Development of a suitable model for characterizing photovoltaic arrays with shaded solar cells

The aim of this study is to investigate the effects of non-uniform solar irradiation distribution on energy output of different interconnected configurations in photovoltaic (PV) arrays. In order to find which configuration is less susceptible to mismatch effects, a PV module model is developed. This model can take into consideration the effects of bypass diodes and the variation of the equivalent circuit parameters with respect to operating conditions. The proposed model can provide sufficient degree of precision as well as solar cell-based analysis in analyzing large scale PV arrays without increasing the computational effort. In order to produce more reliable and robust simulations, improved and extended algorithms are presented. Some results are discussed in detail and some recommendations are extracted by testing several shading scenarios.     

Surface modification of polyester and polyamide fabrics by low frequency plasma polymerization of acrylic acid

In this study, the surface characteristics of polyester and polyamide fabrics were changed by plasma polymerization technique utilizing acrylic acid as precursor. This monomer was used to produce hydrophilic materials with extended absorbency. The hydrophilicity, total wrinkle recovery angle (WRA°) and breaking strength of the fabrics were determined prior and after plasma polymerization treatment. The modification of surfaces was carried out at low pressure (<100 Pa) and low temperature (<50°C) plasma conditions. The effects of exposure time and discharge power parameters were optimized by comparing properties of the fabrics before and after plasma polymerization treatments. It was shown that two sides of polyester fabric samples were treated equally and homogeneously in plasma reactor. For polyester fabrics, the minimum wetting time, 0.5 s, was observed at two plasma processing parameters of 10 W–45 min and 10 W–20 min, where untreated fabric has a wetting time of 6 s. For polyester fabrics, the maximum value was obtained at 60 W–5 min with the wrinkle recovery angle of 306° where the untreated fabric has 290°. The optimum plasma conditions for polyamide fabrics were determined as 30 W–45 min where 2 s wetting time was observed. Wrinkle recovery angle of untreated polyamide fabric was 264°. In this study, after plasma polymerization of acrylic acid, wrinkle recovery angle values were increased by 13%. No significant change was observed in breaking strength of both fabrics after plasma treatment. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 2318–2322, 2007     

Synthesis and properties of chitosan-modified poly(vinyl butyrate)

Modification of chitosan by grafting of vinyl butyrate was carried out in homogeneous phase using potassium persulfate as redox initator and 1.5% acetic acid as solvent. The percent grafting and grafting efficiency were analysed and the high grafting efficiency up to 94% was observed. The effects of reaction variables such as monomer concentration, initiator concentration, temperature and reaction time were investigated. It was observed that the solubility of chitosan was markedly reduced after grafting with vinyl butyrate. The grafted product is insoluble in common organic solvents as well in dilute organic and inorganic acids. Characterization of the graft copolymers were carried out by using Fourier Transform Infrared Spectroscopy (FTIR), Differential Scanning Calorimetry (DSC) and Scanning Electron Microscopy (SEM) technics. Characteristic signal of carbonyl group was observed at 1,731 cm⁻¹ which belongs to the poly vinyl butyrate segments in the graft copolymer. The melting transition of the chitosan main chain in the copolymer shifted to 124°C from its original value 101°C. In addition to these, we have also studied topology of the graft copolymer and the SEM micrograph showed continuous homogenous matrix which means there is no phase separation.     

Is cheating a human function? The roles of presence,state hostility,and enjoyment in an unfair video game

In sports and board games, when an opponent cheats, the other players typically greet it with disdain, anger, and disengagement. However, work has yet to fully address the role of the computer cheating in video games. In this study, participants played either a cheating or a non-cheating version of a modified open-source tower-defense game. Results indicate that when a computer competitor cheats, players perceive the opponent as being more human. Cheating also increases player aggravation and presence, but does not affect enjoyment of the experience. Additionally, players that firmly believed that their opponent was controlled by the computer exhibited significantly less state hostility compared to players that were less certain of the nature of their competitor. Game designers can integrate subtle levels of cheating into computer opponents without any real negative responses from the players. The results indicate that minor levels of cheating might also increase player engagement with video games.     

Slip initiation on frictional fractures

Direct shear tests and biaxial compression tests are conducted to investigate the onset of slip along a non-homogeneous frictional surface and to determine the effect of specimen thickness and confining stress on slip initiation and propagation. The specimens are made of two and three acrylic blocks with the contact surfaces between blocks having on their upper half a frictional strength smaller than on their lower half. This creates a “weak” surface on the upper half and a “strong” surface on the lower half. The specimens are then loaded in direct shear or biaxial compression with confining pressures ranging from 0.7 to 3.5 MPa. The onset of slip, slip propagation, and the stress field generated at the front and center of the blocks interfaces are monitored using a photoelastic technique where a thin photoelastic film is placed at the location where observations are made. The onset of slip at the weak-strong zone interface is treated as propagation of a frictional crack under Mode II loading. The critical stress intensity factor, K_IIC, at the onset of slip is obtained from photoelastic techniques. The results show a weak dependency of K_IIC on the normal stress applied and no influence of the specimen size for specimens thicker than 25.4 mm; for thinner specimens the K_IIC values are smaller because the boundaries of the specimen prevent the full development of the stress field ahead of the crack tip. The experiments show a linear increase of the critical energy release rate with normal stress which is explained with linear elastic fracture mechanics theories.     

PET纤维纺丝中采用纳米微粒添加剂的相关问题

在许多市场和用途中采用尺寸更小的微粒材料的趋势正明显增长。在纤维纺丝中加入整个范围的添加剂（包含纳米微粒）开发具有特殊性能纺织品时存在着一些争论。纤维纺丝中的主要问题是开发低含量的添加剂。     

The use of basalt powder as a natural heterogeneous catalyst in the Fenton and Photo-Fenton oxidation of cationic dyes

The use of naturally present heterogeneous catalysts has recently been an essential issue in the Fenton and photo-Fenton processes. In this study, the uses of basalt as a catalyst for the Fenton and photo-Fenton reactions for methylene Blue (MB) and Basic Red 18 (BR18) degradations were investigated. Basalt was selected because of the presence of the iron (III) oxide in the structure. Basalt was characterized by X-Ray Fluorescence (XRF) and X-Ray Diffraction (XRD) analysis to obtain the chemical composition and the crystalline phase. The surface charge and the surface area were obtained by zeta potential and Brunauer Emmett-Teller (BET) analysis. Fourier Transform Infrared Spectroscopy (FTIR) and scanning electron microscope (SEM) were utilized to explore the functional group and the surface morphology. Fenton and photo-Fenton processes were applied to explore the best degradation method. Adsorption was also tested and the adsorption process had minimum removal efficiency (12% for MB and 17% for BR18). The removal efficiencies for MB and BR18 by the Fenton process were 87% and 28%, respectively. The photo-Fenton process had maximum removal efficiency with 100% for MB and 70% for BR18. The optimum conditions were 70 mg/L dye concentration, 5 mM H₂O₂, 1.0 g/L basalt loading and pH 2. Basalt has shown reuse capability as a catalyst for three consecutive cycles.     

Planning maintenance works on pavements through ant colony optimization

Pavements constructed for the purpose of meeting the demand of highways which were emerged with the improving technological developments increased. And consequently, more resources were demanded to be directed to pavement maintenance and rehabilitation. Hereby, the concept of pavement management emerged. Although project-level analyses were found adequate previously, network-level evaluations were needed in order to do detailed planning as a result of resource allocation and transfer problems that were emerged later. Therefore, pavement management system has become compulsory for all pavements to be controlled together. In this framework, programming is needed in order to schedule maintenance–rehabilitation and develop costs with respect to budget. In the study carried out, a mode was developed in order to program the routine network maintenance activities in terms of Pavement Maintenance and Management Systems, and it was concluded that this problem can be solved through ant colony, using Visual Basic.     

Soft Matter Technology at KIT: Chemical Perspective from Nanoarchitectures to Microstructures

Bioinspiration has emerged as an important design principle in the rapidly growing field of materials science and especially its subarea, soft matter science. For example, biological cells form hierarchically organized tissues that not only are optimized and designed for durability, but also have to adapt to their external environment, undergo self‐repair, and perform many highly complex functions. Being able to create artificial soft materials that mimic those highly complex functions will enable future materials applications. Herein, soft matter technologies that are used to realize bioinspired material structures are described, and potential pathways to integrate these into a comprehensive soft matter research environment are addressed. Solutions become available because soft matter technologies are benefitting from the synergies between organic synthesis, polymer chemistry, and materials science.     

Long-term microleakage trends in access cavities conditioned with phosphoric acid and deproteinizing agent for root-canal-treated teeth: an investigation of fluid filtration and microscopy analysis

This study evaluated the long-term microleakage of access cavities conditioned with phosphoric acid and deproteinizing agents for root-canal-treated teeth using fluid filtration and microscopical analysis. Occlusal surfaces of extracted human mandibular premolars (N = 90) were removed leaving a 4 mm coronal length from the cemento-enamel junction. After root canal treatment, the specimens were randomly divided into four experimental groups (n = 21) and the remaining teeth were used for positive control group (n = 6): SB: 35% H₃PO₄ + Adper Single Bond 2; SSB: 35% H₃PO₄ + 5.25% NaOCl + 10% Sodium ascorbate (C₆H₇NaO₆) + Adper Single Bond 2; XP: 35% H₃PO₄₊XP Bond; SXP: 35% H₃PO₄₊5.25% NaOCl + 10% Sodium ascorbate + XP Bond. All cavities were restored with a resin composite (Filtek Z250). After removing the root filling from the apical side, teeth were subjected to fluid filtration test for 1 week, 6 and 12 months followed by ×2500 thermocycling after 1st week and 6th months each. Data were analyzed using one-way ANOVA and Dunnet T3 tests (α = 0.05). SEM analyses were carried out after each microleakage evaluation in two random teeth from all groups. Microleakage values in groups SB and XP presented no significant difference in any of the evaluated period (p > 0.05). Microleakage results of SXP (0.01665) group showed significant difference compared to XP (0.03377) and SB (0.03049) groups after 12 months. SSB group (0.00901) showed significantly less microleakage among all other groups (0.01665–0.03377) (p < 0.05). Prior to endodontic treatment, in access cavities, acid etching with 35% H₃PO₄ followed by the application of NaOCl and sodium ascorbate completely destroyed the collagen layer, reducing the microleakage and resin–dentin interface degradation up to 12 months.