On the performance of improved quadrature spatial modulation

Quadrature spatial modulation (QSM) utilizes the in‐phase and quadrature spatial dimensions to transmit the real and imaginary parts of a single signal symbol, respectively. The improved QSM (IQSM) transmits two signal symbols per channel use through a combination of two antennas for each of the real and imaginary parts. The main contributions of this study can be summarized as follows. First, we derive an upper bound for the error performance of the IQSM. We then design constellation sets that minimize the error performance of the IQSM for several system configurations. Second, we propose a double QSM (DQSM) that transmits the real and imaginary parts of two signal symbols through any available transmit antennas. Finally, we propose a parallel IQSM (PIQSM) that splits the antenna set into equal subsets and performs IQSM within each subset using the same two signal symbols. Simulation results demonstrate that the proposed constellations significantly outperform conventional constellations. Additionally, DQSM and PIQSM provide a performance similar to that of IQSM while requiring a smaller number of transmit antennas and outperform IQSM with the same number of transmit antennas.     

Morphology development in polyethylene/polystyrene blends: the influence of processing conditions and interfacial modification

The influence of processing conditions and interfacial modification on the morphology evolution and the composition range within which fully co‐continuous high density polyethylene/polystyrene blend structures can exist during blending in a single screw extruder was studied. Blends ranging from pure A to pure B component, with and without compatibilizer, were prepared under two different shear rates. It was found that high shear rates displaced the breakdown–coalescence balance of the dispersed nodules to the side of coalescence, narrowing the percolation domain and the critical composition for full co‐continuity decreased with increasing shear rates. The addition of a tri‐block compatibilizer induced the percolation threshold of the polystyrene phase to begin at lower percentages of polyethylene but the phase inversion point did not change. The experimental results are discussed in the light of various theoretical models. Copyright © 2005 Society of Chemical Industry     

Non-Intrusive Monitoring of Everyday Behavioral Activities in an Indoor Environment

A non-intrusive design for monitoring everyday activities of an elderly person is presented. The proposed system is intended to be used in the bedroom, allowing the elders to stay at home in a safe environment. The required hardware design is simple in structure and cost effective. The sensor design is implemented by using capacitive sensors and an Arduino microcontroller unit. And a real time graphical user interface is implemented to monitor the elderly person. The performance analysis shows that the sensor design is able to differentiate between a human body and a house pet.     

Activation Energy of Aggregation-Disaggregation Self-Oscillation of Polymer Chain

In this paper, we investigated the activation energies of the aggregation–disaggregation self-oscillation induced by the Belousov-Zhabotinsky (BZ) reaction by utilizing the nonthermoresponsive polymer chain in a wide temperature range. This is because the conventional type self-oscillating polymer chain, with thermoresponsive poly(Nisopropylacrylamide) (poly(NIPAAm) main-chain covalently bonded to the ruthenium catalyst (Ru(bpy)₃) of the BZ reaction, cannot evaluate the activation energy over the lower critical solution temperature (LCST). The nonthermoresponsive self-oscillating polymer chain is composed of a poly-vinylpyrrolidone (PVP) main-chain with the ruthenium catalyst (Ru(bpy)₃). As a result, we clarified that the activation energy of the aggregation–disaggregation self-oscillation of the polymer chain is hardly affected by the concentrations of the BZ substrates. In addition, the activation energy of the nonthermoresponsive self-oscillating polymer chain was found to be almost the same value as normal BZ reaction, i.e., not including the self-oscillating polymer system with Ru moiety.     

Distinct Pharmacological Properties of Gaseous CO and CO-Releasing Molecule in Human Platelets

Carbon monoxide (CO)—gaseous or released by CO-RMs—both possess antiplatelet properties; however, it remains uncertain whether the mechanisms involved are the same. Here, we characterise the involvement of soluble guanylate cyclase (sGC) in the effects of CO—delivered by gaseous CO–saturated buffer (CO_G) and generated by CORM-A1—on platelet aggregation and energy metabolism, as well as on vasodilatation in aorta, using light transmission aggregometry, Seahorse XFe technique, and wire myography, respectively. ODQ completely prevented the inhibitory effect of CO_G on platelet aggregation, but did not modify antiplatelet effect of CORM-A1. In turn, CO_G did not affect, whereas CORM-A1 substantially inhibited energy metabolism in platelets. Even though activation of sGC by BAY 41-2272 or BAY 58-2667 inhibited significantly platelet aggregation, their effects on energy metabolism in platelets were absent or weak and could not contribute to antiplatelet effects of sGC activation. In contrast, vasodilatation of murine aortic rings, induced either by CO_G or CORM-A1, was dependent on sGC. We conclude that the source (CO_G vs. CORM-A1) and kinetics (rapid vs. slow) of CO delivery represent key determinants of the mechanism of antiplatelet action of CO, involving either impairment of energy metabolism or activation of sGG.     

Ergonomic mismatch between students anthropometry and university classroom furniture

University students spend most of their time in classrooms, mostly in a sitting position. Prolonged sitting on ill-fitted furniture and the resulting bad posture is making students suffer from different musculoskeletal disorders (MSDs). This study evaluates the potential mismatch between furniture dimensions and anthropometric measurements. To determine potential mismatch, 13 anthropometric measurements of 550 students and 11 dimensions of two types of classroom furniture (mounted-desktop and chair-with-table) were measured and then compared. Additionally, chi-square test was performed to compare the relation between anthropometry and relevant furniture dimensions. Results showed that a significant number of mismatches emerged between anthropometric measurements and furniture dimensions. For both types of furniture, seat height was too high and seat depth was too deep. Moreover, for mounted desktop, desk height is almost appropriate for all students whereas for chair and table, it was too high for the males. These circumstances may lead to increase discomfort and increase MSDs problems among all students. It can be concluded that the dimensions of both types of classroom furniture were not appropriate for users according to anthropometric measurements. This analysis recommends the measurements of furniture dimensions based on participants’ anthropometric measurements to avoid or minimise discomfort and MSDs problems.     

Brinkman–Forchheimer modeling for porous media thermoacoustic system

In this paper, analytical studies have been conducted on the flow and thermal fields of unsteady compressible viscous oscillating flow through channels filled with porous media representing stacks in thermoacoustic systems. The flow in the porous material is described by the Brinkman–Forchheimer–extended Darcy model. Analytical expressions for oscillating velocity, temperature, and energy flux density are obtained after linearizing and solving the governing differential equations with long wave, short stack, and small amplitude oscillation approximations. Experimental work is also conducted to verify the temperature difference obtained across the porous stack ends. To produce the experimental results, a thermoacoustic heat pump is designed and constructed where reticulated vitreous carbon (RVC) is used as the stack material. A very good agreement is obtained between the modeling and the experimental results. The expression of temperature difference across the stack ends obtained in the present study is also compared with the existing thermoacoustic literature. The proposed expression surpasses the existing expression available in the literature. The system of equations developed in the present study is a helpful tool for thermal engineers and physicist to design porous stacks for thermoacoustic devices.     

Porous hydroxyapatite coating on strong ceramic substrate fabricated by low density slip coating-deposition and coating-substrate co-sintering

This study aims at developing a process technique, which can deposit porous scaffold-like hydroxyapatite (HA) coatings on strong ceramic substrates. As a first trial, micro-porous HA coatings on strong zirconia-based substrates are fabricated by the following technique—consisting of low-density HA-slip coating-deposition on the micro-porous substrates pre-sintered at 900 °C, and coating-substrate co-sintering at 1300 °C. The final co-sintering process ensures a strong bonding between the HA coating and the zirconia-based substrate after minimizing the mismatch in thermal expansion coefficients by adding alumina in HA coating and HA in zirconia-based substrate. The presence of porosity in the HA coating also reduces the mismatch. HA decomposition during the co-sintering process is discussed.     

Seismic Behavior of Flexural Dominated Reinforced Concrete Bridge Columns at Low Temperatures

This paper presents the results from Phase II of an experimental study on the behavior of reinforced concrete bridge columns in cold seismicly active regions. Six half-scale circular reinforced concrete columns, designed to be flexural dominated, were tested under reversed cyclic loading while subjected to temperatures ranging from ?36°C (?33°F) to 22°C (72°F). Four of the units tested were reinforced concrete filled steel tube (RCFST) columns and the other two were ordinary reinforced concrete columns. Results obtained reiterated the observations made in Phase I, which is that low temperatures cause an increase in the flexural strength and initial stiffness as well as a reduction in the spread of plasticity and displacement capacity of the column. Another important observation made was that the plastic hinge length is drastically reduced in the RCFST units compromising the displacement capacity of this type of column even at room temperature conditions. Current predictive models were revised and modified to account for the low-temperature effect.     

Individual Variabilities in Adipose Stem Cell Proliferation,Gene Expression and Responses to Lipopolysaccharide Stimulation

Adipose stem cells (ASCs) are reported to play a role in normal physiology as well as in inflammation and disease. The objective of this work was to elucidate inter-individual differences in growth, gene expression and response to inflammatory stimuli in ASCs from different donors. Human ASC1 (male donor) and ASC2 (female donor) were purchased from Lonza (Walkersville, MD). Cell proliferation was determined by the sulforhodamine B assay. After time-dependent treatment of ASCs with or without bacterial lipopolysaccharide (LPS), marker gene mRNAs for proliferation, steroid hormones, and xenobiotic and immune pathways were determined using RT-PCR, and secreted cytokine levels in media were measured using the Bio-Plex cytokine assay kit. ASCs from both donors expressed androgen receptors but not estrogen receptors. ASC2 had a 2-fold higher proliferation rate and a 6-fold higher level of proliferation marker Ki67 mRNA than ASC1. ASC2 exhibited significantly greater fold induction of TNF-α and CCL2 by LPS compared to ASC1. TNF-α and GM-CSF protein levels were also significantly higher in the LPS-induced ASC2 media, but IL-6 secretion was higher in the LPS-induced ASC1 media. Our findings suggest that inter-individual variability and/or possible sex differences exist in ASCs, which may serve as a key determinant to inflammatory responses of ASCs.