Calf massager: Intervention for body muscle discomfort during prolonged standing

Many occupations require workers to stand for long periods of time without proper interventions, which causes discomfort in the back and lower limbs. Therefore, this study aims to assess the effectiveness in alleviating body muscle discomfort during prolonged standing through the use of a calf massager. This study was conducted among male workers at a manufacturer with production line workers and the list was obtained from the HR Department and simple random sampling was done by number categorization. A total of 100 respondents (50 respondents for both the control and the experimental groups) participated in this study. The experiment took place in a room with a similar setup for the production line. Each respondent was requested to perform the simulated task for 2 hr. For the experimental group, the calf massager was turned on every 15 min. At every 15‐min interval after turning on the calf massager, respondents from both groups were required to evaluate their discomfort level on a Borg's scale CR‐10 questionnaire. The results showed that the level of body discomfort among respondents in the experimental group reduced (20–30%) compared with that of the control group. Multivariate analysis results revealed that the discomfort rating for the lower back, knees, thighs, calves, and feet was significantly lower (p < .05) among the experimental group compared with the control group. For lower body parts, the lower back region was statistically significant (p < .05) at the 90th, 105th, and 120th min; the thigh region was statistically significant (p < .05) at the 120th min; the knee region was statistically significant (p < .05) at the 105th and 120th min; the calf region was statistically significant (p < .05) at all minute intervals except the 15th and 45th min, while the feet region, was statistically significant at the 105th and 120th min. Therefore, this study indicates that calf massage treatment is capable of reducing body muscle discomfort during prolonged standing and highlights the significance of calf massage.     

热声制冷机及其改进实验研究

热声制冷作为一种很有前途的制冷方法，在国内外相关领域引起了极大兴趣。热声制冷机由声发生器、共振管、板叠及高、低温换热器等部分组成。对声驱动器的振动膜及其冷却系统、气体弹簧系统、高、低温换热器进行了初步改进，使制冷机冷端温降从原来的12℃提高到27℃左右，这是目前国内报道的最大温降。     

Scattering of an induced surface electromagnetic field by fatiguecracks in ferromagnetic metals

In crack detection and sizing by the alternating current field measurement technique, U-shaped wires or coils excited by a high-frequency AC current source can be used to induce the surface field in the workpiece. The authors present a modeling technique for the interaction of a fatigue crack in a ferromagnetic metal with the surface field resulting from an inducer with two U-shaped wires. This work is an extension of a previous modeling technique to have developed for infinitely long (one-dimensional) cracks. In the present technique, the boundary of the fatigue crack is approximated by a circular arc, leading to a formulation for an efficient computation of the field-flaw interaction. Various numerical and experimental results supporting the modeling and illustrating the behavior of the magnetic field and electric potential at the metal surface around circular-arc cracks are presented     

High frequency capacitance measurements on metal–insulator–semiconductor structures in thermal non-equilibrium condition

We simulate the charge carrier traffic between the energy bands and the interface states in structures like Al/SiO₂/6H–SiC, Al/diamond/Si and Al/SIPOS/Si to explain their high frequency capacitance–voltage behavior. The structures have in common that traditional electrical measurement techniques performed at room temperature are prone to thermal non-equilibrium effects. This can result in large errors in the interface data extracted from such studies when thermal equilibrium conditions are assumed. In this work, high frequency capacitance–voltage data are compared to numerical simulations which include such thermal non-equilibrium conditions to enable more accurate estimates of interface state parameters in above-mentioned structures.     

基于径向矢量的不变性形状分类方法

介绍一种利用径向矢量提取形状特征的方法，着重于分析二维图形的不变性，提出一种带有方向因子的径向矢量描述，该矢量以图形边界弧长为自变量，完整地刻画了图形特点，克服了非凸图形识别中存在的多义性，以归一化的特征矢量的输入，采用三层神经网络为分类器，在字符及军事目标不变性识别中取得了令人满意的结果。     

Optical and electrical characterization of CdS thin films

Thin CdS films have been grown by chemical bath (CdCl₂, thiourea, ammonia) deposition (CBD) on SnO₂ (TO)-coated glass substrate for use as window materials in CdS/CdTe solar cells. High-resolution transmission electron microscopy revealed grains with an average size of 10 nm. The structure was predominantly hexagonal with a high density of stacking faults. The film crystallinity improved with annealing in air. Annealing in a CdCl₂ flux increased the grain size considerably and reduced the density of stacking faults. The optical transmission of the as-deposited films indicated a band gap energy of 2.41 eV. Annealing in air reduced the band gap by 0.1 eV. Annealing in CdCl₂ led to a sharper optical absorption edge that remained at 2.41 eV. Similar band gap values were obtained by photocurrent spectroscopy and electroabsorption spectroscopy (EEA) using an electrolyte contact. EEA spectra were broad for the as-deposited and air-annealed samples, but narrower for the CdCl₂-annealed films, reflecting the reduction in stacking fault density. Donor densities of ca. 10¹⁷ cm ^–3 were derived from the film/electrolyte junction capacitance.     

A mashup based framework for multi level healthcare interoperability

Healthcare delivery is evolving from disease-centered to patient-centered care delivery where patients are active participants in their healthcare delivery. This calls for more communication and collaboration among all healthcare actors. There is also an increasing demand for personalized healthcare systems that provide effective information management, facilitate communication and collaboration, and support applications to meet user requirements. To address these challenges, we need to advance the integration and interoperability of healthcare applications in a controlled manner. Drawing upon a conceptual model from a collaborative care case study, we identified a set of interoperability requirements and developed a Mashup based interoperability framework. Our framework allows patients and other healthcare actors to engage in collaborative processes through online applications facilitated by mashups. We then use proof-of-concept implementations to demonstrate how our framework is able to facilitate different types of interoperability. We believe that collaborative technologies such as mashups can implement process interoperability requirements to support collaborative care delivery, particularly for asynchronous care delivery.     

±800kV直流输电线路重冰区导、地线脱冰冲击敏感因素浅析.

结合±800 k V直流输电线路重冰区的实际工程数据,基于脱冰数值计算理论,通过数值方法模拟了六分裂导线在不同档数、档距、高差等复合因素影响下导线的脱冰动力响应过程,分析不同参数条件下导线和地线脱冰对悬垂绝缘子串和耐张绝缘串的冲击效应,得到最不利脱冰冲击效应的控制因素。研究表明:不同档距和高差组合下,档距和高差均最大时脱冰后的冲击效应最强;对于连续档,不同档脱冰时,对其相邻档导地线串的冲击效应最大;脱冰水平冲击效应主要受水平档距的影响,垂直冲击效应主要受高差的影响。     

HIGH TEMPERATURE OXIDATION AND STRUCTURE OF SCALE AND WHISKERS FOR Fe-Ni-Cr SEALING ALLOYS

The oxidation rate,the growth,morphology and structure of oxide scale and whiskers forFe-Ni-Cr sealing alloys in H_2-H_2O atmosphere at high temperatures have been studied.The growth rate of scale is controlled by diffusion.The scale is composed of Cr_2O_3 andspinel(Fe,Mn)O·Cr_2O_3 and the oxide whisker,are spinel(Fe,Mn)O·Cr_2O_3.