Effects of Prior Annealing on the Spark Plasma Sintering of Nanostructured Y2O3 Powders

The effects produced by annealing Y₂O₃ nanopowders on their spark plasma sintering (SPS) behavior are systematically investigated in this work. It is found that the annealed powders display higher sinterability with respect to the as‐received ones. Indeed, the maximum densification level reached from pristine powders is about 97.5%, whereas density decreases when further increasing either the sintering temperature or the dwell time. In contrast, the density of SPS products obtained from pretreated powder monotonically increases with temperature and processing time, thus leading to fully dense materials in 30 min at 1050°C and 60 MPa. Correspondingly, it is found that the annealing treatment markedly inhibits grain coarsening during SPS. Thus, dense translucent samples with grain size below 100 nm can be attained from annealed powders. On the other hand, white‐opaque specimens with significantly coarser microstructures (up to 1‐μm‐sized grains) are obtained when pristine powders are directly processed under the same sintering conditions. Furthermore, it is observed that the annealing treatment of SPS samples in air allows for graphite contamination removal, whereas no improvement in term of light transmittance is produced.     

Thermal and thermoelastic properties of fast extrusion furnace (FEF) carbon black loaded SBR vulcanizates

The effect of FEF carbon black as filler on the thermal capacity c, diffusivity a, and thermal conductivity λ, of styrene butadiene rubber (SBR) composites in the temperature range 300–420 K was studied. The filler strongly increases the thermal diffusivity, whilst strongly decreasing the thermal capacity and the thermal conductivity (except at high FEF content ≥80 phr). The influence of the filler on the thermoelastic behaviour of the same composites was also investigated. It was found that the thermoelastic temperature change (ΔT) increased with carbon black concentration as well as the entropy change per unit extension.     

Simple and low-cost fabrication of PDMS microfluidic round channels by surface-wetting parameters optimization

Convenient for both biologists and MEMS designers, Polydimethylsiloxane (PDMS) polymer is intensively investigated for its biocompatibility, transparency, high resistance under plasma treatment, flexibility and resistance to high temperature. However, for microfluidic applications, the fabrication of PDMS circular channels is difficult to achieve except by wire moulding. In this article, we present a simple, fast and low-cost fabrication method which can be applied out of clean-room environment. It is based on the deposition of alginic acid sodium salt aqueous solution, enabling the formation of a liquid cylinder on the most hydrophilic part of a hydrophilic/hydrophobic patterned surface. We experimentally studied the interaction between liquid rivulets and surfaces presenting a contrast of wettability and/or a stepwise texture. Subsequent moulding of the half-cylinder of liquid produces round PDMS microfluidic channels. The optimal parameters for hydrophilic/hydrophobic patterns have then been applied to produce the roundest possible channels. The realisation of both straight channels 300–500 μm wide, 1 cm long and 75° tangent chord angle at best, and Y-shaped channels with the same dimensions and 55° TCA is demonstrated.     

Wear of graphite anodes during electrolysis of add sulphate solutions

Graphite electrodes were prepared by mixing calcined coke and coal tar pitch. They were pressed under 250 kg cm^–2 and heat treated up to 2800° C. Rectangles measuring 70 mm x 40 mm x 8 mm were anodically polarized under galvanostatic and potentiostatic conditions. Electrolyses were conducted at 10–50 mA cm^–2 for periods ranging from 10–120 hours in Na₂SO₄ solutions acidified with sulphuric acid to various pH values. The wear of graphite anodes increased with decreasing bath temperature, increasing acid concentration, decreasing pH of the electrolyte and increasing current density. A model is suggested which assumes that corrosion takes place via the formation of a lamellar crystal compound with the formula (C ₈ ⁰ O)(OH)₃HSO ₄ ^– ·2H₂SO₄.The compound is unstable at higher temperatures when corrosion is effected by oxidation of graphite by atomic oxygen. The formation of the carbon ions was found to be a necessary precondition for the formation of the complex.     

Diffusion of two associated solvents in various compositions through a swelling polymer material,EVAc

The particular sorption by a swelling polymer with the transfer of hydrocarbons was studied in order to evaluate some barrier properties of this material. The transfer of two types of solvents through two varieties of ethylene vinyl acetate was investigated: absorption of pure toluene and pure n‐hexane and absorption of a toluene/hexane mixture in various compositions. A comparison between the two processes showed that these transfers were very different and depended on two factors: vinyl acetate content and composition of the mixture. The kinetics of absorption were calculated for various compositions. The profiles of concentration as well as the kinetics of swelling were evaluated using a numerical model deduced from the general theory of radial diffusion of a substance with change in dimensions. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 2099–2106, 2007     

An efficient IoT based smart farming system using machine learning algorithms

Multimedia Tools and Applications - This paper suggests an IoT based smart farming system along with an efficient prediction method called WPART based on machine learning techniques to predict crop...     

Inter-comparative study of quantitative methods of industrial clinker

Impurities from the raw materials, the grinding and the homogenization of the raw materials, the kiln instability and the complexity of the cooling step, all these factors make it difficult to obtain a perfect evaluation of the mineralogical composition of Portland clinker. We studied the limitations of the most commonly used quantitative methods and recommend some procedures to obtain reliable and reproducible results of quantitative analyses. Different clinker samples (provided by the Bizerte Cement Company (Tunisia)) were subjected to an elemental analysis by X-ray fluorescence and the mineralogical composition was determined by the Bogue calculation and by X-ray powder diffraction combined with the Rietveld method (Different softwares were used: XPert High Score Plus version 2.0 and TOPAS version 4.2). We then compared the results obtained by the Rietveld method and the Bogue calculation to the specific peak areas of each phase. The content of each phase, determined by the Rietveld method, varied proportionally to the change in peak area; a significant difference in these results was found by using the elementary Bogue calculation.     

Power and Wheel Wear for Grinding Nickel Alloy with Plated CBN Wheels

Electroplated CBN grinding wheels are manufactured with a single layer of abrasive grains. The grinding performance of these plated wheels changes significantly as the wheel wears down. The present investigation was undertaken to understand the transient grinding behavior with electroplated CBN wheels in order to provide a logical basis for process control. In this paper, particular attention is directed to the effect of wheel wear and operating parameters on grinding of a nickel alloy. Wheels were worn to various stages and then used to perform grinding tests under various grinding conditions to measure grinding forces and power and to produce ground specimens. Based on models for grinding with conventional aluminum oxide wheels, a power model for grinding of a nickel alloy with plated CBN wheels was established and validated. Microscopic observations of the ground specimens reveal that thermal damage in the form of a White Etch Layer (WEL) appears only when grinding with a worn wheel under conditions that lead to high temperatures.