Nano fibrillated cellulose-based foam by Pickering emulsion: Preparation,characterizations, and application as dye adsorbent

An ecofriendly and biodegradable porous structure was prepared from drying aqueous foams based on nano fibrillated cellulose (NFC), extracted from softwood pulp by subcritical water/CO₂ treatment (SC-NFC). The primary aim of this work was to use the modified SC-NFC as stabilizer for a water-based Pickering emulsion which upon drying, yielded porous cellulosic materials, a good dye adsorbent. In order to exploit the carboxymethylated SC-NFC (CMSC-NFC, with a degree of substitution of 0.35 and a charge density of 649 μeqv/g) as a stabilizer for water-based Pickering emulsion in subsequent step, an optimized quantity of octyl amine (30 mg/g of SC-NFC) was added to make them partially hydrophobic. A series of dry foam structures were prepared by varying the concentrations of treated CMSC-NFCs and 4 wt% was found to be the optimum concentration to yield foam with high porosity (99%) and low density (0.038 g/cc) along with high compression strength (0.24 MPa), superior to the conventionally extracted NFC. The foams were applied to capture as high as 98% of methylene blue dyes, making them a potential green candidate for treating industrial effluent. In addition, the dye adsorption kinetics and isotherms were found to be well suited with second order kinetics and Langmuir isotherm models.     

Effect of spheroidized microstructure on the impact toughness and electrochemical performance of a high-carbon steel

The influence of cementite spheroidization on the impact toughness and electrochemical properties of a high-carbon steel has been thoroughly investigated in this study. Heavy warm rolling, followed by 2 h of annealing, has resulted in near-complete spheroidization, leading to a microstructure consisting of nano-cementite globules dispersed in the ultrafine-grained ferritic matrix. The Charpy impact test exhibited superior impact toughness with increased spheroidization. It is validated by the presence of abundant dimples in the fractographs of spheroidized specimens, in contrast to the as-received one that experienced a brittle failure due to its lamellar pearlitic structure. Potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) carried out in a 3.5% NaCl solution revealed that the corrosion resistance of the alloy gets improved with the increase in the degree of spheroidization. This is attributed to the lower susceptibility of the spheroidized specimen to microgalvanic corrosion owing to the minimum area of contact between nano-spheroidized cementite and ferrite, as elucidated with the help of EIS results aided by equivalent electrical circuit model.     

Impact of Climate Change on Future Flood Susceptibility: an Evaluation Based on Deep Learning Algorithms and GCM Model

Floods are common and recurring natural hazards which damages is the destruction for society. Several regions of the world with different climatic conditions face the challenge of floods in different magnitudes. Here we estimate flood susceptibility based on Analytical neural network (ANN), Deep learning neural network (DLNN) and Deep boost (DB) algorithm approach. We also attempt to estimate the future rainfall scenario, using the General circulation model (GCM) with its ensemble. The Representative concentration pathway (RCP) scenario is employed for estimating the future rainfall in more an authentic way. The validation of all models was done with considering different indices and the results show that the DB model is most optimal as compared to the other models. According to the DB model, the spatial coverage of very low, low, moderate, high and very high flood prone region is 68.20%, 9.48%, 5.64%, 7.34% and 9.33% respectively. The approach and results in this research would be beneficial to take the decision in managing this natural hazard in a more efficient way.

     

Impact of Mole Fractions due to Work Function Variability (WFV) of Metal Gate on Electrical Parameters in Strained SOI-FinFET

In the recent sub-20 nm technology node, the process variability issues have become a major problem for scaling of MOS devices. We present a design for a strained Si/SiGe FinFET on an insulator using a 3D TCAD simulator. The impact of metal gate work function variability (WFV) on electrical parameters is studied. Such impact of WFV for different mole fractions (x) of the SiGe layer in a strained SOI-FinFET with varying grain size is presented. The results show that as the mole fraction is increased, the variability in threshold voltage (σVT) and off current (σIoff) is decreased; while, the variability of on-current (σIon) is increased. A notable observation is the distribution of electrical parameters approaches a normal distribution for smaller grain sizes.     

Sustainable biocarbon as an alternative of traditional fillers for poly(butylene terephthalate)-based composites: Thermo-oxidative aging and durability

Sustainable biocomposites have gained considerable interest as an alternative to conventional composites in recent years due to their cost-effectiveness and environmental friendliness. The aim of this study was to investigate the performance and durability behavior of biocomposites from sustainable biocarbon (BC) as compared to conventional established fillers. The poly(butylene terephthalate) (PBT) and its composites reinforced with BC, talc, and glass fiber (GF) were prepared and the durability performances was investigated. The study showed that BC/PBT biocomposites provided a lighter weight alternative to traditionally used fillers. After undergoes thermo-oxidative aging, the mechanical properties of BC/PBT biocomposite were deteriorated. The GF/PBT showed the most stable in retaining its mechanical properties in comparison to the talc/PBT and BC/PBT. The aging behavior and mechanism of the PBT composites were discussed. This study provides further insight on the durability-related properties progression of biocomposites as compared to traditional used fillers. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47722.     

Intercarrier bandwidth exchange: an engineering framework

A mismatch between demand and supply for bandwidth is common in transport carrier networks. This mismatch is generally a result of the disparity between a carrier's capacity buildout and its anticipated customer demand. A carrier with temporary bandwidth deficit or lack of presence in a geographical region and a carrier with surplus capacity in the right locations can be brought together by the emerging bandwidth exchange technology. Bandwidth exchange offers a win-win solution, in which the carrier with a deficit avoids losing revenue by buying capacity from the carrier with surplus, and the latter makes additional revenue by retail sale of its excess capacity. While the concept of real-time purchase and exchange of bandwidth has attracted a lot of attention, many technical challenges stand in the way of making it a reality. The purpose of this article is to provide an engineering framework for enabling real-time bandwidth exchange with committed quality of service and service level agreement among transport carriers. Special emphasis is given to identifying the architectural requirements and the enabling infrastructure necessary for building a viable bandwidth exchange that can be used for creating revenue out of surplus stranded capacity. Indepth analysis of cross-carrier service level agreement specification, capacity publication, route design, and service provisioning are also provided in the article.     

Mixed waste ferrite as a novel sorbent for carbon dioxide derived from flue gases

Ferrite is a potential sorbent for flue gases such as CO₂, H₂S and SO₂. This paper discusses the adsorption and decomposition of CO₂ into carbon by hydrogen-activated waste ferrites prepared from Berkeley Pit acid mine water (Butte, MT). The decomposition effectiveness of these waste ferrites was studied at 300 °C and compared with the synthetic magnetite obtained from ferrous sulfate solution in our laboratory. The decomposition was measured by two methods: indirectly by measuring the adsorption rate of CO₂ and directly by analysing the carbon deposited on the samples. The results indicated that the mixed waste ferrite had good affinity for the adsorption and decomposition. The CO₂ decomposition data of both sorbents fitted the first-order reaction kinetics. Even though the surface area of the magnetite was higher than that of waste ferrite, the CO₂ decomposition rate of the waste ferrite was estimated to be 2.5 times higher than that of magnetite under identical conditions. The carbon analysis deposited on the sample indicated that the CO₂ was 100% decomposed into carbon and other carbon/hydrogen compounds by the waste ferrite, whereas the conversion was 43% by the magnetite. In terms of specific adsorption of carbon, ferrite was three to five times more efficient than magnetite.