Transient simulation of heterojunction photodiodes-part II:analysis of resonant cavity enhanced photodetectors

The high-speed response properties of resonant cavity enhanced (RCE) photodetectors have been investigated. The limitations on the high-speed performance of photodiodes and the advantages of RCE-detection are discussed. Transient response of heterojunction photodiodes under pulsed optical illumination has been simulated using the method described in Part I. Results on conventional AlGaAs/GaAs and RCE GaAs/InGaAs heterojunction p-i-n photodiodes are presented. For small area detectors, almost 50% bandwidth improvement along with a two-fold increase in efficiency is predicted for RCE devices over optimized conventional photodiodes. A nearly three-fold enhancement in the bandwidth-efficiency product was shown     

Ho:CaF(2) solid-state saturable-absorber Q switch for the 2-µm Tm,Cr:Y(3)Al(5)O(12) laser

The holmium-doped calcium fluoride (Ho:CaF(2)) crystal was shown to be an effective solid-state saturable-absorber Q-switch for a flash-lamp-pumped Tm,Cr:Y(3)Al(5)O(12) laser at 2.017 μm. With a 1-cm-thick Ho(0.5%),Er(5%):CaP(2) saturable absorber and a 6.3% output coupler, a single Q-switched laser pulse of 51 mJ in energy and 60 ns in duration was obtained at a flash-lamp input energy of 85 J. With a 14.6% output coupler, a typical Q-switched laser pulse of 84 mJ and 82 ns was observed.     

A gantry-based tri-modality system for bioluminescence tomography

A gantry-based tri-modality system that combines bioluminescence (BLT), diffuse optical (DOT), and x-ray computed tomography (XCT) into the same setting is presented here. The purpose of this system is to perform bioluminescence tomography using a multi-modality imaging approach. As parts of this hybrid system, XCT and DOT provide anatomical information and background optical property maps. This structural and functional a priori information is used to guide and restrain bioluminescence reconstruction algorithm and ultimately improve the BLT results. The performance of the combined system is evaluated using multi-modality phantoms. In particular, a cylindrical heterogeneous multi-modality phantom that contains regions with higher optical absorption and x-ray attenuation is constructed. We showed that a 1.5 mm diameter bioluminescence inclusion can be localized accurately with the functional a priori information while its source strength can be recovered more accurately using both structural and the functional a priori information.     

Optical sensing of biomolecules using microring resonators

A biosensor application of vertically coupled glass microring resonators with Q/spl sim/12 000 is introduced. Using balanced photodetection, very high signal to noise ratios, and thus high sensitivity to refractive index changes (limit of detection of 1.8/spl times/10/sup -5/ refractive index units), are achieved. Ellipsometry and X-ray photoelectron spectroscopy results indicate successful modification of biosensor surfaces. Experimental data obtained separately for a bulk change of refractive index of the medium and for avidin-biotin binding on the ring surface are reported. Excellent repeatability and close-to-complete surface regeneration after binding are experimentally demonstrated.     

Characteristics of p-Ge/N-GaAs heterojunctions grown by molecular beam epitaxy

Reports the nearly ideal electrical characteristics of p-Ge/N-GaAs heterojunction diodes grown by molecular beam epitaxy. The temperature and device size dependencies of the current-voltage characteristics have been investigated. At room temperature, unity ideality factor has been demonstrated over almost six decades of current.<>     

Fuel bioadditive production by chitosan/sulfosuccinic acid catalytic membrane

Global warming is one of the biggest environmental problems of late. The use of renewable raw material resources as biomass and its conversion into alternative energy resources have attracted considerable attention during the recent years. Ethyl levulinate (EL) is a kind of fuel bioadditive for use in diesel and biodiesel engines, which is produced by the esterification of ethanol and levulinic acid. In the present study, sulfosuccinic acid (SSA) catalysts supported on chitosan catalytic membrane is used for the synthesis of EL. The effects of temperature, catalyst amount, and molar feed ratio were studied.     

Compensating the effects of DC bias lines on terahertz photomixer antennas using resistively loaded lines

This paper proposed a method, namely resistively loaded lines (RLL), to compensate the effects of the DC bias lines after investigating its effects on several types of antennas for terahertz photomixers. The RLL is formed by placing lumped resistances periodically on the DC bias line in order to cease the leakage current virtually, which cause a significant amount of distortion on the antenna performance. The simulation results of the dipole, folded dipole, log-periodic, and spiral antennas show that RLL almost removes the effects of the bias lines and improves the antenna radiation resistance and radiation pattern notably compared with that of the commonly used bias line types, such as coplanar stripline and photonic bandgap type bias lines.     

Thieno[3,2-b]thiophene as π-bridge at different acceptor systems for electrochromic applications

Benzoselenadiazole, quinoxaline and thieno[3,2-b]thiophene are the units preferred in conducting polymers due to their electrochemical properties. There are no reports in the literature on polymers containing both moieties. In this study, novel benzoselenadiazole, quinoxaline and thieno[3,2-b]thiophene based monomers; 4-(3a,6a-dihydrothieno[3,2-b]thiophen-2-yl)-7-(thieno[3,2-b]thiophenyl)benzo[c][1,2,5]selenadiazole (BSeTT) and 2,3-bis(3,4-bis(decyloxy)phenyl)-5,8-dibromo-2,3-dihydroquinoxaline (QTT) were synthesized via Stille Coupling and polymerized electrochemically. These polymers were characterized in terms of their spectroelectrochemical and electrochemical properties by cyclic voltammetry and UV–Vis–NIR spectroscopy. Spectroelectrochemistry analysis of PBSeTT revealed an electronic transition at 525 nm corresponding to π–π* transition with a band gap of 0.93 eV whereas PQTT revealed electronic transitions at 440 and 600 nm corresponding to π–π* transitions with a band gap of 1.30 eV. Electrochromic investigations showed that PBSeTT has gray color PQTT switching between green and gray. Switching time of the polymers was evaluated by a kinetic study upon measuring the percent transmittance (%T) at the maximum contrast point.     

Geometric mean vs. Arithmetic mean in extrusion residence time studies

Geometric mean residence time was compared with the arithmetic mean residence time for a residence time distribution study conducted on a twin‐screw extruder using a salt tracer and electrical conductivity measurements. Electrical conductivity of the cornmeal melt was measured at the die exit. All RTD curves obtained during the study were skewed to the right with very long tails that resulted in inflated arithmetic mean residence times. In order to alleviate the problem of long tails, different approaches were considered. Among these approaches, logarithmic transformation of the time scale to calculate the geometric mean residence time was shown to best represent the residence time distribution in terms of mean residence time and spread of the RTD. The log transformation of the time scale alleviates the problem of inappropriate shifting of the mean residence time due to long tails. The difference between the upper limits and lower limits for the log transformed data was found to be more appropriate to define the spreads of the distributions as the untransformed data resulted in quite variable spreads.