Air bearing design, optimization, stability analysis andverification for sub-25 nm flying

Three sub-25 nm fly height sliders are presented for near contact recording. The designs are geared towards the goal of achieving 10 Gb/in ² areal density. The optimization procedure presented shows promise for facilitating achievement of this goal. The dynamic simulations show the stability of these designs when disturbed from their steady state conditions     

Further characterisation of protease inhibitors from pigeon pea (cajanus cajan (l) millsp) seeds

Cajanus trypsin inhibitor (CTI) and Cajanus trypsin-chymotrypsin inhibitor (CTCI) previously purified from cv TAT-10 were further characterised. The modification of the inhibitors revealed the presence of lysine at the trypsin reactive site in both CTI and CTCI. Modification of tyrosine at the reactive site of CTCI did not abolish chymotrypsin inhibition suggesting the presence of leucine or phenylalanine as reported in other chymotrypsin inhibitors. CTCI did not contain tryptophan. Dissociation constants for the inhibitors with bovine trypsin were in the region of 0.69 nmol (CTCI) and 0.029 nmol (CTI). Although the protease inhibitors lost their inhibitory activity on exposure to 2-mercaptoethanol they remained attached to the enzyme. The inhibitors were not very effective against the protease from Helicoverpa armigera which is a serious field pest of Cajanus. Dissociation constants for the inhibitors with the larval enzyme were in the region of 100 nmol.     

Non-parametric maximum-likelihood channel estimator and detector for OFDM in presence of interference

A maximum-likelihood channel estimator for the orthogonal frequency division multiplexing communication environments, in the presence of interference is discussed here. In a training-based scenario, the channel is estimated based on pilots that precede the transmission of the information. To reduce the number of estimation parameters, the channel is estimated iteratively in time-domain. Since interference from other users provide no useful information, parameters of the interference are neither estimated nor the effect of the interference neglected, instead interference along with Gaussian noise is perceived as non-Gaussian noise process. The algorithm assumes no a priori knowledge about the interfering channel and signal at the receiver, further no assumption on the statistical properties of the interferer is assumed, which makes this algorithm robust. The estimated channel information along with the estimated distribution are then utilised to equalise the subsequent data blocks. The strength of the algorithm is in its robustness to both synchronous and asynchronous interference, which is confirmed by the simulation results for both flat and multipath fading channels in presence of synchronous and asynchronous interference.     

Characterization of optoacoustic surgical devices

Describes a measurement technique specially developed to characterize optoacoustic sources. The technique provides a convenient baseline for a comparison of different surgical ultrasonic systems utilizing optoacoustic and ultrasonic transducers. In addition, it provides a well-defined tool to optimize the performance of a variety of designs. Attention is focused on the laser-assisted devices in which appropriately delivered light energy is converted into acoustic shock wave. A meaningful comparison of such devices with other therapeutic equipment designed for a direct interaction with tissue requires knowledge of energy needed for a successful surgical treatment. It is demonstrated that knowledge of the key shock wave parameters allows the total acoustic energy associated with the shock wave to be determined. The procedure developed to calculate this energy is discussed and it is shown that the value of this energy can be conveniently used as an indicator of efficacy of an optoacoustic converter in a clinical environment. The influence of the performance of the polyvinylidene fluoride (PVDF) hydrophone probes on the measurement results was also analyzed. It was determined that when appropriately selected, the wide-band PVDF probes are well suited for characterization of the optoacoustic devices in the frequency range 1-100 MHz. The characterization procedure developed is applicable to surgical ultrasonic systems including conventional and laser-assisted phacoemulsifiers     

A fully integrated low-IF CMOS GPS radio with on-chip analog image rejection

A fully integrated Global Positioning System (GPS) radio is presented. Low-IF architecture was used for a high level of integration and low power consumption. An on-chip analog image-reject filter provides 18 dB of image-noise rejection to prevent noise figure (NF) degradation. With image rejection performed in the analog radio, a single-path (nonquadrature) output was used. The integrated synthesizer only requires an off-chip phase-locked loop-filter to function. Implemented in a 0.35-/spl mu/m 2P4M CMOS process, the integrated radio has a chip area of 9.5 mm/sup 2/. The radio operates over a wide range of voltage and temperature, from 2.2 to 3.6 V and from -40/spl deg/C to +85/spl deg/C and consumes 27 mW from a 2.2-V supply. The receiver has 4 dB NF.     

Thermal conductivities of powder-filled epoxy resins

Effective thermal conductivities of powder-filled epoxy composites were experimentally obtained using a transient method. Fillers used were aluminum and cupric oxide. Comparisons of these data with published correlations indicate that Agari's model can give better fits. Nielsen's model may also give a good prediction of the shape of particles can be determined and values of parameters A and ?m are available. An alternative method of dealing with parameter C₂ in Agari's model is suggested. © 1993 John Wiley & Sons, Inc.     

Performance of an activated carbon made from waste palm shell in simultaneous adsorption of SO<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript> and NO<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript> of flue gas at low temperature

This study examined the individual and simultaneous adsorption of SO{in{itx}} (SO{in{it2}}) and NO{in{itx}} (NO-NO{in{it2}}) on activated carbon prepared from waste palm shell. The adsorption process was examined in a fixed bed reactor at low temperatures (100\2-300\dgC). For individual adsorption without any catalytic activation, SO{in{itx}} showed good adsorption whereas NO{in{itx}} was very much poor. In the simultaneous adsorption of SO{in{itx}} and NO{in{itx}}, SO{in{itx}} showed greater adsorption affinity than NO{itx}. For palm shell activated carbon (PSAC) impregnated with metal catalyst (Ni and Ce) the concentration adsorbed profile showed that the amount of SO{in{itx}} adsorbed decreased regularly, while the amount of the adsorbed NO{in{itx}} increased irregularly. The properties of the pure and impregnated PSAC were analyzed by BET, SEM and EDX. These investigations indicated that PSAC impregnated with metal catalyst is the determining factor in the adsorption of SO{in{itx}} and NO{in{itx}} simultaneously. Supported financially by Yayasan FELDA, Malaysia (Grant No. 6050075)     

On the electrochemical nature of hot-corrosion attack in Ni-Cr alloys

Hot-corrosion attack on gas-turbine components has been a problem of practical importance for over two decades. The nature and the extent of corrosion are influenced by the type of contaminants, the alloy constituents, and temperature. The hot-corrosion process is quite complex. There is controversy regarding the role of alloying elements, and whether the process is chemical or electrochemical in nature. In this investigation, an attempt has been made to investigate the role of Al and Ti in influencing the hot-corrosion attack of Ni-20 wt. % Cr alloys in molten Na₂SO₄-NaCl mixtures. It was found that Ni-Cr-Al alloys undergo a localized, heavy-blister attack under certain experimental conditions which is electrochemical in nature. An electrochemical model has been proposed which can satisfatorily explain the nature and kinetics of the localized blister corrosion.     

A wavelet-based method for multiscale tomographic reconstruction

The authors represent the standard ramp filter operator of the filtered-back-projection (FBP) reconstruction in different bases composed of Haar and Daubechies compactly supported wavelets. The resulting multiscale representation of the ramp-filter matrix operator is approximately diagonal. The accuracy of this diagonal approximation becomes better as wavelets with larger numbers of vanishing moments are used. This wavelet-based representation enables the authors to formulate a multiscale tomographic reconstruction technique in which the object is reconstructed at multiple scales or resolutions. A complete reconstruction is obtained by combining the reconstructions at different scales. The authors' multiscale reconstruction technique has the same computational complexity as the FBP reconstruction method. It differs from other multiscale reconstruction techniques in that (1) the object is defined through a one-dimensional multiscale transformation of the projection domain, and (2) the authors explicitly account for noise in the projection data by calculating maximum a posteriori probability (MAP) multiscale reconstruction estimates based on a chosen fractal prior on the multiscale object coefficients. The computational complexity of this maximum a posteriori probability (MAP) solution is also the same as that of the FBP reconstruction. This result is in contrast to commonly used methods of statistical regularization, which result in computationally intensive optimization algorithms.     

Development of a framework for truss-braced wing conceptual MDO

The paper describes the development of a multidisciplinary design optimization framework for conceptual design of truss-braced wing configurations. This unconventional configuration requires specialized analysis tools supported by a modular and flexible framework to accommodate different configurations. While the previous framework developed at Virginia Tech was a monolithic Fortran-77 code, the need for more flexibility for complex truss-braced wing configurations was addressed by the development of this new framework, which is based on Phoenix Integration ModelCenter^TM environment. The framework uses updated structural and aerodynamic design modules that enable a more general geometry definition. The new framework, thus, provides a foundation for future design concepts, especially multi-member truss-braced wing configurations. The fuel saving potential of these truss-braced wing configurations is presented by comparing different truss designs with gradually increased level of complexity.