Preparation of Mn2+-Cu+ co-doped P2O5–ZnO–Al2O3 glasses and their red fluorescence properties

To make a Mn²⁺-doped red glass phosphor that can be excited with ultraviolet (UV) light of light-emitting diodes (LEDs), 60P₂O₅-35ZnO-5Al₂O₃-8MnO-xCu₂O glasses (x = 0-1.00) were prepared by a melt-quenching method at 1200-1400°C for 30-180 minutes in atmospheric air, and the redox of Mn and Cu as well as fluorescence properties were investigated. The Mn²⁺ ion was not reduced and oxidized in the melting, quenching, and annealing processes. The valence of Cu in the glasses changed in the order of 0, 1+, and 2+ with the increase in the amount of Cu₂O and in the melting temperature and time. In this study, a 60P₂O₅-35ZnO-5Al₂O₃-8MnO-0.10Cu₂O glass melted at 1250°C for 90 minutes, having the highest Cu⁺ concentration, showed the strongest Mn²⁺ red fluorescence under the UV light at 275 nm. This strong Mn²⁺ red fluorescence has been caused by the energy transfer from excited Cu⁺ ions to Mn²⁺ ions.     

Unperturbed dimension of poly(4-acetoxystyrene) measured in good and theta solvents

In order to obtain the additional data concerning the unperturbed dimension of poly-4-substituted styrene, light scattering measurements are performed on the twenty-two fractions with molecular weight of (0.91–352)·10⁴ of poly(4-acetoxystyrene) in dioxan at 25°C, from which the molecular weight obtained was found easily to be evaluated with the gel permeation chromatography using THF. Phase separation experiments for this polymer indicate that the theta state is attained in isopropyl acetate at 19.7°C and butyl acetate at 26.8°C. By making viscosity measurements at that state, the value of K_Θ is directly evaluated as 5.4·10^?4 dl g^?1. The limiting viscosity number is also obtained in good solvents, THF and dioxan, at 25°C and constants of the Mark-Houwink-Sakurada equation in each solvent are determined. Further, approximately the same K_Θ as above is obtained from these data with the Stockmayer-Fixman plot. The calculated value of steric factor, 2.37, on this polymer may be plausible, compared with those of polyvinylaromatic derivatives.     

Fabrication of a poly-Si thin-film transistor with storage capacitor

The fabrication process of a low-temperature poly-Si thin-film transistor (TFT) with a storage capacitor was studied. The atmospheric-pressure chemical-vapour deposited SiO₂ protected the buried indium tin oxide (ITO) from reduction by a pure H₂ plasma treatment that was essential for the effective improvement of the poly-Si TFT characteristics. Thus, a storage capacitor with an ITO (picture electrode)-SiO₂-ITO (buried common electrode) structure was successfully fabricated. The poly-Si TFT with a channel width/length W/L ratio of 5 drove a 3 pF storage capacitor in 2 μs, and it showed superior driverability for LCD use. The TFT also had good hold characteristics under illumination for the realization of grey-scale representation.     

Effect of hydrogen charging on dislocation behavior in Ni-Cr and Ni<Subscript>2</Subscript>Cr alloys

The effects of hydrogen charging on the dislocation behaviour in Ni-Cr binary alloys have been investigated by means of transmission electron microscope (TEM) observations using single-crystalline specimens. The deformation mode of Ni-Cr alloys in the absence of hydrogen is characterized by planar dislocations. However, hydrogen charging changed the dislocation configurations to promote curved dislocations, such as dislocation loops and dipoles. The hydrogen-affected dislocation configurations are enhanced with increasing Ni content and reducing Cr content. Weak-beam images show that the Shockley partials of the hydrogen-affected dislocations frequently constrict to make kinks and cross-slip, as if the dislocations were generated by a thermally activated process. The effect of hydrogen charging on superdislocations of a Ni₂Cr superstructure has been also investigated using an aged 70Ni-30Cr alloy. While the deformation mode in the Ni₂Cr superlattice is classified as five variants of superdislocation triplets and one variant of ordinary dislocations, the hydrogen charging has preferred the ordinary dislocations to the superdislocation triplets. The results suggest that the charged hydrogen changes the local plasticity to affect the deformation dynamics in Ni-Cr alloys, where the influence of hydrogen on the plasticity is sensitive to the Ni/Cr concentration and the symmetry of atomic arrangement.     

Protein C Osaka 10 with aberrant propeptide processing: loss of anticoagulant activity due to an amino acid substitution in the protein C precursor

We studied the molecular basis of protein C deficiency in a family with a history of thromboembolic disease. An approximately 50% reduction in anticoagulant activity despite normal levels of protein C amidolytic activity and antigen was detected in plasma from the proband. All the exons and intron/exon junctions of the protein C gene were studied using a strategy that combined polymerase chain reaction amplification with DNA sequencing of the amplified fragments. We identified a C-to-A change at nucleotide number 1387 of the protein C gene in the proband and his mother, and this mutant was designated protein C Osaka 10. The C-to-A change resulted in the substitution of Ser for Arg at position -1, which is the processing protease cleavage site. The mutant protein C was partially purified from plasma of the patient's mother using barium adsorption followed by ion-exchange column chromatography. It eluted at the same sodium chloride concentration as normal protein C, and thus gamma-carboxylation of the mutant protein appeared to be normal. The apparent molecular weight of this mutant protein C was the same as that of the normal protein on immunoblotting. Amino-terminal sequence analysis showed that the light chain of the mutant protein C had an additional Ser at position-1. Thus, the loss of anticoagulant activity of protein C Osaka 10 can be explained by alteration of the conformation of the Gla domain by the additional Ser in the mutant molecule.     

Analytical studies of four-inch pipe whip tests under BWR LOCA conditions

The purpose of pipe rupture studies in JAERI is to perform model tests on pipe whip, restraint behavior, jet impingement and jet thrust force, and to establish a computational method for analyzing these phenomena. This report presents the analytical results of 4-inch pipe whip tests under BWR LOCA conditions.Dynamic response analyses were performed using the general-purpose finite element program ADINA. The test pipe was modelled by straight beam elements and the four restraints were modelled by a single truss element. The analytical results were compared with the experimental results. Impact time and maximum total restraint force showed good agreement with experimental results. On the other hand, pipe strain and pipe deflection could not be predicted so well. The reason for this is that the sliding of the restraint during the pipe whip movement cannot be considered in the analyses.     

Protein modification by a Maillard reaction intermediate methylglyoxal. Immunochemical detection of fluorescent 5-methylimidazolone derivatives in vivo

Methylglyoxal (MG), an endogenous metabolite that increases in diabetes, is a common intermediate in nonenzymatic glycation (Maillard reaction) in vivo. Here we describe the immunochemical approach to the detection of MG adducts in proteins in vitro and in atherosclerotic lesions of human aorta in vivo. The reaction of protein (bovine serum albumin) with MG led to selective loss of arginine and lysine residues, accompanied by the formation of 5-methylimidazolone (N delta-(5-methylimidazolon-2-yl)ornithine) and imidazolysine (1,3-di-lysino-4-methylimidazole) derivatives, respectively. The anti-5-methylimidazolone antibody was prepared by immunizing rabbits with a MG-keyhole limpet hemocyanin conjugate and purifying the serum on an affinity gel prepared by covalent attachment of the 5-methylimidazolone derivative. The antibody cross-reacted with the proteins treated with not only MG but trioses, such as hydroxyacetone, dihydroxyacetone, and glyceraldehyde. The immunohistochemical analysis revealed that atherosclerotic lesions of human aorta contained 5-methylimidazolone derivatives whose distributions were identical to those of advanced glycation end products (AGEs) detected by the anti-AGE antibody.     

In-plane transport properties of Si/Si1-xGexstructure and its FET performance by computer simulation

Transport properties of ungated Si/Si_1-xGe_x are studied by an ensemble Monte Carlo technique. The device performance is studied with a quantum hydrodynamic equation method using the Monte Carlo results. The phonon-scattering limited mobility is enhanced over bulk Si, and is found to reach 23000 cm²/Vs at 77 K and 4000 cm²/Vs at 300 K. The saturation velocity is increased slightly compared with the bulk value at both temperatures. A significant velocity overshoot, several times larger than the saturation velocity, is also found. In a typical modulation-doped field-effect-transistor, the calculated transconductance for a 0.18 μm gate device is found to be 300 mS/mm at 300 K. Velocity overshoot in the strained Si channel is observed, and is an important contribution to the transconductance. The inclusion of the quantum correction increases the total current by as much as 15%     

A reconfigurable VLSI-based double-lens tracking camera

Watching and tracking an object while seeing a much wider view is one of advantages of the eye system. We proposed and developed a tracking camera system that mimics the eyes by using double-lens modules. In the system, a wide view is captured through the wide-lens module, while the target in it is tracked and magnified through the telescopic lens module. Electronic circuits for tracking control are implemented onto the reconfigurable VLSI or FPGA in order to embed the parallelism in the tracking algorithm into the hardware. A successfully developed FPGA-based prototype performs high-speed tracking at the video-rate. This work was present in part at the 12th International Symposium on Artificial Life and Robotics, Oita, Japan, January 25–27, 2007