A New Comb Circular Polarizer Suitable for Millimeter‐Band Application

This letter presents a new polarizer which has a simple comb structure inside a circular waveguide. The electrical performance of the proposed comb polarizer is optimized by a circular waveguide radius and by the physical parameters of the comb plates. This polarizer is suitable for providing good performance in millimeter‐band application because of its simple structure and low fabrication cost. In our experiments the dual‐band comb polarizer designed in band 1(K) and band 2(Ka) showed good electrical performance without any tuning elements.     

Optimization of Selective Epitaxial Growth of Silicon in LPCVD

Selective epitaxial growth (SEG) of silicon has attracted considerable attention for its good electrical properties and advantages in building microstructures in high‐density devices. However, SEG problems, such as an unclear process window, selectivity loss, and nonuniformity have often made application difficult. In our study, we derived processing diagrams for SEG from thermodynamics on gas‐phase reactions so that we could predict the SEG process zone for low pressure chemical vapor deposition. In addition, with the help of both the concept of the effective supersaturation ratio and three kinds of E‐beam patterns, we evaluated and controlled selectivity loss and nonuniformity in SEG, which is affected by the loading effect. To optimize the SEG process, we propose two practical methods: One deals with cleaning the wafer, and the other involves inserting dummy active patterns into the wide insulator to prevent the silicon from nucleating.     

A New Approach for Built‐in Self‐Test of 4.5 to 5.5 GHz Low‐Noise Amplifiers

This paper presents a low‐cost RF parameter estimation technique using a new RF built‐in self‐test (BIST) circuit and efficient DC measurement for 4.5 to 5.5 GHz low noise amplifiers (LNAs). The BIST circuit measures gain, noise figure, input impedance, and input return loss for an LNA. The BIST circuit is designed using 0.18 μm SiGe technology. The test technique utilizes input impedance matching and output DC voltage measurements. The technique is simple and inexpensive.     

Measurement and numerical simulation of three‐dimensional fiber orientation states in injection‐molded short‐fiber‐reinforced plastics

To determine three‐dimensional fiber orientation states in injection‐molded short‐fiber composites, a confocal laser scanning microscope (CLSM) is used. Since the CLSM optically sections the specimen, more than two images of the cross sections on and below the surface of the composite can be obtained. Three‐dimensional fiber orientation states can be determined by using geometric parameters of fiber images obtained from two parallel cross sections. For experiments, carbon‐fiber‐reinforced polystyrene is examined by the CLSM and geometric parameters of fibers on each cross‐sectional plane are measured by an image analysis. In order to describe fiber orientation states compactly, orientation tensors are determined at different positions of the prepared specimen. Three‐dimensional orientation states are obtained without any difficulty by determining the out‐of‐plane angles utilizing fiber images on two parallel planes acquired by the CLSM. Orientation states are different at different positions and show the shell–core structure along the thickness of the specimen. Fiber orientation tensors are predicted by a numerical analysis and the numerically predicted orientation states show good agreement with measured ones. However, some differences are found at the end of cavity. They may result from the fountain flow effects, which are not considered in the numerical analysis. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 500–509, 2003     

A critical heat flux model based on mass, energy, and momentum balance for upflow boiling at low qualities

A mechanistic modeling of critical heat flux (CHF) in upflow boiling at low qualities is performed. The developed model is based on a physical criterion of CHF occurrence and a mechanism limiting the thermal transport between a stagnant bubbly layer and bulk stream. The mechanism can be mathematically formulated by coupling the equation of limiting mixing mass flux, which is derived from momentum balance equations in two regions, with local mass and energy balance equations on the bubbly layer. The resulting form of the model is represented by a general and straightforward CHF formula involving two empirical constants related to the void fraction and the thickness of the bubbly layer. The predictions agree well with the extensive CHF data of water in uniformly heated tubes.     

The function of bleaching earths in the processing of palm,palm kernel and coconut oils

The results presented in the literature, which attempt to elucidate the mechanisms by which triglyceride oils are bleached by earths, are reviewed. The impact of this work and how the mechanistic proposals affect changes in oil properties are considered, with particular emphasis on the needs of the palm oil processor. Important properties include color, metals and phosphorus content and oxidative stability of the oil. Investigations made in our own laboratories have been aimed at elucidating the effect of varying physical and chemical properties of the bleaching earth on the quality of bleached and deodorized oils. Techniques used in this work are pore-size distribution, surface area, scanning and transmission electron microscopy and a variety of chemical and X-ray analysis methods. The ability to vary such parameters in montmorillonite clays by alteration of process conditions to give materials with specific performance characteristics is demonstrated. Comparisons are made between acid-activated montmorillonites and other clay types.