Power swing analysis in a future metropolitan electric power system on a contingent trip of cryogenic high-power cables

A cryogenic power cable is expected to be capable of carrying bulk power as a main transmission line in a future metropolitan electric power system. It is important to establish a strategy of how to sustain power supply when such a highly densified power supply route trips from the network due to contingency. It is proposed here that the bulk power transmitted by the cryogenic cable could be distributed into the parallel conventional transmission lines by suitable circuit breaker operations in the system. In this process, power-flow routes are forced to be changed with a remarkable modification in the system configuration. In this paper, the power swings associated with the large power-flow change following contingent faults are analyzed by means of a transient network analyzer. It is found that the proposed system modification could be realized without any harmful power swing if the parameters in generators as well as in control devices have conventional magnitudes. It is shown also by simulations that the margin to occurrence in an unstable power swing is left sufficient even if the parameters deviate somewhat from the present magnitudes.     

EXPANSION AND STRESS RELAXATION OF EXPRESSED CAKE

Expansion and stress relaxation of expressed cake are discussed.

The expansion process of expressed cake after release of load is very similar to consolidation of solidndashliquid mixtures, although a liquid flow in the expansion process is opposite in direction to that in consolidalion. This process can be analyzed well by use of the Terzaghi Voigt combined model. It is shown that the rate of primary deformation in expansion is much smaller than that in consolidation under the same change in compressive pressure. It is also found that the ratio of secondary deformation to total deformation in expansion is much larger than that in consolidation.

Stress relaxation of expressed cake, which is observed when expression is stopped before attaining an equilibrium compression state of a material, can be explained by use of a consolidation and expansion theory. In the relaxation process, local expansion appears near the drainage surface while local consolndash idation appears near the center of the cake. The equilibrium cake stress is uniquely determined by the average consolidation ratio when the expression is interrupted.     

Numerical analyses of high‐beta spherical tokamaks with varied elongation

The effect of plasma elongation on the second‐stable spherical tokamak (ST) was numerically studied using the experimentally measured pressure and current profiles of ultrahigh‐beta STs. The maximum beta of ST over 50% was obtained in the TS‐3 ST/CT experiment by applying an external toroidal field to an FRC. It was found that the marginal beta for the ballooning instability increased with the plasma elongation κ of ST. The elongated STs with κ > 2 have the magnetic shear (S)–pressure gradient (α) profiles located in the second‐stable regime for the ballooning mode and the stability margin increased with κ. The close relation between the absolute minimum‐B profile and the second stability was documented. The effect of elongation on maximum beta was observed to saturate when κ exceed 3, indicating that the optimized elongation for high‐beta STs is located around 2 < κ < 3. © 2006 Wiley Periodicals, Inc. Electr Eng Jpn, 155(4): 1–6, 2006; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20132     

Evaluation of static and dynamic fracture toughness in ductile cast iron

Crack extension behavior and fracture toughness of ductile cast iron were examined by three-point bend tests, where various detection methods of crack initiation under static and dynamic loading conditions were adopted. Loading on the specimens was interrupted at various displacement points, and the final fracture surfaces of the specimen were observed via scanning electron microscopy (SEM). Crack-tip opening displacement (CTOD) obtained under the dynamic loading condition was smaller than that under the static loading condition in ferritic ductile cast iron, and CTOD additionally decreased with increasing pearlite content in the matrix. The relationship between J (ΔC) obtained by the compliance changing rate method and J(R) established by the intersection of the crack extension resistance curve and the theoretical blunting line varied with pearlite content. The average value of .J(ΔC) and J(R), that is J (mid), was proposed to define the fracture toughness of ductile cast iron; J (mid) was considered to be a reasonable measure for the fracture toughness of ductile cast iron, irrespective of loading condition and the pearlite content in the matrix.     

A 3-V, 2%-mW multibit current-mode ΣΔ DAC with 100 dBdynamic range

The area ratio of analog to digital for mixed-mode chip has been inversely proportional to the process design rule for a given dynamic range objective, in contradiction to the LSI trend. This paper presents a design approach to realize a high degree of size reduction with process design rules for analog circuitry and a signal processing architecture for digital circuitry. A five-level current-mode ΣΔ digital-to-analog converter (DAC) system reveals full scale total harmonic: distortion plus noise (THD+N) of -90 dB and dynamic-range of 100 dB at 3 V (low power of 22 mW). Analog-area down-scaling can be accomplished by this architecture to be 1.09 mm², using 0.6-μm double-poly double-metal (DPDM) CMOS. For the digital filter, a pipeline instruction sequence with multiplierless architecture also gives small area of 1.98 mm²     

Calbindin-D 28 kD and parvalbumin in the horizontal cells of rat retina during development

Restless legs syndrome (RLS) and periodic limb movements in sleep (PLMS) are disorders that are common and disturbing to uremic patients. The treatment of these is problematic. Eight patients on chronic hemodialysis and continuous peritoneal dialysis completed a double-blind placebo-controlled crossover study using incremental doses of pergolide up to 0.25 mg at bedtime for treatment of RLS and sleep disruption. Five patients (62.5%) noted subjective improvement in restless legs symptoms and sleep quality. Objective results were improved only slightly by treatment. The percentage of the first hour in bed during which leg movements occurred decreased from 20.5 +/- 6.0 to 11.5 +/- 3.3, p < 0.05. However, findings during sleep were less positive. The following measures were not significant between placebo and treatment: leg movements per hour of sleep [53.7 +/- 22.3 vs 35.8 +/- 11.8 (p = 0.2)]; and percentage of sleep time spent with leg movements [5.5% +/- 3.2 vs 4.4% +/- 1.4 (p = 0.37)]. Patients continued to have very disrupted sleep, and we could not document an objective improvement in sleep architecture. Thus, although pergolide at the dose of 0.25 mg at bedtime provided subjective improvement in symptoms of restless legs and quality of sleep, and objectively decreased leg movements during the first hour in bed, objectively sleep continued to be disrupted. In this small patient group, the response to pergolide was not uniform, and further investigation is required to test effectiveness at higher doses.     

Acrylic nonaqueous dispersion using butylated melamine-formaldehyde resin as dispersant

A series of acrylic nonaqueous dispersions were prepared by using various kinds of butylated melamine–formaldehyde (BMF) resins as dispersant. The functional group composition of BMF to form stable dispersion was butoxy group more than 13 mol/BMF 1 mol, and methylol group ranged from 1 to 2.5 mol/BMF 1 mol. It is concluded that the anchoring of BMF to acrylic copolymer was due to the formation of covalent bond between methylol group in BMF and hydroxy group in acrylic copolymer.     

D.s.c. investigation of the states of water in poly(vinyl alcohol-co-itaconic acid) membranes

The state of water in water-swollen poly(vinyl alcohol-co-itaconic acid) membranes, having various water contents from 0.31 to 0.83, was investigated by d.s.c. measurements and compared with those in water-swollen poly(vinyl alcohol) membranes. The amount of freezing water in the membranes was estimated by use of a relationship between the phase transition temperature and the enthalpy of the crystallization of supercooled water. The melting temperature of the water in the membranes immersed in urea and NaCl 0–2 mol l^?1 aqueous solutions was also determined by d.s.c. analysis. The present study proposes a method for estimating the solubilities of urea and NaCl in both of the freezing and the non-freezing water using the melting point depression of the freezing water in the membranes immersed in the solute solution.