Repeatedly foldable AMOLED display

In this study, a 5.9‐inch foldable active‐matrix organic light emitting diode (AMOLED) display was developed. A folding test was performed repeatedly. The display survived the folding test (100,000 folds) with a curvature radius of 2 mm. To protect an organic light emitting diode (OLED) against moisture, inorganic passivation layers are provided on the upper and lower sides of the flexible display. Using our transfer technology, high density passivation layers can be obtained. The measured water vapor transmission rate of the layer is 7 × 10^?6 g/m²?day or less, which improves OLED reliability. With these techniques, we have developed a book‐type display, which is repeatedly foldable like a book, and a tri‐fold display including a display area, which is foldable in three.     

Analysis of electro‐optical properties of polymer‐stabilized OCB and the application to TFT‐LCDs

Abstract— A 9‐in. full‐color polymer‐stabilized OCB TFT‐LCD with stable bend alignment in the absence of an electric field was developed. The condition of the polymer stabilization, the characteristics of UV‐curable monomers, and their influence on the configurations of the polymer network in the cell were studied. Possible models of the configuration were proposed and their relationship to the electro‐optical properties was analyzed using a novel simulation method considering the distribution of anchoring effects from both alignment surfaces and the polymer network. It was suggested that a good performance such as high contrast ratio and fast response could be expected in the polymer network originating from newly developed monomers composed of multifunctional LC acrylates due to a relatively weak‐anchoring effect and presumably its localization near the alignment surfaces. By using the newly developed monomers under the optimized polymer‐stabilizing process, a high contrast ratio of 250:1 and fast response nearly equal to that of a conventional OCB cell were achieved.     

The Influence of Rapid Annealing Cycles on the Recrystallisation Behaviour of Cold Rolled Ultra Low Carbon and Low Carbon Steel

For ultra low carbon (ULC) and low carbon steel (LC), the influence of heating rate, annealing temperature, and holding time on the recrystallisation behaviour and the resulting grain size was investigated. For ULC smallest grain sizes of about 9 μm were obtained at the lowest heating rate whereas for LC significant smaller grain sizes of about 5 μm were determined at the highest heating rate. Furthermore, the evolution of the grain size distribution with varying heating rate, annealing temperature, and holding time was studied in dependence of the rolling and normal direction. The state of the as‐hot rolled microstructure as well as the precipitation state exert a strong influence on the development of the recrystallised microstructure along the different directions for both steel grades. The inherent prolonged microstructure due to the cold rolling process is still obvious just after recrystallisation. With ongoing annealing and grain growth, the aspect ratio approaches the equiaxed state. This change proceeds faster for the ULC steel grade. With increasing annealing temperature, the bimodal character of the grain size distribution disappears and the distribution becomes more homogeneous.     

Observation of iron silicide formation by plan-view transmission electron microscopy

The formation and the phase transitions of iron silicide by solid-phase epitaxy have been investigated by means of plan-view transmission electron microscopy, which enables us to observe a clean interface between Fe and Si. Layers of Fe were deposited on Si (100) at room temperature in an ultrahigh vacuum chamber. The sample was annealed in the electron microscope at a temperature between 673 and 1073 K. After annealing at 673 K, FeSi crystallites were formed with various orientations. When the annealing temperature was increased to 973 K, we found that the crystallites suddenly started to coalesce into grains of several hundreds of nanometers in size and polycrystalline beta-FeSi2 was formed. These phase transitions were also confirmed with electron energy-loss spectroscopy.     

Determination of nitroarenes in precipitation collected in Kanazawa, Japan

Eight nitroarenes, 1,3-, 1,6- and 1,8-dinitropyrenes, 1-, 2- and 4-nitropyrenes, 6-nitrochrysene and 2-nitrofluoranthene, in precipitation collected in Kanazawa were determined. The nitroarenes in the precipitation were concentrated onto solid phase extraction cartridges, and identified with high-performance liquid chromatography with chemiluminescence detection. The nitroarene concentrations in the precipitation were in the range 0.016-15 pmol/L, and the nitroarene composition tended to be the same as that in airborne particulates. 1-Nitropyrene in river water and seawater were also determined. 1-nitropyrene concentrations on the days after rain (19-110 fmol/L) were higher than those on the days before rain (4,11 fmol/L). Moreover, 1-nitropyrene concentrations in the river water were much lower than those in the precipitation, but were higher than those in the seawater. These results suggested that the nitroarenes in the precipitation and the river water came from airborne particulates.     

Investigation of gas-liquid interface in atmospheric-pressure micro plasma with solution

An atmospheric-pressure glow-discharge micro plasma in contact with liquid paraffin is stably generated by using a capacitively coupled plasma method with a mesh electrode. When characteristics of the plasma are measured in the boundary between the micro plasma (gas-phase) and liquid paraffin (liquid-phase) using optical emission spectroscopy, spectrum peaks of the emission of CH and C₂ which dissociate from paraffin are observed. The result indicates that solution can feed particles to the plasma at gas-liquid interface and this plasma is accordingly expected to promote an attractive plasma process for creating materials consisting of elements in various solutions.     

Field evaluation of UHF radio propagation for an ITS safety system in an urban environment

Roadside-to-vehicle and vehicle-to-vehicle communication systems have been proposed as part of ITS development to help achieve vehicle safety and realize more secure road traffic environments. In this article we first introduce several typical applications and their radio range requirements for vehicle safety communication systems to clarify the technical point of view. Then we show some field experiment results in an urban area in Tokyo to investigate and verify the radio propagation characteristics and the quality of communications by using a wireless radio prototype system. Finally, we conclude that the current prototype system has potential to fulfill the radio range requirements of vehicle safety communications, but there are still lots of issues that need to be addressed.     

Polonium evaporation and adhesion experiments for the development of polonium filter in lead–bismuth cooled reactors

Fundamental experiments were performed to determine the adhesion characteristics of polonium to different metals and to develop a filter for polonium evaporated from neutron-irradiated LBE. The results of the first experiments suggested that adhesion characteristics are almost the same for stainless steel and nickel metal. The results of the preliminary experiments for a polonium filter suggested that stainless steel mesh with thin wires could effectively collect polonium evaporated from neutron-irradiated LBE. In the experiments, stainless steel wire mesh was used, but from the results of adhesion experiment, it is expected that the same effect can be obtained with wire mesh made of other kinds of metal.     

Two acyl-CoA dehydrogenases of Acinetobacter sp. strain M-1 that uses very long-chain n-alkanes

Two genes encoding acyl-CoA dehydrogenases, acdA and acdB, arranged in tandem, were found in the chromosomal DNA of Acinetobacter sp. strain M-1. AcdA was purified from the parental strain and AcdB was purified from an Escherichia coli strain expressing the cloned gene. The substrate specificities of the two enzymes suggest that AcdA is a medium-chain acyl-CoA dehydrogenase and that AcdB is a long-chain acyl-CoA dehydrogenase. Characterization of n-alkane metabolism in Acinetobacter sp. strain M-1 has revealed parallel pathways as well as enzymes with overlapping specificities in a single pathway. The two acyl-CoA dehydrogenases described here provide another example of the physiological complexity underlying n-alkane utilization.