Effect of MoS2/PTFE coatings on performance of Si3N4/TiC ceramics in dry sliding against WC/Co

To enhance the tribological performance of Si₃N₄/TiC ceramics, MoS₂/PTFE composite coatings were deposited on the ceramic substrate through spraying method. The micrographs and basic properties of the MoS₂/PTFE coated samples were investigated. Dry sliding friction experiments against WC/Co ball were performed with the coated ceramics and traditional ones. These results showed that the composite coatings could significantly reduce the friction coefficient of ceramics, and protect the substrate from adhesion wear. The primary tribological mechanisms of the coated ceramics were abrasive wear, coating spalling and delamination, and the tribological property was transited from slight wear to serious wear with the increase of load because of the lower surface hardness and shear strength. The possible mechanisms for the effects of MoS₂/PTFE composite coatings on the friction performance of ceramics were discussed.     

Nanocrystallization and optical properties of CsPbBr3−xIx perovskites in chalcogenide glasses

The confinement of CsPbX₃ (X = Cl, Br, and I) perovskite nanocrystals (NCs) in a stabilized inorganic glass matrix is a new strategy for improving their long-term stability and promoting their applications in the optoelectronic field. Here, in situ nanocrystallization strategy is developed to precipitate CsPbBr_3?xI_x NCs with arbitrary I/Br ratio among an elaborately designed GeS₂–Sb₂S₃-based chalcogenide glass matrix. Spherical CsPbBr_3?xI_x NCs are homogeneously distributed in the glass matrix after thermal treatment. The photoluminescence (PL) spectra show that the emission peaks of CsPbBr_3?xI_x NCs can be tuned from 570 nm to 722 nm with the replacement of Br by I. The fs transient absorption (TA) spectra reveal that there exists some structural defects in the NCs, leading to short PL decay life. This work would shed light on confining CsPbX₃ NCs into glassy matrices, facilitating their future applications in photoelectronic fields.     

Synthesis of Light Hydrocarbons from Biogas and Hydrogen: Investigation of a Fe-Mn-K/MgO Catalyst

Fischer-Tropsch synthesis of the CO₂ in biogas aims at producing light hydrocarbons and increasing its calorific value for feeding into the grid. Fe catalysts with Mn and K as promoters are supposed to yield high amounts of light hydrocarbons. Using a Fe-Mn-K/MgO catalyst, a parameter screening and long-term experiments were carried out. The catalyst shows, within the examined range, the highest selectivity to C₂–C₄ hydrocarbons at 450 °C, 8 bar(a), and a gas hourly space velocity of 350 h⁻¹. Calcination of the catalyst resulted in a significant drop of activity and an almost complete loss of selectivity to hydrocarbons. Admixture of steam to the reactant gas lowers the tendency to carbon deposition but also promotes the water-gas shift reaction and results in lower yields of hydrocarbons.     

Blocked crystallization in capped ultrathin polymer films studied by molecular simulations

The crystallization of capped ultrathin polymer films is closely dependent on film thickness and interfacial interaction. Using dynamic Monte Carlo simulations, the crystallization behaviors of polymer films confined between two substrates were investigated. The crystallization rate of confined polymers is reduced with high interfacial interactions. Above a critical strength of interfacial interaction, polymer crystallization in the thin film is inhibited within the simulation time scales. An increase in film thickness leads to a rise in critical interfacial interaction. In thicker films, the chains have more space to change conformation to form crystal stems. In addition, there are fewer absorbed segments in confined chains for the thicker films, and thus the chains have stronger ability to adjust their conformation. Therefore an increase in film thickness can cause a reduction in the entropic barrier required for the formation of crystals and thus an increase in the critical interfacial interaction. © 2018 Society of Chemical Industry     

Polyethylene oxide-polypropylene oxide -polyethylene oxide derived porous carbon materials with different molecular weights as ORR catalyst in alkaline electrolytes

Polyethylene oxide (PEO)-polypropylene oxide (PPO)-polyethylene oxide block copolymer having different molecular weights are used as precursors of carbon materials to prepare Hollow -Derivatives carbon material as an electrocatalyst through block copolymer self-assembly. The composition and microstructure of the prepared catalysts are shown by Raman spectroscopy, X-ray diffraction (XRD), Test of nitrogen adsorption and desorption curves, High resolution transmission electron microscopy (HR-TEM) and scanning electron microscopy (HR-SEM). Oxygen was passed into alkaline electrolyte solution until the solution reached saturation state. With molecular weight increasing, the obtained sample gradually changed from block to hollow and spherical. When the molecular weight was 12600 g mol^?1, the evenly hollow carbon nanocages was acquired (C-12600). In O₂ saturated alkaline electrolyte (0.1 M KOH solution), C-12600's limited current density，half-wave potential and initial potential are 5.23 mA cm^?2@0.4 V, 0.72 V and 0.81 V, respectively. And most important is that half-wave potential and onset potential have barely change after 2000 cycles of cyclic voltammetry. As a result, the porous carbon materials exhibited excellent electrocatalytic activity while maintaining high stability in alkaline KOH solution.     

燃煤锅炉除尘专用滤料的开发

介绍机械制造厂燃煤锅炉的烟尘特点,分析滤料失效的原因,提出一套针对该工况的滤料解决方案。介绍针对复杂工况条件所选用的纤维种类以及复合面层原料成分配比的确定,最终选用针刺工艺加工并对该新产品的基本性能进行了测试分析。