour of the base alloy processed under identical conditions was also examined in the above media to see the influence of graphite addition in the alloy. In order to assess the role of the matrix microstructure, the composite as well as the base alloy was subjected to corrosion in heat-treated as well as-cast conditions. It was observed that the specimens suffered from the maximum rate of corrosion in acid, while sodium chloride produced the minimum corrosion rate. Oil in both used and fresh conditions revealed a negligibly small extent of corrosion. The composite was found to show a higher rate of corrosion than the base alloy under identical test conditions. This was attributed to the dispersoid/matrix interfacial corrosion in the case of the graphitic aluminium alloy. Heat treatment of the composite and the base alloy was found to lower the rate of corrosion in the environments tested. Microstructural modifications of the matrix and possible relief of residual stresses were thought to be responsible for the lower rate of corrosion in the heat-treated condition.     

Analysis of a soliton-based logic module for a ring network

We analyze and numerically study the code-matching logic module that is the central element in a proposed soliton-based ring network system running at peak rates of 100 Gb/s. The proposed network is packet-switched, and fast logic is required to route each packet. That is the function of the code-matching logic module, and four soliton logic gates that can perform fast logic are the key devices in its design. The behavior of the code-matching logic module is governed by a large set of parameters, and we simulate it by varying many of these parameters. The physical effects that occur in these devices and their significance are analyzed. The results indicate that the logic module will work but within a restricted parameter range     

CARD: A Contact-based Architecture for Resource Discovery in Wireless Ad Hoc Networks

Traditional protocols for routing in ad hoc networks attempt to obtain optimal or shortest paths, and in doing so may incur significant route discovery overhead. Such approaches may be appropriate for routing long-lived transfers where the initial cost of route discovery may be amortized over the life of the connection. For short-lived connections, however, such as resource discovery and small transfers, traditional shortest path approaches may be quite inefficient. In this paper we propose a novel architecture, CARD, for resource discovery in large-scale wireless ad hoc networks. Our mechanism is suitable for resource discovery as well as routing very small data transfers or transactions in which the cost of data transfer is much smaller than the cost of route discovery. Our architecture avoids expensive mechanisms such as global flooding and complex hierarchy formation and does not require any location information. In CARD resources within the vicinity of a node, up to a limited number of hops, are discovered using a proactive scheme. For resources beyond the vicinity, each node maintains a few distant nodes called contacts. Contacts help in creating a small world in the network and provide an efficient way to query for distant resources. Using contacts, the network view (or reachability) of the nodes increases, reducing the discovery overhead and increasing the success rate. On the other hand, increasing the number of contacts also increases control overhead. We study such trade-off in depth and present mechanisms for contact selection and maintenance that attempt to increase reachability with reduced overhead. Our schemes adapt gracefully to network dynamics and mobility using soft-state periodic mechanisms to validate and recover paths to contacts. Our simulation results show that CARD is scalable and can be configured to provide desirable performance for various network sizes. Comparisons with other schemes show overhead savings reaching over 93% (vs. flooding) and 80% (vs. bordercasting or zone routing) for high query rates in large-scale networks.     

Stepwise-Graded Si3N4–SiC Ceramics with Improved Wear Properties

The processing of stepwise graded Si₃N₄/SiC ceramics by pressureless co-sintering is described. Here, SiC (high elastic modulus, high thermal expansion coefficient) forms the substrate and Si₃N₄ (low elastic modulus, low thermal expansion coefficient) forms the top contact surface, with a stepwise gradient in composition existing between the two over a depth of ∼1.7 mm. The resulting Si₃N₄ contact surface is fine-grained and dense, and it contains only 2 vol% yttrium aluminum garnet (YAG) additive. This graded ceramic shows resistance to cone-crack formation under Hertzian indentation, which is attributed to a combined effect of the elastic-modulus gradient and the compressive thermal-expansion-mismatch residual stress present at the contact surface. The presence of the residual stress is corroborated and quantified using Vickers indentation tests. The graded ceramic also possesses wear properties that are significantly improved compared with dense, monolithic Si₃N₄ containing 2 vol% YAG additive. The improved wear resistance is attributed solely to the large compressive stress present at the contact surface. A modification of the simple wear model by Lawn and co-workers is used to rationalize the wear results. Results from this work clearly show that the introduction of surface compressive residual stresses can significantly improve the wear resistance of polycrystalline ceramics, which may have important implications for the design of contact-damage-resistant ceramics.