Isothermal interphase diffusion with consecutive reactions

For multi-step heterogeneous consecutive reactions affected entirely by interphase diffusion under isothermal condition, the equations for the effectiveness factors, the surface concentrations and the point yields were derived in terms of the Damkoehler numbers or the measurables from the mass balances set up on the assumption that the mass-transfer rate balances the surface-reaction rate at steady state. From the analyses of the equations derived, the effectiveness factors for the intermediate steps and the surface concentrations of intermediates were understood to be enhanced by the measurables inclusive of the concentrations and the mass-transfer coefficients. Then the effect of the concentrations was concluded to be most significant. The effects of these measurables to the effectiveness factors and the surface concentrations were qualitatively discussed for simple consecutive reactions and also for additive consecutive reactions. Especially, as for two-step additive consecutive reactions, the effects of measurables η Da and the concentrations to the effectiveness factors were examined with graphical presentations. Finally, the brief discussion of the dependency of the Damkoehler number upon reaction time and the effect of the Renolds number and diffusivity to the extent of the mass-transfer resistance were presented.     

Preparation of spinel-type ferrite thin films by the dip-coating process and their magnetic properties

Films of spinel-type ferrite, MFe₂O₄ (M=Ni, Co, Mg, Li_0.5Fe_0.5) have been prepared by a dip-coating method from the sol-gel process. Ferric nitrate, nickel nitrate, cobalt nitrate and lithium nitrate were used as raw materials, and glycerol and formamide were used as solvents. A film was prepared by dipping a silica glass plate. The spinel-type ferrite was obtained by heat-treatment at 700–900°C for 2 h in air. The film thickness was about 0.8 m. The saturation magnetization, _r, of the film and powder with composition 50NiO·50Fe₂O₃ was 196 emu cm^–3 and 29.1 emu g^–1, respectively, and the coercive force,H _c, was 140 and 95 Oe, respectively, after heat-treatment at 800°C for 2 h. In particular, the films were shown to have a much largerH _c than the powder. The grain growth of spinel ferrite may be subject to restriction because it is in progress above an amorphous base-plate. The crystals are therefore aligned with the base-plate and have uniaxial anisotropy.     

N，O，O′─三（对甲苯磺酰基）双（2─羟乙基）胺的合成

二乙醇胺和对甲苯磺酰氯在三乙胺存在下，反应生成Ｎ，０，Ｏ′－三（对甲苯磺酰基）双（２－羟乙基）胺，产率９３％。从反应混合物中分离得副产物Ｎ，Ｏ－二（对甲苯磺酰基）双（２－羟乙基）胺。     

Inertial effects on cylindrical particle migration in linear shear flow near a wall

Micro-/nanoparticle-based systems are regarded as one of the possible candidates due to the engineerability and multifunctionality to maximize the accumulation of the nano-/microparticle-based drug delivery system on the target. Recent advances in nanotechnology enable the fabrication of diverse particle shapes from simple spherical particles to more complex shapes. The particle dynamics in blood flow and endocytosis characteristics of non-spherical particles change as the non-sphericity effect increases. We used a numerical approach to investigate the particle dynamics in linear shear flow near a wall. We examined the dynamics of slender cylindrical particles with aspect ratio γ = 5.0 in terms of particle trajectory, velocity, and force variation for different Stokes numbers over time. We identified the rotating inertia of particle near a wall as the source of inertial migration toward the wall. The drift velocity of slender cylindrical particles is comparable to that of discoidal particles. We discuss the possibilities and limitations of using slender cylindrical particles as a drug delivery system.     

Microalgae-Based Biohybrid Microrobot for Accelerated Diabetic Wound Healing

A variety of wound healing platforms have been proposed to alleviate the hypoxic condition and/or to modulate the immune responses for the treatment of chronic wounds in diabetes. However, these platforms with the passive diffusion of therapeutic agents through the blood clot result in the relatively low delivery efficiency into the deep wound site. Here, a microalgae-based biohybrid microrobot for accelerated diabetic wound healing is developed. The biohybrid microrobot autonomously moves at velocity of 33.3 µm s⁻¹ and generates oxygen for the alleviation of hypoxic condition. In addition, the microrobot efficiently bound with inflammatory chemokines of interleukin-8 (IL-8) and monocyte chemoattractant protein-1 (MCP-1) for modulating the immune responses. The enhanced penetration of microrobot is corroborated by measuring fibrin clots in biomimetic wound using microfluidic devices and the enhanced retention of microrobot is confirmed in the real wounded mouse skin tissue. After deposition on the chronic wound in diabetic mice without wound dressing, the wounds treated with microrobots are completely healed after 9 days with the significant decrease of inflammatory cytokines below 31% of the control level and the upregulated angiogenesis above 20 times of CD31⁺ cells. These results confirm the feasibility of microrobots as a next-generation platform for diabetic wound healing.     

Physico-chemical properties of glycyrrhizic acid in aqueous media. I. Surface-active properties and formation of molecular aggregates (author''s transl)

As shown in 138 embryos and fetuses in the 40-285 mm crown-rump length range, carpal and carpal-metacarpal "fusions" arise from incomplete separation of the cartilaginous precursors rather than from failure of initiation, thus accounting for the "fusions" seen in postnatal radiographs and the grooves that are evident enough in adult fusions. Radiographs selected from over 20,000 apparently normal individuals provide postnatal counterparts for the prenatal examples shown in histological sections.     

A semi‐adaptive control approach to closed‐loop medication infusion

This paper presents a semi‐adaptive control approach to closed‐loop medication infusion problems. The rationale underlying this approach is to design a controller that can adapt model parameters with a large impact on the model's fidelity while fixing the remaining parameters at nominal values. In this paper, a control‐oriented model for this purpose is derived via system identification and sensitivity analysis of a low‐order model capturing the direct dose‐response relationship Using the model thus derived, a model‐reference adaptive controller and a composite adaptive controller are designed and compared with each other. In‐silico simulation results using remifentanil's effect on respiratory rate as an example indicate that both controllers can regulate the output at commanded set points. Copyright © 2016 John Wiley & Sons, Ltd.     

The effect of roll-processing orientation on stress corrosion cracking of warm-rolled 304L stainless steel in oxygenated and deoxygenated high temperature pure water

Stress corrosion crack growth rates of 304L stainless steel after one-directionally warm-rolled along the longitudinal (L) direction were measured in oxygenated and deoxygenated pure water at 288 °C. The fracture mode is mainly intergranular in the Transverse-longitudinal (T-L) orientation specimen, while it is occasionally intergranular in the Longitudinal-transverse (L-T) orientation specimen. The crack growth rates in the T-L orientation are higher than those in the L-T orientation in both oxygenated and deoxygenated environments, which is related to the effective cracking growth path as the result of microstructural anisotropy and applied loading direction.