On the ‘curiosity’ of electrical self‐heating,static charge and electromagnetic shielding effectiveness from carbon black/aluminium flakes reinforced epoxy‐resin composites

This paper shows the wide application range (such as electrical self‐heating and electromagnetic shielding effectiveness) of composites consisting of conductive carbon black/aluminum flakes (CBA) filler and epoxy insulative matrix. The effect of CBA content on the network structure of epoxy matrix was investigated in detail. Static electrical conductivity increases linearly with the increase of filler concentration at the interface in epoxy composites. The large decrease of the conductivity as a function of the temperature is analyzed in terms of the negative temperature coefficient of conductivity (NTCC) effect. The influence of viscosity, surface energy and barrier highest energy on the NTCC behaviour in the composite is also considered. Based on these results, a new interpretation is proposed to explain the NTCC phenomena by computing the swelling force among conductive phases. The correlations of conductivity during the temperature cycling and activation energy were analyzed. The effects of dynamic ageing at various temperatures on the resistivity are reported. Current–voltage–temperature characteristics for epoxy with different contents of CBA were examined in detail. A model based on the law of energy conservation is proposed to calculate the specific heat and amount of heat dissipation. The static charge of the epoxy–CBA composites was estimated. The correlation between electromagnetic wave‐shielding effectiveness (EMS), conductivity and frequency of epoxy composites with different filler contents is also discussed. Furthermore, the effect of annealing on EMS of epoxy composites was examined. © 2002 Society of Chemical Industry     

Investigation of conductivity characteristics of nitrile butadiene rubber vulcanizates filled with semiconducting carbide ceramic

SiC‐ and B₄C‐filled NBR rubber composites were prepared with various volume fractions of filler by a conventional roll‐mill method. The morphological structures of the NBR–SiC and NBR–B₄C composites were analyzed by scanning electron microscopy. The dependence of room‐temperature volume resistivity (ρ_v) on the concentration of filler in the two systems was studied. In addition, variation in the number of current carriers (n), mobility carriers (μ), dielectric constant (ε), and dielectric loss factor (tan δ) on filler concentration in the two systems were investigated in detail. The applicability of composites as negative temperature coefficient (NTCR) linear thermistors was studied by the dependence of volume resistivity on temperature. The resistivity showed negative temperature dependence and changed linearly with temperature parallel. The conduction mechanism of the conductivity of the two composites was analyzed in terms of the computed activation energy and hopping energy. Change in volume resistivity as a function of frequency for the two systems was also investigated. Finally, the dependence of volume resistivity on applied pressure and possible real applications of these composites as transducers in pressure sensors were also studied. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 2158–2165, 2007     

New PTCR thermistors,switching current,and electromagnetic shielding effectiveness from nanosized vanadium sesquioxides ceramic reinforced epoxy resin nanocomposites

A new polymer nanocomposites of an epoxy resin matrix with randomly dispersed nano‐vanadium sesquioxides (V₂O₃) in various amounts were prepared. The structure of the nanocomposites were characterized by scanning and transmission electron microscopy (SEM and TEM), X‐ray diffraction, hardness, packing factor, extent of filler reinforcement, glass transition temperature, and sound velocity. The percolation threshold in the conductivity of the composites is lesser than 8 wt % and the dielectric constant can reach as high as 103. The resistivity—temperature curve of the composites shows a positive temperature coefficient (PTC) effect. The thermal stability of the composites was examined in terms of thermal gravimetry and differential scanning calorimetry (TG and DTA) and isothermal resistivity–time check. Because of the interfacial interaction among filler particles and the epoxy matrix, the nanocomposites exhibit higher thermal stability. The current–voltage–temperature curves behave as switching current. The temperature increases linearly with the applied voltage which makes this PTC nanocomposites very useful for temperature probe. Finally, electromagnetic interference shielding effectiveness (SE) values have been calculated and measured for the nanocomposites in the frequency range 1–12 GHz. It is found that the SE properties of the nanocomposite improve with increase in wt % of V₂O₃. A maximum SE of 42 dB for V20 sample at 12 GHz has been achieved. These nanocomposites are potentially useful in suppression of electromagnetic interference and reduction of radar signature. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Natural rubber filled SiC and B4C ceramic composites as a new NTC thermistors and piezoresistive sensor materials

A novel electrically conductive composite for NTC thermistor and piezoresistive sensor was successfully fabricated by homogeneously dispersing conductive SiC and B₄C in an insulating natural rubber (NR) matrix. The morphology of the composites was investigated by means of scanning electron microscopy, cross linking density (n), volume fraction of rubber (V_r), and interparticle distance among conductive phases (r_p). The influence of the filler concentrations on the mechanical properties such as modulus of elasticity (E); hardness shore A (H), and elongation at break (EB) were studied in details. The dependences of volume resistivity of NR based composites filled with B₄C and SiC as a function of fillers concentration was investigated. Temperature dependencies of volume resistivity were also measured to examine the possible application of the composites to polymer linear negative temperature (NTC) thermistors. Furthermore, the temperature dependencies of dielectric constant of the composites were studied. For practical application, the thermal stability of the composites was examined by means of resistivity temperature and pressure hysteresis cycle. In parallel, the conduction mechanism of conductivity of the composites was interpreted in terms of the computed the activation and hopping energy. The applicability of the composites to piezoresistive sensor was examined too. The good mechanical properties and thermal stability of NR composites behavior can be utilized for fabricating various electronic devices as NTC thermistors and piezoresistive sensor (i.e. transducers in pressure sensors). POLYM. COMPOS., 29:109–118, 2008. © 2007 Society of Plastics Engineers     

Investigation of Natural Radioactivity in Wadi El Reddah Stream Sediments and Its Radiological Implications

Radiochemistry - Wadi El Reddah has radiation exposure due to the presence of different types of complexed rocks along with a huge sector of Hammamat sedimentary rocks, monzongranites of Gabal El...     

The interrelation among network structures,molecular transport of solvent,and creep behaviors of TiB2 ceramic containing butyl rubber composites

Swelling of polymer composites in solvents has become one of the major problems in the use of polymer composites exposed to petroleum products. As a possible solution to the problem, this experimental study was conducted to examine the potential application of TiB₂ ceramic in butyl rubber (IIR) composites. The effect of TiB₂ content on the curing kinetics of IIR composites was studied using a torque rheometer technique. The effect of TiB₂ on the network structure was investigated in terms of the crosslinking density, interparticle distance between conducting particles, surface tension, glass transition temperature, degree of crystallinity, scanning electron microscopy, and X‐ray analysis. Moreover, the effect of TiB₂ content on the molecular transport of solvent (kerosene) was examined by means of degree of swelling, solvent interaction parameters, volume fraction of rubber, interparticle distance after swelling, penetration rate of solvent, mean diffusion coefficient, cohesive energy density of polymer, standard entropy, standard enthalpy, and standard free energy of IIR composites. It was ascertained that with increasing TiB₂ content the degree of swelling shifts to a lower value. The main reason was interpreted as the introduction of good interface adhesion of TiB₂ with rubber matrix, which tends to block the diffusion of solvent molecules. The effect of TiB₂ content on hardness, tensile strength, Young's modules, and elongation at break is discussed. An apparent steady‐state creep of butyl rubber IIR/TiB₂ composites is evident under different constant stresses at room temperature. The strain rate of steady‐state creep showed a dependence on stress and TiB₂ volume fraction. The stress sensitivity parameter, viscosity coefficient, and activation volume for samples loaded with different content of TiB₂ were estimated. It is apparent that these new composites should be very useful for solvent permeation resistance at high TiB₂ loading level with good mechanical properties. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 2226–2235, 2005     

Infrared Signature of Novel Super-Thermite (Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>/Mg) Fluorocarbon Nanocomposite for Effective Countermeasures of Infrared Seekers

Infrared (IR) guided missiles are real threat; they caused 90% of aircraft damage. Fluorocarbon polymer nanocomposite based on super-thermites can offer superior thermal signature to countermeasure IR guided missile seekers. This study reports on the sustainable fabrication of mono-dispersed colloidal Fe₂O₃ nanoparticles with 3 nm average particle size. Fe₂O₃ nanoparticles were dispersed in acetone for subsequent integration in fluorocarbon polymer. The impact of Fe₂O₃ content on thermal signature was evaluated using (FT-MIR 2–6 μm) spectrophotometer. Nanocomposite polymer with 8 wt% Fe₂O₃ offered an increase in the average intensity of α (2–3 μm) and β (4–5 μm) bands by 50 and 85% respectively to that of reference formulation. Quantification of stimulated emitting species in the combustion flame was conducted using ICT thermodynamic code. The developed nanothermite particles extended the primary reaction zone by 183%. Full discussions about combustion zones with associated exothermic chemical reactions have been represented.     

Thermophysical properties of foliated graphite/nickel reinforced polyvinyl chloride nanocomposites

A novel, polymer‐based foliated graphite/nickel nanocomposites with high thermal conductivity, mechanical properties, and low dielectric constant was developed. The network structure of polyvinyl chloride (PVC) reinforced foliate graphite and nickel nanoparticles (GN) were tested in terms of X‐ray diffraction (XRD), scanning electron microscope (SEM), energy dispersive x‐ray analysis (EDX), and thermal‐gravimetric analyses (TGA). Thermogravimetric analysis revealed a large improvement in the thermal stability of PVC/GN nanocomposites. Thermal conductivity and diffusivity of the composites increased with increasing GN content and temperature. The obtained experimental thermal conductivity result are compared with the existing theoretical models. The measured values of thermal conductivity were in excellent agreement with those calculated from the Agari model. In addition, specific heat, coefficient of thermal expansion (TEC), micro porosity, and crosslinking density (CLD) of composites were investigated. The mechanical properties such as tensile strength, tensile modulus, hardness, and elongation at break of the nanocomposites were improved with inclusion GN which is proportional to GN content. Finally, the dielectric properties of PVC/GN nanocomposites as a function of frequency have been investigated in details. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Green Synthesis of Silymarin–Chitosan Nanoparticles as a New Nano Formulation with Enhanced Anti-Fibrotic Effects against Liver Fibrosis

Background: Silymarin (SIL) has long been utilized to treat a variety of liver illnesses, but due to its poor water solubility and low membrane permeability, it has a low oral bioavailability, limiting its therapeutic potential. Aim: Design and evaluate hepatic-targeted delivery of safe biocompatible formulated SIL-loaded chitosan nanoparticles (SCNPs) to enhance SIL’s anti-fibrotic effectiveness in rats with CCl₄-induced liver fibrosis. Methods: The SCNPs and chitosan nanoparticles (CNPs) were prepared by ionotropic gelation technique and are characterized by physicochemical parameters such as particle size, morphology, zeta potential, and in vitro release studies. The therapeutic efficacy of successfully formulated SCNPs and CNPs were subjected to in vivo evaluation studies. Rats were daily administered SIL, SCNPs, and CNPs orally for 30 days. Results: The in vivo study revealed that the synthesized SCNPs demonstrated a significant antifibrotic therapeutic action against CCl₄-induced hepatic injury in rats when compared to treated groups of SIL and CNPs. SCNP-treated rats had a healthy body weight, with normal values for liver weight and liver index, as well as significant improvements in liver functions, inflammatory indicators, antioxidant pathway activation, and lipid peroxidation reduction. The antifibrotic activities of SCNPs were mediated by suppressing the expression of the main fibrosis mediators TGFβR1, COL3A1, and TGFβR2 by boosting the hepatic expression of protective miRNAs; miR-22, miR-29c, and miR-219a, respectively. The anti-fibrotic effects of SCNPs were supported by histopathology and immunohistochemistry (IHC) study. Conclusions: According to the above results, SCNPs might be the best suitable carrier to target liver cells in the treatment of liver fibrosis.     

A high performance transparent bridge

The high performance transparent bridge (HPTB) is a multiport bridge interconnecting gigabit networks. The provision of specialized hardware support coupled with proper partitioning of bridging protocol entities makes it possible to process frames at very high rates. The HPTB architecture allows concurrent bridging of asynchronous, synchronous and isochronous traffic among heterogeneous networks. It supports both traditional networks, such as variable packet size local area networks (LANs), and cell-based net works, such as distributed queue dual bus (DQDB) and metropolitan area networks (MANs). This device is capable of interconnecting any combination of high speed LANs of rates up to 800 Mbps and/or MANs of rates up to 622 Mbps