Ozonation of CI Reactive Black 5 using rotating packed bed and stirred tank reactor

This study investigates the ozonation of CI Reactive Black 5 (RB5) by using the rotating packed bed (RPB) and completely stirred tank reactor (CSTR) as ozone contactors. The RPB, which provides high gravitational force by adjusting the rotational speed, was employed as a novel ozone contactor. The same ozone dosage was separately introduced into either the RPB or the CSTR for the investigation, while the experimental solution was continuously circulated within the apparatus consisting of the RPB and CSTR. The decolorization and mineralization efficiencies of RB5 in the course of ozonation are compared for these two methods. Moreover, the dissolved and off‐gas ozone concentrations were simultaneously monitored for the further analysis. As a result, the ozone mass transfer rate per unit volume of the RPB was significantly higher because of its higher mass transfer coefficient and gas–liquid concentration driving force. Furthermore, ozonation kinetics was found to be independent of the gravitational magnitude of an ozone gas–liquid contactor. Therefore, the results suggest employing RPBs as ozone‐contacting devices with the advantage of volume reduction. The experimental results, which can be used for further modeling of the ozonation process in the RPB, also show the requirement of correct design for the RPB. Consequently, the present study is useful for the understanding of practical application of RPBs. Copyright © 2004 Society of Chemical Industry     

Synthesis and characterization of a novel proton‐exchange membrane for fuel cells operating at high temperatures and low humidities

The synthesis of a p‐toluidine/formaldehyde (PTF) resin was performed, and the effects of the molar ratio of the individual monomers and the polymerization conditions on the structure of the PTF resin were studied. Fourier transform infrared and ¹³C‐NMR spectra were used to characterize the PTF. Wide‐angle X‐ray diffraction patterns revealed the crystalline structures of various PTFs. Polarized optical microscopy revealed that the molar ratio of the monomers had a strong effect on the crystalline morphologies. A longer polymerization time turned out a polymer with a higher intrinsic viscosity and molecular weight, which led to differences in the proton conductivity. All of the PTFs showed a higher proton conductivity than a commercial Nafion membrane at 90–100°C and 0% relative humidity. The proton conductivity of the PTF series could be improved by sulfonation with sulfuric acid and could be maintained after blending with polyurethane. Pure methanol could be used as a fuel source because of the insolubility and nonwetting properties of PTF in methanol to increase the output current density for a PTF membrane electrode assembly. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

Comparison of image reconstruction by using near‐field and far‐field data for an imperfect conductor

Image reconstruction by using near‐field and far‐field data for an imperfectly conducting cylinder is investigated. A conducting cylinder of unknown shape and conductivity scatters the incident wave in free space and the scattered near and far fields are measured. By using measured fields, the imaging problem is reformulated into an optimization problem and solved by the genetic algorithm. Numerical results show that the convergence speed and final reconstructed results by using near‐field data are better than those obtained by using far‐field data. This work provides both comparative and quantitative information. © 2001 John Wiley & Sons, Inc. Int J RF and Microwave CAE 11: 69–73, 2001.     

Extending UML to model Web 2.0‐based context‐aware applications

Web 2.0 Mashups offer entirely new opportunities for context‐aware application (CAA) developers by integrating Web 2.0 technologies to facilitate interoperability among heterogeneous context‐aware systems. From a software engineering perspective, a visualized approach for Web 2.0‐based CAA modeling is crucial. Current CAA development, however, cannot provide a conceptual model for Web 2.0‐based CAA. Therefore, the development efficiency and potential for reuse are decreased. The UML is a general purpose modeling language with potential for use in many application domains. However, UML often lacks elements needed to model concepts in specific domains, such as Web 2.0‐based CAA modeling. To address the above issues, this study presents the Web 2.0‐based CAA UML profile, a UML profile for modeling Web 2.0‐based CAA. Copyright © 2011 John Wiley & Sons, Ltd.     

Investigation of wall mass transfer characteristics downstream of an orifice

Numerical simulations were performed to determine the effect of Reynolds number and orifice to pipe diameter ratio (d_o/d) on the wall mass transfer rate downstream of an orifice. The simulations were performed for d_o/d of 0.475 for Reynolds number up to 70,000. The effect of d_o/d was determined by performing simulations at a Reynolds number of 70,000 for d_o/d of 0.375, 0.475 and 0.575. The momentum and mass transport equations were solved using the Low Reynolds Number (LRN) K-? turbulence model. The Sherwood number (Sh) profile downstream of the orifice was in relatively good agreement with existing experimental results. The Sh increases sharply downstream of the orifice, reaching a maximum within 1–2 diameters downstream of the orifice, before relaxing back to the fully developed pipe flow value. The Sh number well downstream of the orifice was in good agreement with results for fully developed pipe flow estimated from the correlation of Berger and Hau (1977). The peak Sh numbers from the simulations were higher than that predicted from Tagg et al. (1979) and Coney (1980).     

Dried Blood Spots as Matrix for Evaluation of Valproate Levels and the Immediate and Delayed Metabolomic Changes Induced by Single Valproate Dose Treatment

The immediate and delayed metabolic changes in rats treated with valproate (VPA), a drug used for the treatment of epilepsy, were profiled. An established approach using dried blood spots (DBS) as sample matrices for gas chromatography/mass spectrometry-based metabolomics profiling was modified using double solvents in the extraction of analytes. With the modified method, some of the previously undetectable metabolites were recovered and subtle differences in the metabolic changes upon exposure to a single dose of VPA between males and female rats were identified. In male rats, changes in 2-hydroxybutyric acid, pipecolic acid, tetratriacontane and stearic acid were found between the control and treatment groups at various time points from 2.5 h up to 24 h. In contrast, such differences were not observed in female rats, which could be caused by the vast inter-individual variations in metabolite levels within the female group. Based on the measured DBS drug concentrations, clearance and apparent volume of distribution of VPA were estimated and the values were found to be comparable to those estimated previously from full blood drug concentrations. The current study indicated that DBS is a powerful tool to monitor drug levels and metabolic changes in response to drug treatment.     

Measurement of periodic micro flows using micro-particle image velocimetry with phase sampling

A phase-sampling method has been developed to measure periodic flows at a high temporal resolution using conventional micro-particle image velocimetry (PIV). In this technique, the sampling is set such that each velocimetry dataset represents a unique point in phase of a periodic flow. The flow characteristics over a single cycle are reconstructed from measurements over a number of cycles, thus allowing measurement at a higher temporal resolution than the PIV system. The flow measurements were performed for AC electroosmotic flows and verified with results from the phase-locking technique. The temporal resolution is limited by the shortest camera exposure time and the time separation between laser pulses. The theoretical sampling resolution can be as low as 20 μs for 100 Hz periodic flows. A resolution of 200 μs was obtained in the experiment using 40 velocimetry datasets.     

Enhanced Thermal Stability and Efficiency of Polymer Bulk‐Heterojunction Solar Cells by Low‐Temperature Drying of the Active Layer

This study addresses two key issues, stability and efficiency, of polymer solar cells based on blended poly(3‐hexylthiophene) (P3HT) and [6,6]‐phenyl‐C61‐butyric acid methyl ester (PCBM) by demonstrating a film‐forming process that involves low‐temperature drying (?5 °C) and subsequent annealing of the active layer. The low‐temperature process achieves 4.70% power conversion efficiency (PCE) and ～1250 h storage half‐life at 65 °C, which are significant improvements over the 3.39% PCE and ～143 h half‐life of the regular room‐temperature process. The improvements are attributed to the enhanced nucleation of P3HT crystallites as well as the minimized separation of the P3HT and PCBM phases at the low drying temperature, which upon post‐drying annealing results in a morphology consisting of small PCBM‐rich domains interspersed within a densely interconnected P3HT crystal network. This morphology provides ample bulk‐heterojunction area for charge generation while allowing for facile charge transport; moreover, the P3HT crystal network serves as an immobile frame at heating temperatures less than the melting point (T_m) of P3HT, thus preventing PCBM/P3HT phase separation and the corresponding device degradation.     

Recent Advances in Optical Engineering of Light‐Emitting Electrochemical Cells

Since the first demonstration of light‐emitting electrochemical cells (LECs) in 1995, much effort has been made to develop this technology for display and lighting. A common LEC generally contains a single emissive layer blended with a salt, which provides mobile ions under a bias. Ions accumulated at electrodes facilitate electrochemical doping such that operation voltage is low even when employing high‐work‐function inert electrodes. The superior properties of simple device architecture, low‐voltage operation, and compatibility with inert metal electrode render LECs suitable for cost‐effective light‐emitting sources. In addition to enormous progress in developing novel emissive materials for LECs, optical engineering has been shown to improve device performance of LECs in an alternative way. Light outcoupling enhancement technologies recycle the trapped light and increase the light output from LECs. Techniques to estimate emission zone position provide a powerful tool to study carrier balance of LECs and to optimize device performance. Spectral tailoring of the output emission from LECs based on microcavity effect and localized surface plasmon resonance of metal nanoparticles improves the intrinsic emission properties of emissive materials by optical means. These reported optical techniques are overviewed in this review.