IPv6 delay and loss performance evolution

Although packet delay and loss are two important parameters of the Internet performance, to the best of our knowledge, the evolution of large‐scale IPv6 delay and loss performance has previously not been studied. In this paper, we analyze more than 600 end‐to‐end IPv6 paths between about 26 testboxes of RIPE Network Coordination Centre over two years, and compare the delay and loss performance over time with their IPv4 counterparts. We present and discuss the measurement methodologies and show that IPv6 paths have a higher delay and loss than their IPv4 counterparts. The main reason for the worse performance stems from IPv6‐in‐IPv4 tunnels rather than from native IPv6 paths and such tunnels are still widely used today. Copyright © 2007 John Wiley & Sons, Ltd.     

How practice produces suboptimal heuristics that render backup instruments ineffective

The operation of machines typically requires attention to instruments that signal the state of the machine. One safeguard against primary instrument malfunction is to provide backup instruments, but this works only if the operators react to malfunction by switching attention to the backups. Little is known about the effect of negative outcomes or feedback on allocation of attention to backup instruments. Four experiments demonstrated that prior practice causes operators of a simulated machine to adapt to instrument malfunction by changing to a suboptimal decision rule rather than by reallocating attention to a different set of instruments. This fallacy appears linked to the operators' failures to notice feedback that they should switch during the simulations and operators' failures to correctly interpret outcome feedback following the simulations. The results raise theoretical questions and warn interface designers not to overrate backup instruments.     

CAD oriented frequency,temperature, and DC bias dependent small‐signal,scalable circuit model of parallel‐plate paraelectric varactors

Simple, CAD compatible small‐signal scalable circuit model for the thin film parallel‐plate ferroelectric varactors is reported. It is based on the measured permittivity and loss tangent of the ferroelectric films along with the fundamental theoretical relationships of ferroelectrics in paraelectric phase. The model makes use of the measured DC field (voltage) at the inflection point of the C‐V curve where the nonlinearity (dC/dV) and the tunability are maximum. Both the capacitance and the equivalent loss resistance (dielectric losses) in the ferroelectric film take into account the low permittivity layers at the boundaries of the nano‐columns of the film. The frequency dependent losses in the top and bottom plates of the varactors and the parasitic inductance of the plates are also taken into account. The model is valid for ferroelectric films having columnar structure. It is useful in wide temperature, DC field, and frequency ranges. © 2008 Wiley Periodicals, Inc. Int J RF and Microwave CAE, 2009.     

User perceptions of ICT impacts in Swedish construction companies: ‘it’s fine,just as it is’

The use of information and communication technologies (ICT) in construction companies has been growing steadily during the last decade. However, few studies inquire into either perceptions of the impact of actual ICT use or perceptions among different occupational groups in construction companies. The aim of the paper is to explore users’ general perceptions of ICT impacts in the post-adoption stage and analyse the implications for construction management practice. A mixed methods approach was used. Quantitative data were collected using a web-based survey both in a major construction company and among medium-sized companies in Sweden. Data from 294 returned completed questionnaires were analysed with t-tests and multiple regression analysis. In addition, participant observations and semi-structured interviews were conducted within the major construction company in order to strengthen the analysis. It can be concluded that respondents are generally fairly satisfied with the ICT. Differences in perceptions among occupational groups can be explained by the nature of work tasks and the original intentions for using ICT as a means of control and calculation. Even if respondents perceive that a further development of ICT could improve competitiveness, they do not want to increase their use of it in their workplaces. They basically think that ‘it is fine, just as it is’. This indicates that a challenge in construction management is to investigate how prevailing and new ICT applications can be used to develop the industry.     

A 21.5/43-GHz dual-frequency balanced Colpitts VCO in SiGe technology

A balanced Colpitts voltage-controlled oscillator (VCO) is designed and fabricated in a commercially available 0.25-/spl mu/m SiGe BiCMOS process. It has the characteristics of the push-push VCO, i.e., the VCO has simultaneously a differential output at a fundamental frequency of 21.5 GHz and a single-ended output at the second harmonic frequency of 43 GHz. A differential tuning technique is applied to reduce the phase noise. The measured phase noise at 1-MHz offset is -113 dBc/Hz at 21.5 GHz and -107 dBc/Hz at 43 GHz. The corresponding output power is about -6 and -17 dBm, respectively, with a 5% tuning range and a 130-mW dc power consumption.     

EU renewable energy support policy: Faith or facts?

The recent EU Commission proposal for promoting the supply of power from renewable energy sources was originally based on a pan-European, harmonised tradable green certificate (TGC) scheme. We suggest, on the basis of a multi-disciplinary analysis, that a pan-EU TGC system is not the way forward for Europe. It is vital that the Commission (and the majority of Member States) avoids implementation of such policy designs put forward by a coalition of vested interests. They should instead look at, and act upon, the available evidence from those countries that have experimented with TGCs (e.g. Flanders, UK and Sweden) and design policies that stand a better chance of meeting the criteria of effectiveness, efficiency and equity. In particular, the policies must enable EU to meet the immense innovation/industrialisation challenge by inducing the development of a capital goods industry that can, eventually, diffuse a broad range of technologies that use renewable energy sources. Only then we can acquire an ability to implement an industrial revolution in the energy system in a way that broadly meets the criteria of effectiveness and dynamic efficiency.     

Opportunities for and limits to Academics as System builders—The case of realizing the potential of gasified biomass in Austria

Gasified biomass is a technology that has the potential to partially replace fossil fuels for the production of heat, electricity, transport fuels, synthetic natural gas (BioSNG) and chemicals. In the context of climate change, biomass gasification is an attractive technology. It is, however, still in the early phase of its diffusion and much of the knowledge resides in the academic sector and in small companies—the technological innovation system (TIS) is in the process of being formed. Austria is one of the leading European countries in this field and much of the development in Austria can be traced to one prominent individual, Professor Hermann Hofbauer at the Technical University of Vienna. The purpose of this paper is to analyze how and the extent to which an individual academic, Professor Hofbauer, has influenced the formation of a TIS centred on gasified biomass in Austria. We find that his impact is multidimensional and significant but that there is also a frictional and intentional resistance that obstructs the commercialisation of the new technology. These sources of resistance go beyond the ability of an individual system builder to handle. Policy makers, therefore, need to add a strong element of system building activities that interact with and supplement those pursued by Professor Hofbauer.     

PBCDD and PBCDF from incineration of waste-containing brominated flame retardants

Brominated organic flame retardants comprise a large, heterogeneous group of compounds that are useful but also potentially damaging to the environment. In this investigation, three common brominated flame retardants were co-combusted with an artificial municipal solid waste in a pilot-scale fluidized bed incinerator. Combustion conditions ensured degradation of the flame retardants, but stable brominated organic compounds such as polybrominated dibenzo-p-dioxins and polybrominated dibenzofurans were formed in the cooling flue gases. The incineration of fuels that contain both chlorine and bromine leads to the formation of a complex mixture of polybrominated/chlorinated dibenzo-p-dioxins and dibenzofurans. More bromination than chlorination was observed in these experiments, and the chlorination levels increased when bromine was added to the fuel. The most favored reactions led to the formation of dibromodichlorodibenzo-p-dioxin and dibromodichlorodibenzofuran. Theoretical calculations show that there is more Br2 than Cl2 in the flue gas when the two halogens are present at equimolar levels, because chlorine is mainly found in the form of HCl. This may explain the higher bromination level. BrCl is also present, which drives the chlorination observed when bromine is added.     

High-resolution capillary zone and gel electrophoresis of structurally similar amphipathic glutathione conjugates based on interaction with beta-cyclodextrins

The tripeptide glutathione is a prominent intracellular constituent that provides protection against genotoxic and carcinogenic electrophiles and is also a component of several biological signal substances. Glutathione conjugates, free glutathione, and glutathione disulfide contain charged amino acid residues, which contribute to solubility in aqueous media. However, the amphipathic nature of glutathione conjugates and the small differences that may distinguish the S substituents, pose analytical problems in their resolution. The present study demonstrates how homologous S-alkyl and S-benzyl conjugates of high structural similarity can be efficiently resolved by capillary electrophoresis. Inclusion of beta-cyclodextrins in the buffer or in a polyacrylamide gel affords baseline separation of the analytes. The separation methods described are applicable to enzyme assays in vitro and to the identification and quantification of glutathione conjugates of importance in toxicology and physiology. The contribution of beta-cyclodextrin to the separation is primarily based on interactions between its hydrophobic cavity and the S-alkyl and S-benzyl groups of the analytes.