Microscale Patterning of Mesoscopic PZN-PT Single Crystal Films by Crystal ion Slicing and Laser-Induced Etching

Advances in the fabrication of solid-solution single crystal relaxor ferroelectrics have made it possible to produce highly efficient piezoelectric crystals, and have attracted renewed interest in the use of these crystals for a new generation of piezoelectric transducers, actuators and sensors. Of particular interest is their incorporation into micro-electromechanical systems (MEMS). In this paper we report on the laser-induced wet chemical etching of lead zinc niobate-lead titanate (PZN-PT) in hydrochloric acid (HCl). Argon-ion laser radiation at power levels up to 4 W is focused to a spot diameter of about 15μm and results in the chemical etching of grooves at patterning speeds up to 5μm/sec. Crystal ion slicing, an ion-implant-based film separation technique, is used in combination with laser etching to form 5 to 10μm-thick patterned and freestanding films for incorporation into micro-electromechanical devices.     

Passive alignment method of polymer PLC devices by using a hot embossing technique

A novel fabrication process using a hot embossing technique has been developed for micromechanical passive alignment of polymer planar lightwave circuit (PLC) devices. With only one step of embossing, single-mode waveguide straight channels and micropedestals for passive aligning are simultaneously defined on a polymer thin film with an accuracy of /spl plusmn/0.5 /spl mu/m. This process reduces the steps for fabricating alignment structures. A fabricated polymer PLC chip and fibers are combined on a v-grooved silicon optical bench (SiOB) in a flip-chip manner. The process provides a coupling loss as low as 0.67 dB per coupling face and a cost-effective packaging solution for various polymer PLC devices.     

Measurement and numerical simulation of three‐dimensional fiber orientation states in injection‐molded short‐fiber‐reinforced plastics

To determine three‐dimensional fiber orientation states in injection‐molded short‐fiber composites, a confocal laser scanning microscope (CLSM) is used. Since the CLSM optically sections the specimen, more than two images of the cross sections on and below the surface of the composite can be obtained. Three‐dimensional fiber orientation states can be determined by using geometric parameters of fiber images obtained from two parallel cross sections. For experiments, carbon‐fiber‐reinforced polystyrene is examined by the CLSM and geometric parameters of fibers on each cross‐sectional plane are measured by an image analysis. In order to describe fiber orientation states compactly, orientation tensors are determined at different positions of the prepared specimen. Three‐dimensional orientation states are obtained without any difficulty by determining the out‐of‐plane angles utilizing fiber images on two parallel planes acquired by the CLSM. Orientation states are different at different positions and show the shell–core structure along the thickness of the specimen. Fiber orientation tensors are predicted by a numerical analysis and the numerically predicted orientation states show good agreement with measured ones. However, some differences are found at the end of cavity. They may result from the fountain flow effects, which are not considered in the numerical analysis. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 500–509, 2003     

Development of geometrically exact new shell elements based on general curvilinear co‐ordinates

In the present study first‐order shear deformable shell finite elements based on general curvilinear co‐ordinates are proposed. For the development of the present shell elements, a partial mixed variational functional with independently assumed strains is provided in order to avoid the severe locking troubles known as transverse shear and membrane lockings. Bubble functions are included in the shape function of displacement to improve the performance of the developed element. The proposed assumed strain four‐ and nine‐node elements based on the general tensor shell theory provide an efficient linkage framework for shell surface modelling and finite element analysis. In the several benchmark problems, the present shell elements with exact geometric representations demonstrate their performance compared to previously reported results. Copyright © 2002 John Wiley & Sons, Ltd.     

A study of CaCO3 fouling with a microscopic imaging technique

The present study introduces a new experimental method to visualize the fouling process of CaCO₃. A mini-channel heat exchanger system with a microscopic imaging technique was developed for real-time visualization of the fouling process. The present study discussed how scale started initially, how scale formed thick layers, and how a small crystal grew into a large one, touching the adjacent one. Detail microscopic images of scale crystals and corresponding fouling resistances were obtained over the entire fouling process. The microscopic observation indicated that the fouling process could be divided into three stages: an induction period, a period of uniform generation of nuclei, and a period of uniform growth of scale. Sudden appearance of numerous small nuclei indicated the end of the induction period, a key event before the rapid increase in the fouling resistance. The present experimental method using microscopic images of the wet fouling process provides a valuable insight on the fouling mechanism.     

A 0.9 V 92 dB Double-Sampled Switched-RC Delta-Sigma Audio ADC

A 0.9 V third-order double-sampled delta-sigma audio ADC is presented. A new method using a combination of a switched-RC technique and a floating switched-capacitor double-sampling configuration enabled low-voltage operation without clock boosting or bootstrapping. A three-level quantizer with simple dynamic element matching was used to improve linearity. The prototype IC implemented in a 0.13 CMOS process achieves 92 dB DR, 91 dB SNR and 89 dB SNDR in a 24 kHz audio signal bandwidth, while consuming 1.5 mW from a 0.9 V supply. The prototype operates from 0.65 V to 1.5 V supply with minimal performance degradation.     

A simple handling technique for mammalian oocytes and embryos during preparation for transmission electron microscopy

Due to their small size, mammalian oocytes and embryos pose unique problems during preparation for transmission electron microscopy. This paper outlines a method which combines protein embedding with centrifugation to locate the specimens on the face of a Beem capsule mould. This method facilitates both the processing of oocytes with minimal loss and rapid location of the specimens within the block for simultaneous sectioning, staining and examination.     

Prediction and quality control of the melt index during production of high-density polyethylene

In polyolefin processes the melt index (MI) is the most important control variable indicating product quality. Because of the difficulty in the on-line measurement of MI, a lot of MI estimation and correlation methods have been proposed. In this work a new dynamic MI estimation scheme is developed based on system identification techniques. The empirical MI estimation equation proposed in the present study is derived from the 1 ^st -order dynamic models. Effectiveness of the present estimation scheme was illustrated by numerical simulations based on plant operation data including grade change operations in high density polyethylene (HDPE) processes. From the comparisons with other estimation methods it was found that the proposed estimation scheme showed better performance in MI predictions. The virtual sensor model developed based on the estimation scheme was combined with the virtual on-line analyzer (VOA) to give a quality control system to be implemented in the actual HDPE plant. From the application of the present control system, significant reduction of transition time and the amount of off-spec during grade changes was achieved     

Fast DCT algorithm with fewer multiplication stages

A novel fast DCT scheme with reduced multiplication stages and fewer additions and multiplications is proposed. The proposed algorithm is structured so that most multiplications tend to be performed at the final stage, which reduces the propagation error that could occur in the fixed-point computation. Minimisation of the multiplication stages can further decrease the error     

Preliminary studies using hybrid mediated electrochemical oxidation (HMEO) for the removal of persistent organic pollutants (POPs).

This study investigates the hybrid mediated electrochemical oxidation (HMEO) technology, which is a newly developed non thermal electrochemical oxidation process for organic destruction. A combination of ozone and ultrasonication processes to the mediated electrochemical oxidation (MEO) process is termed as hybrid mediated electrochemical oxidation. The electrochemical cell was developed in this laboratory. In the present study, several organic compounds, such as phenol, benzoquinone and ethylenediaminetetraacetic acid (EDTA), were chosen as the model organic pollutants to be destructed by the hybrid process. The organic destruction was monitored based on the CO2 generation and total organic carbon (TOC) reduction. The HMEO process was found to be extremely effective in the destruction of all the target organics chosen in this study. The information obtained from this study will provide an insight in adopting this technique for dealing with more recalcitrant organics (POPs).