Online grid measurement and ENS detection for PV inverter running on highly inductive grid

Photovoltaic (PV) and other sources of renewable energy are being used increasingly in grid-connected systems, for which stronger power quality requirements are being issued. Continuous grid monitoring should be considered so as to provide safe connections and disconnections from the grid. This letter gives an overview of the methods used for online grid measurement with PV inverters. Emphasis is placed on a method based on the injection of a noncharacteristic harmonic in the grid. Since this injection is regarded as a disturbance for the grid, different issues, i.e., the influence on total harmonic distortion (THD), the accuracy of line impedance measurement and the ENS (German abbreviation of Main Monitoring units with allocated Switching Devices) detection are studied. Laboratory results conducted on an existing PV inverter are presented to demonstrate the behavior of the PV inverter under different grid conditions. Some of the injection parameters are tuned in order to get an accurate measurement of line impedance.     

Pulsed laser deposition of silicon nitride thin films by laser ablation of a Si target in low pressure ammonia

We report the deposition of Si-N films by multipulse excimer laser ( = 308 nm, _FWHM = 30 ns) ablation of Si wafers placed in a slow flow of NH₃ in the pressure range (1 bar-1 mbar). The films are deposited on to a Si collector placed parallel to the Si target. We succeeded in depositing pure amorphous Si₃N₄ films at a pressure of 1 mbar of NH₃. The deposition rate reached a maximum value of 0.2–0.3 nm per pulse. At lower pressures, the deposited films consist of a fine mixture of three amorphous phases (amorphous stoichiometric silicon nitride, amorphous non-stoichiometric silicon nitride and amorphous silicon). The amorphous silicon is prevalent in films deposited at a pressure of several to several tens of bars. Droplets of polycrystalline -Si are sometimes visible on the film surface. The experimental evidence, is analysed with a view to elucidating the participation in the chemical synthesis of the three main stages of the process: the substance expulsion from the target by laser ablation, the transition through the gas of the expulsed substance and it's final impact on the collector. We conclude that silicon nitride is mostly synthesized during the impact on the collector of the flow of the ablated substance.     

SEM investigations of iron surface ion erosion as a function of specimen temperature and incidence angle

Ion bombardment of iron surfaces produced an ion eroded surface microtopography strongly dependent on the incidence angle and specimen temperature. For bombardment temperatures exceeding the self-diffusion temperature, T _d, a microstructural smoothing process due to the thermally activated diffusion effects, assisted by ion bombardment, can be observed by SEM. The role of migrational processes which should be taken into account for a correct interpretation of the final surface topography formed by hot sputtering, was also considered.     

Dense Plasma Injection Experiment at MCX

We present preliminary results of the High Density Plasma Injection Experiment at the Maryland Centrifugal Experiment (MCX). HyperV Technologies Corp. has designed, built, and installed a prototype coaxial gun to drive rotation in MCX. This gun has been designed to avoid the blow-by instability via a combination of electrode shaping and a tailored plasma armature. An array of diagnostics indicates the gun is capable of plasma jets with a mass of 160 μg at 70 km/s with an average plasma density above 10¹⁵ cm⁻³. Preliminary measurements are underway at MCX to understand the penetration of the plasma jet through the MCX magnetic field and the momentum transfer from the jet to the MCX plasma. Data will be presented for a wide range of MCX field parameters, and the prospects for future injection experiments will be evaluated.     

Knowledge-Guided Data-Driven Model With Transfer Concept for Battery Calendar Ageing Trajectory Prediction

<正>Dear Editor, Lithium-ion(Li-ion) battery has become a promising source to supply and absorb energy/power for many energy-transportation applications. However, Li-ion battery capacity would inevitably degrade over time, making its related ageing prediction necessary.     

Synthesis,structural characterization,and photocatalytic properties of iron-doped TiO<Subscript>2</Subscript> aerogels

Fe(III)-doped TiO₂ aerogels are prepared by acid catalyzed sol–gel method followed by supercritical drying, and then heat treatment. Raman spectra together with X-ray diffraction (XRD) and selected area electron diffraction (SAED) patterns of the iron-doped TiO₂ aerogel samples revealed the existence of both anatase and brookite crystalline phases. It was found that the brookite phase formation is favored by the increase of the iron content in the dried samples. XRD measurements show that the lattice constant c of anatase phase decreases with the dopant addition, while the value of a remains essentially unchanged. The microstructure of the investigated samples is relatively compact with small mesopores as revealed from transmission electron microscopy (TEM). The most enhanced photocatalytic activity was exhibited by the TiO₂ aerogel sample with 1.8 at.% Fe(III) whose apparent rate constant of the salicylic acid photodegradation was found to be of almost six times higher than that of Degussa P25.     

Schottky barrier versus surface ferroelectric depolarization at Cu/Pb(Zr,Ti)O3 interfaces

The band bending at Cu/PZT(001) interfaces is investigated by X-ray photoelectron spectroscopy (XPS) for a PZT(001) layer which exhibits initial outwards ferroelectric polarization. Two competitive processes are identified: (a) formation of the Schottky barrier between the ferroelectric and unconnected Cu islands, and (b) coalescence of the Cu islands, realisation of an electrical contact to the ground of the system, inducing the apparent loss of the component of the ferroelectric polarization perpendicular to the sample surface, at least as it manifests in band bending. Three mechanisms are proposed to explain this loss of band bending when a full metal layer connected to ground is formed on the surface: (i) over-compensation of depolarization field in the sub-surface region, (ii) formation of domains with in-plane orientation of the polarization vector and (iii) loss of polarization in the near-surface layers of the ferroelectric due to electrons provided by the metal. These result in a non-monotonous variation of binding energies with the amount of Cu deposited. High resolution transmission electron microscopy and piezoresponse force microscopy confirmed these hypotheses. The XPS data allowed also to derive the surface PZT composition, its evolution with the deposition of copper and the formation of surface compounds.     

X-ray absorption fine structure investigations on heat-treated Cr-doped titania thin films

Chromium-doped titanium oxide thin films were investigated in the as-deposited state and after thermal treatment (723 K for 3 h in air). X-ray diffraction data revealed an improvement in film crystallinity induced by the thermal treatment. Extended X-ray absorption fine structure data revealed similar atomic neighboring around Cr atoms in both as-deposited and annealed samples. A lattice contraction of ~ 2% is observed in the annealed samples. The 67% enhancement of the amplitude of the Cr 1 s X-ray absorption fine structure pre-edge peak after thermal treatment, which is a sign of “dipole-forbidden” 1 s → 3 d transitions, suggests strong alteration in the number of Cr 3 d vacancies, in spite of similar Cr local environment in the two kinds of investigated samples. We discuss here the Cr⁺ → Cr⁴⁺ and Cr²⁺ → Cr⁶⁺ changes induced by thermal treatment, and/or the evolution in local structures without inversion center.Refractive index dispersion spectra in the visible wavelength domain allowed us to compute the values of the dispersion energy, the single-oscillator energy and the coordination number of Ti atoms in both as-deposited and annealed samples.