Corner flow in free liquid films

A lubrication-flow model for a free film in a corner is presented. The model, written in the hyperbolic coordinate system ξ = x ² −y ², η = 2xy, applies to films that are thin in the η-direction. The lubrication approximation yields two coupled evolution equations for the film thickness and the velocity field which, to lowest order, describes plug flow in the hyperbolic coordinates. A free film in a corner evolving under surface tension and gravity is investigated. The rate of thinning of a free film is compared to that of a film evolving over a solid substrate. Viscous shear and normal stresses are both captured in the model and are computed for the entire flow domain. It is shown that normal stress dominates over shear stress in the far field, while shear stress dominates close to the corner. This revised version was published online in October 2005 with corrected page numbers.     

无线局域网--展望未来

符合802．11b标准的无线局域网为市场上无线网络的发展搭建了稳定的平台。WiFi标准可保证不同厂商产品的互操作性，从而确保最终消费者投资的安全。随着与802．11b同在2．4GHz带宽上运行的更新的802．11g网络的推出，无线网络得到进一步发展。它们既能支持更高速率(最大54Mb/秒)，又具有向下兼容的特性。此外，消费者也可以选择在5GHz带宽的速率上运行802．11a     

Flux Jumps and H-T Diagram of Instability for MgB2

We present a study of magneto-thermal instabilities in polycrystalline MgB₂ superconductor, by magnetic hysteresis loop measurements and by investigations of magnetic flux dynamics with a miniature Hall probe. Temperature and magnetic field ranges where the flux jumps may be observed have been determined. On the basis of measurements of the magnetic flux dynamics, an average magnetic diffusivity describing the process of the flux jump is estimated. This parameter is compared with the thermal and magnetic diffusivities calculated on the basis of available data for thermal conductivity, heat capacity and resistivity. It is shown that the estimated value of the field of the first flux jump is influenced significantly by the field dependence of specific heat. In order to explain the observed phenomenon, the temperature reached by the sample during the flux jump at different magnetic fields is calculated.     

A quadruple well, quadruple polysilicon BiCMOS process for fast 16Mb SRAM's

An advanced, high-performance, quadruple well, quadruple polysilicon BiCMOS technology has been developed for fast 16 Mb SRAM's. A split word-line bitcell architecture, using four levels of polysilicon and two self-aligned contacts, achieves a cell area of 8.61 μm² with conventional I-line lithography and 7.32 μm² with I-line plus phase-shift or with deep UV lithography. The process features PELOX isolation to provide a 1.0 μm active pitch, MOSFET transistors designed for a 0.80 μm gate poly pitch, a double polysilicon bipolar transistor with aggressively scaled parasitics, and a thin-film polysilicon transistor to enhance bitcell stability. A quadruple-well structure improves soft error rate (SER) and allows simultaneous optimization of MOSFET and bipolar performance     

Motor oil classification by base stock and viscosity based on near infrared (NIR) spectroscopy data

In this paper we have tried to build effective model for classification of motor oils by base stock and viscosity class. Three (3) sets of near infrared (NIR) spectra (1125, 1010, and 1050 spectra) were used for classification of motor oils into 3 or 4 classes according to their base stock (synthetic, semi-synthetic, and mineral), kinematic viscosity at low temperature (SAE 0W, 5W, 10W, and 15W) and kinematic viscosity at high temperature (SAE 20, 30, 40, and 50). The abilities of three (3) different classification methods: regularized discriminant analysis (RDA), soft independent modelling of class analogy (SIMCA), and multilayer perceptron (MLP) - were also compared. In all cases NIR spectroscopy was found to be quite effective for motor oil classification. MLP classification technique was found to be the most effective one.     

Inverse Analysis of Axisymmetrical Compression of HSLA Steel

The objective of the present work is to further explore the problem of selection of the flow stress function which will give the best agreement with experiments for a wide range of the Zener‐Hollomon parameter. Analysis of various flow stress functions was performed, with particular emphasis on the Zerilli‐Armstrong model. Inverse analysis was successfully applied to identify the flow stress model for microalloyed steels deformed in ferrite, two‐phase and austenite regions. Inverse method is applied to interpret the results of the axisymmetrical compression tests performed for HSLA steel samples on a Gleeble 3800 and Split Hopkinson Pressure Bar. Sensitivity analysis is performed based on local and global methods. The objective of the sensitivity analysis in the present study is the evaluation to what extent the selected coefficients in the rheological model influence the result of simulations. In the considered tests this result is represented by two dependent variables, the load and the shape of the sample (barrelling). It is confirmed that the Zerilli‐Armstrong equations should be applied at very high strain rates. Physical meaning is an advantage of this model. Difficulties with identification are the main disadvantage.     

Scale Transition in Steel-Concrete Interaction. II:?Applications

The proposed mode of consideration of the steel-concrete interaction (Part I) is applied to real-life engineering structures. Two structures recently investigated numerically at Vienna University of Technology are considered: (1) the reinforced concrete (RC) cooling tower III Ptolema?s SES (Greece) and (2) a part of the shotcrete tunnel lining installed at the Lainzer tunnel (Austria). In both examples, the uniaxial fracture criterion used in Part I is replaced by the maximum stress (Rankine) criterion. Together with the Drucker-Prager criterion, which is used for the simulation of compressive failure of concrete/shotcrete, it defines the space of admissible stress states in the framework of multisurface plasticity. For the simulation of early-age fracture of shotcrete, consideration of the steel-concrete interaction presented in Part I of this paper is extended towards young shotcrete. Similar to the benchmark problem investigated in Part I of this paper, several analyses with different degrees of consideration of the steel-concrete interaction are performed. The obtained results give insight into the influence of the steel-concrete interaction on the load-carrying behavior of the investigated structures.