Blind deconvolution for Doppler centroid estimation in highfrequency SAR

For high-quality SAR (synthetic aperture radar) processing, the Doppler centroid frequency is needed. However, SAR data are sampled along the azimuth direction at the pulse repetition frequency (PRF); the estimation of the Doppler centroid frequency by means of spectral analysis techniques may produce ambiguous results due to aliases. The mathematical expression of the residual error that occurs when SAR data are focused with an incorrect alias of the PRF is thus derived. Then, a blind deconvolution technique is used to estimate the actual PRF replica from the focused image. Squinted X-band data, corresponding to those that will be generated by the SIR-C mission, have been generated from the JPL-AirSAR L- and C-band data by means of an inversion of the focusing process. Even if the real data may show differences with respect to the simulated data, the blind deconvolution method appears to be more precise and robust than the other conventional techniques tested     

Saturation intensity and time response of InGaAs-InGaP MQW opticalmodulators

We report modulation saturation and time response measurements on InGaAs-InGaP MQW modulators. The measurements yield a saturation intensity of (3.7±0.1) kW/cm² for a 0-10 V swing and switching times between 10 and 90 ns, depending on the bias voltage and incident light intensity. The observed dependence indicates that field screening due to carrier build-up is the dominant physical mechanism determining both the speed and the saturation intensity. This conclusion is supported by results of theoretical calculations     

High repetition rate collisional soft X-ray lasers based on grazing incidence pumping

We discuss the demonstration of gain-saturated high repetition rate table-top soft X-ray lasers producing microwatt average powers at wavelengths ranging from 13.9 to 33 nm. The results were obtained heating a precreated plasma with a picosecond optical laser pulse impinging at grazing incidence onto a precreated plasma. This pumping geometry increases the energy deposition efficiency of the pump beam into the gain region, making it possible to saturate soft X-ray lasers in this wavelength range with a short pulse pump energy of only 1 J at 800-nm wavelength. Results corresponding to 5-Hz repetition rate operation of gain-saturated 14.7-nm Ni-like Pd and 32.6-nm line Ne-like Ti lasers pumped by a table-top Ti:sapphire laser are reported. We also discuss results obtained using a 1 /spl omega/1054-nm prepulse and 2 /spl omega/527-nm short pulse from a Nd:glass pump laser. This work demonstrates the feasibility of producing compact high average power soft X-ray lasers for applications.     

Transmission electron microscopy study of Ni–Si nanocomposite films

Nickel induced crystallization of amorphous Si (a-Si) films is investigated using transmission electron microscopy. Metal-induced crystallization was achieved on layered films deposited onto thermally oxidized Si(3 1 1) substrates by electron beam evaporation of a-Si (400 nm) over Ni (50 nm). The multi-layer stack was subjected to post-deposition annealing at 200 and 600 °C for 1 h after the deposition. Microstructural studies reveal the formation of nanosized grains separated by dendritic channels of 5 nm width and 400 nm length. Electron diffraction on selected points within these nanostructured regions shows the presence of face centered cubic NiSi₂ and diamond cubic structured Si. Z-contrast scanning transmission electron microscopy images reveal that the crystallization of Si occurs at the interface between the grains of NiSi₂ and a-Si. X-ray absorption fine structure spectroscopy analysis has been carried out to understand the nature of Ni in the Ni–Si nanocomposite film. The results of the present study indicate that the metal induced crystallization is due to the diffusion of Ni into the a-Si matrix, which then reacts to form nickel silicide at temperatures of the order of 600 °C leading to crystallization of a-Si at the silicide–silicon interface.     

Porous graphitic carbon as stationary phase for LC-ICPMS separation of arsenic compounds in water

A new liquid chromatographic separation method was developed for the speciation of the four main arsenic compounds present in water. Arsenite (As(III)), dimethylarsinic acid (DMA), monomethylarsonic acid (MMA) and arsenate (As(V)) were separated on a recently introduced stationary phase: porous graphitic carbon (PGC). The separation was first obtained under formic acid gradient conditions, but an adsorption phenomenon of As(V) on PGC was observed. To overcome this problem, As(V) was backflushed, and an efficient separation of the four solutes was achieved within 10 min. Extremely low detection limits (ranging from 10 to 70 ng x L(-1)) were obtained by coupling LC with an ICPMS. The method was successfully applied to different spiked mineral waters and a naturally arsenic-containing freshwater.     

Polymer biomaterials (polyphosphazenes) in the repair of peripheral nervous system

Biodegradable polymers gives interesting perspectives of use in making artificial conduits for peripheral nerve reconstruction. Poliphosphazenes are materials highly biocompatible and have a controllable reabsorption rate. According to the substitutes that are introduced in the molecule, they can also be used as a framework for drug release. Conduits obtained with poli [bis(etilalanate) phosphazene] were evaluated as guides for nerve regeneration in an experimental animal model. In six Wistar rats, under general anesthesia and with microsurgical technique, the ischiatic nerve was isolated. On the right side a segment of the nerve was removed in order to create a 10 mm gap. The defect was then repaired using the conduit. On the controlateral limb the nerve continuity was restored using as an autograft the segment removed from the right. Control were performed at 30, 90, 180 days and consisted in histological and electron microscopy investigations. They showed the gradual degradation of the conduit without signs of local and general toxicity. The regeneration of the nerve fibers in the lumen of the conduit was not significantly different from the one obtained with the autologous grafts. So poliphosphazene conduits may be considered effective as a guide for nerve regeneration, above all for the possibility of use the polymer as a carrier for neurite-promoting factors.