Transient liquid phase sintering of high-purity mullite for high-temperature structural ceramics

High-purity mullite ceramics, promising engineering ceramics for high-temperature applications, were fabricated using transient liquid phase sintering to improve their high-temperature mechanical properties. Small amounts of ultrafine alumina or silica powders were uniformly mixed with the mullite precursor depending on the silica-alumina ratio of the resulting ceramics to allow for the formation of a transient liquid phase during sintering, thus, enhancing densification at the early stage of sintering and mullite formation by the reaction between additional alumina and the residual glassy phase (mullitization) at the final stage of sintering. The addition of alumina powder to the silica-rich mullite precursor resulted in a reaction between the glassy silica and alumina phases during sintering, thereby forming a mullite phase without inhibiting densification. The addition of fine silica powder to the mullite single-phase precursor led to densification with an abnormal grain growth of mullite, whereas some of the added silica remained as a glassy phase after sintering. The resulting mullite ceramics prepared using different powder compositions showed different sintering behaviors, depending on the amount of alumina added. Upon selecting an optimum process and the amount of alumina to be added, the pure mullite ceramics obtained via transient liquid phase sintering exhibited high density (approximately 99%) and excellent high-temperature flexural strength (approximately 320 MPa) at 1500 °C in air. These results clearly demonstrate that pure mullite ceramics fabricated via transient liquid phase sintering with compositions close to those of stoichiometric mullite could be a promising process for the fabrication of high-temperature structural ceramics used in an ambient atmosphere. The transient liquid phase sintering process proposed in this study could be a powerful processing tool that allows for the preparation of superior high-temperature structural ceramics used in the ambient processing atmosphere.     

Re-evaluation of Radiation-Energy Transfer to an Extraction Solvent in a Minor-Actinide-Separation Process Based on Consideration of Radiation Permeability

ABSTRACT

Absorbed-dose estimation is essential for evaluation of the radiation tolerance of minor-actinide-separation processes. We propose a dose-evaluation method based on radiation permeability, with comparisons of heterogeneous structures seen in the solvent-extraction process, such as emulsions forming in the mixture of the organic and aqueous phases. A demonstration of radiation-energy-transfer simulation is performed with a focus on the minor-actinide-recovery process from high-level liquid waste with the aid of the Monte Carlo radiation-transport code PHITS. The simulation results indicate that the dose absorbed by the extraction solvent from alpha radiation depends upon the emulsion structure, and that from beta and gamma radiation depends upon the mixer-settler-apparatus size. Non-negligible contributions of well-permeable gamma rays were indicated in terms of the plant operation of the minor-actinide-separation process.     

Radiophotoluminescence phenomenon in copper-doped aluminoborosilicate glass

Radiophotoluminescence phenomena have been widely investigated on various types of materials for dosimetry applications. We report that an aluminoborosilicate glass containing 0.005 mol% copper exhibits intense photoluminescence in the visible region induced by X-ray and γ-ray irradiation. The luminescence is assigned to the 3d⁹4s¹ → 3d¹⁰ transition of Cu⁺. The proportionality of the intensity of the induced photoluminescence to the irradiation dose was confirmed up to 0.5 kGy using ⁶⁰Co γ-ray irradiation. Based on the spectroscopic results, a potential mechanism was proposed for the enhancement of the photoluminescence. The exposure to the ionizing radiation generates electron-hole pairs in the glass, and the electrons are subsequently captured by the Cu²⁺ ions, which are converted to Cu⁺ and emit the luminescence. For the glass containing 0.01 mol% copper, the pronounced enhancement of the photoluminescence was not observed because the reverse reaction, ie, the capture of the holes by the Cu⁺ ions, becomes prominent. The photoluminescence induced by the irradiation was stably observed for the glasses kept at room temperature and even for the glasses heat-treated at 150°C. However, the induced photoluminescence could be eliminated by the heat treatment at a temperature at 500°C, and the glass returned to the initial pre-irradiation state. The Cu-doped aluminoborosilicate glass is a potential candidate for use in dosimetry applications.     

Supramolecular Zn(II)-Dipicolylamine-Azobenzene-Aminocyclodextrin-ATP Complex: Design and ATP Recognition in Water

Cyclodextrins (CyDs) are water-soluble host molecules possessing a nanosized hydrophobic cavity. In the realm of molecular recognition, this cavity is used not only as a recognition site but also as a reaction medium, where a hydrophobic sensor recognizes a guest molecule. Based on the latter concept, we have designed a novel supramolecular sensing system composed of Zn(II)-dipicolylamine metal complex-based azobenzene (1-Zn) and 3A-amino-3A-deoxy-(2AS,3AS)-γ-cyclodextrin (3-NH₂-γ-CyD) for sensing adenosine-5′-triphosphate (ATP). 1-Zn showed redshifts in the UV-Vis spectra and induced circular dichroism (ICD) only when both ATP and 3-NH₂-γ-CyD were present. Calculations of equilibrium constants indicated that the amino group of 3-NH₂-γ-CyD was involved in the formation of supramolecular 1-Zn/3-NH₂-γ-CyD/ATP. The Job plot of the ICD spectral response revealed that the stoichiometry of 1-Zn/3-NH₂-γ-CyD/ATP was 2:1:1. The pH effect was examined and 1-Zn/3-NH₂-γ-CyD/ATP was most stable in the neutral condition. The NOESY spectrum suggested the localization of 1-Zn in the 3-NH₂-γ-CyD cavity. Based on the obtained results, the metal coordination interaction of 1-Zn and the electrostatic interaction of 3-NH₂-γ-CyD were found to take place for ATP recognition. The “reaction medium approach” enabled us to develop a supramolecular sensing system that undergoes multi-point interactions in water. This study is the first step in the design of a selective sensing system based on a good understanding of supramolecular structures.     

Eu@C86 isomers: Calculated relative populations

Abstract

Relative populations of four energy-lowest IPR (isolated-pentagon-rule) isomers of Eu@C₈₆ are computed using the Gibbs energy based on characteristics from density functional theory calculations (M06-2X/3-21G?～?SDD entropy term, M06-2X/6-31G*～SDD or B2PLYP(D)/6-31G*～SDD energetics). The calculations confirm that the recently isolated Eu@C₁(7)-C₈₆ species is a major isomer in a relevant temperature region. Relationship to the empty C₈₆ cages is discussed, too.     

Cover Image,Volume 69, Issue 3

The cover image is based on the Mini‐Review Well‐defined, environment‐friendly synthesis of polypeptides based on phosgene‐free transformation of amino acids into urethane derivatives and their applications by Takeshi Endo et al., https://doi.org/10.1002/pi.5952 . Cover image © Takeshi Endo Images.

     

Defocusing image to pattern contact holes using attenuated phase shift masks

The patterning of contact holes by selecting out-of-focus image plane (defocus) using attenuated phase shift masks (APSM) has been studied. Defocus is found to enhance the image modulation at low partial coherence for contact holes with negative local average of mask function. Semi-dense holes up to 130 nm in 8% APSM have been printed by 0.5 μm defocus at a partial coherence of 0.31 using KrF scanner with highest numerical aperture of 0.68. However, these holes were closed with in-focus imaging. Defocus is also found to be beneficial for patterning the pitches that have extensive side lobes with in-focus imaging.     

Synthesis and photosensitivity of acryloylmorpholine copolymers with a pendant (meth)acryloyl group

We have developed new photopolymers that have superior waterproof properties and that can easily interact with polyfunctional acrylate compounds, thus serving as hydrophobic photocrosslinking reagents. Acryloylmorpholine monomers whose homopolymers were less moisture absorbing than the usual water‐soluble polymers but were still water soluble to a good degree, were copolymerized with other acryloyl monomers. We then introduced the photosensitive (meth)acryloyl group to side chains of the resulting polymers. Among six copolymers examined, the copolymers composed of acryloyl morpholine, hydroxyethyl acrylate, ethyl, or methyl methacrylate, and methacryloyl isocyanate were found to have nicely balanced hydrophilicity and waterproof properties, in addition to good compatibility with hydrophobic photocrosslinking reagents. The composite polymers thus obtained were confirmed to be promising photopolymers usable even in a highly humid environment. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 684–692, 2003     

EFFECT OF DEVELOPER PROPERTIES ON PRINT QUALITY

We investigated the dependence of the toner charge-to-mass ratio (q/m) in a two-component electrophotographic developer on the shaking time, toner concentration (T/C), carrier sizes, and the carrier core and the coating materials, as well as the resulting print qualities in terms of print density, background density, tone reproduction, resolution, and dot gain. Four different sizes of spherical ferrite carriers, four different carrier coating materials, and an irregular iron carrier were used with two types of toner: 14 um red toner (NP-4080) and 8 um cyan toner (CLC-500). The q/m measurement by the blow-off method showed that the red toner charge was positive while the cyan toner charge was negative with these carriers. The toner q/m values, which depended on the shaking time and decreased with the increasing T/C were much more affected by the larger carrier and the smaller toner. The carriers which yielded charges in the proper range produced better print qualities than did the other carriers that yielded a toner q/m