Stabilization of bioethanol recovery with silicone rubber‐coated ethanol‐permselective silicalite membranes by controlling the pH of acidic feed solution

In order to produce highly concentrated bioethanol by pervaporation using an ethanol‐permselective silicalite membrane, techniques to suppress adsorption of succinic acid, which is a chief by‐product of ethanol fermentation and causes the deterioration in pervaporation performance, onto the silicalite crystals was investigated. The amount adsorbed increased as the pH of the aqueous succinic acid solution decreased. The pervaporation performance also decreased with decreasing pH when the ternary mixtures of ethanol/water/succinic acid were separated. Using silicalite membranes individually coated with two types of silicone rubber, pervaporation performance was significantly improved in the pH range of 5 to 7, when compared with that of non‐coated silicalite membranes in ternary mixtures of ethanol/water/succinic acid. Moreover, when using a silicalite membrane double‐coated with the two types of silicone rubber, pervaporation performance was stabilized at lower pH values. In the separation of bioethanol by pervaporation using the double‐coated silicalite membrane, removal of accumulated substances having an ultraviolet absorption maximum at approximately 260 nm from the fermentation broth proved to be vital for efficient pervaporation. Copyright © 2005 Society of Chemical Industry     

Zeolite synthesis from paper sludge ash with addition of diatomite

BACKGROUND: This study aimed to investigate the synthesis of zeolites from paper sludge ash (PSA) with added diatomite to remove both NH₄⁺ and PO₄^3? for water purification. The PSA had low Si and significant Ca contents. Four types of diatomite: white (T‐W) and brown (T‐B) from deposits of marine origin in Takanosu, and white (S‐W) and gray (S‐G) from lacustrine deposits in Shonai, were added to NaOH solution to increase the Si content and thereby synthesize zeolites with high cation exchange capacity (CEC). RESULTS: The order of the amounts of Si extracted from the diatomite to the alkali solution was S‐W > T‐W = T‐B > S‐G, which correlates with the amorphous SiO₂ content of diatomite. The original ash without addition of diatomite yielded hydroxysodalite with CEC of about 1.0 mmol g^?1. For all samples, the addition of diatomite to the solution yielded zeolite‐P with a higher CEC, but the addition of excess Si inhibited the synthesis of zeolite‐P, and the CEC of the product was low. A product with high CEC including zeolite‐P was obtained in a solution with around 500 mmol L^?1 of Si concentration, and had the ability to remove both NH₄⁺ and PO₄^3?. CONCLUSION: Diatomite has the potential for used as an additive for the synthesis of high CEC zeolite from PSA. The product with zeolite‐P exhibited relatively high CEC, capacity for NH₄⁺ uptake, and the ability to remove PO₄^3? by precipitation, which is preferable for water purification applications. Copyright © 2008 Society of Chemical Industry     

The influence of exercise intensity on sweating efficiency of the whole body in a mild thermal condition

The photodegradation of seven carbamate pesticides (bendiocarb, isoprocarb, promecarb, ethiofencarb, furathiocarb, fenoxycarb and pirimicarb), in aqueous solution, has been examined by GC-MS. The most general result was formation of the corresponding phenols. Irradiation of isoprocarb and promecarb also resulted in photo-Fries rearrangement to ortho- and para-hydroxybenzamides. In the case of ethiofencarb photocleavage of the carbon-sulfur bond gave 2-methylphenyl methylcarbamate as main product. Likewise, N-S bond cleavage occurred upon irradiation of furathiocarb, to allow the formation of the carbamate insecticide carbofuran, butyl methylcarbamate and carbofuranphenol. Under similar conditions, fenoxycarb gave p-phenylphenol and 2-hydroxydibenzofuran, through primary homolysis of the aryloxy-methylene bond. Finally, pirimicarb gave rise to 2-formylamino-5,6-dimethylpyrimidin-4-yl dimethylcarbamate.     

Arterial oxygen desaturation during non-sedated diagnostic upper gastrointestinal endoscopy

We studied oxygen saturation (SaO2) using a pulse oximeter in 120 patients undergoing non-sedated diagnostic upper gastrointestinal endoscopy. The baseline SaO2 was 98.3 +/- 1.0%. During the procedure, absence of oxygen desaturation (SaO2 > or = 95%) was found in 56%, mild oxygen desaturation (95% > SaO2 > or = 90%) in 35%, and severe oxygen desaturation (SaO2 < 90%) in 9%. Age (p = 0.56), gender (p = 0.47), smoking (p = 0.35), hemoglobin level (p = 0.52), body mass index (p = 0.27), or total endoscopy time (p = 0.72) was not related to the degree of oxygen desaturation. These results suggest that oxygen desaturation is frequently observed during non-sedated diagnostic upper gastrointestinal endoscopy although severe oxygen desaturation, which may induce rare but serious cardiopulmonary events, is not common. Furthermore, we cannot predict in which patients desaturation will occur. We therefore recommend continuous monitoring of arterial oxygenation in all patients during the procedure.     

Temperature Dependence of Thermal Reflection Behavior of Al2O3–TiO2 Multilayer Thermal Energy Window Coating

An Al₂O₃–TiO₂ multilayer-coated sapphire thermal energy window coating has been fabricated using an ultra-high-speed vacuum sputtering method. Thermal reflection spectra of the coated material in the wavelength range from 1.43 to 3.33 μm are measured in ambient air at temperatures of 298, 773, and 1173 K. The result shows that the light reflectance of ∼70% is achieved using a layered structure and this performance continues up to 1173 K. Thermal reflection energy of the coated material at T =1173 K is estimated to be about three times higher than that of uncoated sapphire, suggesting the potential of this coating to control thermal radiation energy.     

Fabrication of Transparent, Sintered Sc2O3 Ceramics

We report here the fabrication of transparent Sc₂O₃ ceramics via vacuum sintering. The starting Sc₂O₃ powders are pyrolyzed from a basic sulfate precursor (Sc(OH)_2.6(SO₄)_0.2·H₂O) precipitated from scandium sulfate solution with hexamethylenetetramine as the precipitant. Thermal decomposition behavior of the precursor is studied via differential thermal analysis/thermogravimetry, Fourier transform infrared spectroscopy, X-ray diffractometry, and elemental analysis. Sinterability of the Sc₂O₃ powders is studied via dilatometry. Microstructure evolution of the ceramic during sintering is investigated via field emission scanning electron microscopy. The best calcination temperature for the precursor is 1100°C, at which the resultant Sc₂O₃ powder is ultrafine (∼85 nm), well dispersed, and almost free from residual sulfur contamination. With this reactive powder, transparent Sc₂O₃ ceramics having an average grain size of ∼9 μm and showing a visible wavelength transmittance of ∼60–62% (∼76% of that of Sc₂O₃ single crystal) have been fabricated via vacuum sintering at a relatively low temperature of 1700°C for 4 h.     

Preparation of Aragonite Whiskers

A simple synthetic method for preparing aragonite whiskers has been developed. A suspension of CaCl₂-MgCl₂-Mg(OH)₂ with pH ∼9 has been prepared by adding Ca(OH)₂ to MgCl₂ aqueous solution. CaCO₃ whiskers (aragonite phase) have been prepared easily by blowing CO₂-containing gas into the suspension. The whiskers have high aspect ratios ranging from 20 to 80 with diameters of 0.5–1 μm .     

An Application of Silica‐Based Monolithic Membrane Emulsification Technique for Easy and Efficient Preparation of Uniformly Sized Polymer Particles

Summary: Uniformly sized polymer particles were prepared by an emulsification and polymerization technique utilizing a silica monolithic membrane, namely the “silica monolithic membrane emulsification technique”. In this paper, we utilized silica monolithic membrane as a device for the preparation of uniformly sized polymer particles. A mixture of monomers, diluents and oil‐soluble initiator was emulsified into a continuous medium through the silica monolithic membrane and polymerized. The particles obtained had a higher size uniformity than that of particles prepared by previously reported membrane emulsification techniques, such as the Shirasu Porous Glass (SPG) emulsification technique. Through the silica monolithic membrane emulsification technique, we could prepare particles having availability as a possible packing material for solid‐phase extraction (SPE) and high performance liquid chromatography (HPLC).

SEM photograph of silica particles prepared through capillary plate membrane.     

Two‐way multi‐view 2‐D/3‐D display combining LC lens and HVxDP panel using novel pixel arrangement

We have developed a two‐way multi‐view 2‐D/3‐D display combining a liquid crystal lens and horizontally and vertically x times‐density pixels (HVxDP) arrangement. The two‐way multi‐view display features the same display resolution in 2‐D and 3‐D modes and a quite small color moiré for landscape and portrait, respectively, when using the HVxDP arrangement. In this paper, we realized suitable 3‐D properties for achieving a good balance between 3‐D moiré and 3‐D crosstalk for landscape and portrait by a two‐way liquid crystal lens with two kinds of focal lengths for the edge part and the center part of the lens.