Stabilization of bioethanol recovery with silicone rubber‐coated ethanol‐permselective silicalite membranes by controlling the pH of acidic feed solution

In order to produce highly concentrated bioethanol by pervaporation using an ethanol‐permselective silicalite membrane, techniques to suppress adsorption of succinic acid, which is a chief by‐product of ethanol fermentation and causes the deterioration in pervaporation performance, onto the silicalite crystals was investigated. The amount adsorbed increased as the pH of the aqueous succinic acid solution decreased. The pervaporation performance also decreased with decreasing pH when the ternary mixtures of ethanol/water/succinic acid were separated. Using silicalite membranes individually coated with two types of silicone rubber, pervaporation performance was significantly improved in the pH range of 5 to 7, when compared with that of non‐coated silicalite membranes in ternary mixtures of ethanol/water/succinic acid. Moreover, when using a silicalite membrane double‐coated with the two types of silicone rubber, pervaporation performance was stabilized at lower pH values. In the separation of bioethanol by pervaporation using the double‐coated silicalite membrane, removal of accumulated substances having an ultraviolet absorption maximum at approximately 260 nm from the fermentation broth proved to be vital for efficient pervaporation. Copyright © 2005 Society of Chemical Industry     

Temperature and pressure effects on supercritical CO2 extraction of tomato seed oil

Tomato seed oil was extracted with supercritical carbon dioxide in a semibatch-flow extractor within the temperature range 313–343 K and the pressure range 10.8–24.5MPa. The extraction rates increased with pressure, but decreased with temperature increase because of the variation in solvent density and resultant differences in oil solubility. The fatty acid composition of the extracted oil was similar to that of soybean oil.     

Numerical analyses of high‐beta spherical tokamaks with varied elongation

The effect of plasma elongation on the second‐stable spherical tokamak (ST) was numerically studied using the experimentally measured pressure and current profiles of ultrahigh‐beta STs. The maximum beta of ST over 50% was obtained in the TS‐3 ST/CT experiment by applying an external toroidal field to an FRC. It was found that the marginal beta for the ballooning instability increased with the plasma elongation κ of ST. The elongated STs with κ > 2 have the magnetic shear (S)–pressure gradient (α) profiles located in the second‐stable regime for the ballooning mode and the stability margin increased with κ. The close relation between the absolute minimum‐B profile and the second stability was documented. The effect of elongation on maximum beta was observed to saturate when κ exceed 3, indicating that the optimized elongation for high‐beta STs is located around 2 < κ < 3. © 2006 Wiley Periodicals, Inc. Electr Eng Jpn, 155(4): 1–6, 2006; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20132     

Multiobjective dynamic load-dispatching method for optimal operation of power systems

A new practical method is proposed which gives a quasi-optimal solution of the dynamic load-dispatching problem formulated by a multiconstraint multiobjective optimization problem. Here, the multiple constraints are rate reserve constraints and power flow ones, and the multiple objectives are fuel cost and CO₂ emission. The proposed method is an integration of the following three techniques: (1) “Group Dispatch Scheme,” which is developed by the authors, is used to satisfy a violated constraint easily. This scheme consists of three steps. The first step is to classify all generators into two groups. One is the group which should be more loaded to satisfy the violated constraint, and the other is the should-be less loaded group. The second step is to add some load to the former group, and to subtract the same load from the latter. The third step is to dispatch each group load to each groups generators, respectively; (2) the dynamic load-dispatching algorithm is used which provides, in practical time, quasi-optimal generation trajectories; (3) the conventional weighting parametric method is used to obtain a Pareto optimal solution of multiobjective problems. The effectiveness of the method is clarified by a computer simulation on the actual power system of Kansai Electric Power Company.     

Flexural properties of moldings of rigid polyurethane made by reaction injection molding

Flexural properties of moldings made by Reaction Injection Molding (RIM), which are structural foams consisting of high density skin and low density core, were investigated by three-point bending tests. Two failure modes were observed in bending tests of the moldings made by RIM, and they are classified as follows according to the density ratio of skin layer to core layer: the opposite side of the skin layer to which load was subjected failed by tensile stress: and the same side of the skin layer to which load was subjected failed by compressive stress, causing wrinkling or buckling. Then the conventional composite beam theory was applied to the former failure mode and Hoff s buckling theory to the latter, and equations were derived to predict the flexural properties of the structural foams, which involved buckling from the flexural properties of solid construction. In addition, it has been shown that there exists a density distribution that maximizes the flexural strength of the moldings made by RIM with a given overall density. The results obtained here should be useful to the optimum structural design of moldings made by RIM.     

Antioxidant effects of chlorophyll and pheophytin on the autoxidation of oils in the dark. I. Comparison of the inhibitory effects

The effects of chlorophyll and pheophytin on the autoxidation of oils in the dark were investigated by oven tests. The results indicated that both chlorophyll and pheophytin show antioxidant activity when methyl linoleate is used as substrate. Furthermore, chlorophyll retarded the oxidative deterioration of triglycerides in rapeseed and soybean oils at 30 C. Among the four chlorophyll derivatives (chlorophylls a and b and pheophytins a and b), chlorophyll a showed the strongest antioxidant activity. The antioxidant effects of chlorophyll and pheophytin depended on the storage temperature and the kinds of oil used as substrate.     

Preparation of Aluminum Nitride Powder from Aluminum Polynuclear Complexes

AIN powder was synthesized from aluminum polynuclear complexes. Basic aluminum chloride and basic aluminum lactate were used as the aluminum polynuclear complexes. These starting materials and glucose were dissolved in water and mixed homogeneously. AIN powder was obtained by calcining after drying and precalcining at 800°C under nitrogen gas flow. Then excess carbon was removed by firing in air. Nitridation in the system was investigated and compared with that in the alumina–carbon black system. It was found that in our reaction system nitridation began and proceeded at lower calcination temperatures above 1200°C than in the alumina–carbon black system. Using aluminum polynuclear complexes, AIN was synthesized through the nitridation of γ-alumina and produced in a very fine and sharp particle size distribution.     

The structure of acetylene flames for diamond synthesis

An acetylene flame was photographed with an SIT camera through optical filters, and the signals were Abel transformed to obtain two-dimensional emission-intensity profiles. It was found that the intensive emissions of CH* and C*₂ are localized at the feather boundary, while the OH* emission is localized at the intermediate zone. The structure of the acetylene flame was made clear: it consists of a carbon-radical-rich feather and an oxygen-radical-rich intermediate zone. The carbon-radical concentrations are approximately in equilibrium near the burner exit while they decrease almost linearly via interdiffusion and reactions with the oxygen-radicals in the intermediate zone.Numerical simulations including detailed gaseous and surface reactions reproduced well previous preliminary calculations showing that CH₄ is rapidly produced in the boundary layer near the substrate followed by an increase in CH₃. This result satisfactorily explains the measured dependence of growth rate on the substrate temperature and ratio.     

Hydrothermal Formation of Hydroxyapatite Layers on the Surface of Type-A Zeolite

Type-A zeolite evenly covered with hydroxyapatite thin layers was prepared using hydrothermal treatment at 120°C for 8 h under autogenous pressure. The hydroxyapatite needlelike nanocrystals, 100–200 nm in diameter and 30 nm in thickness, were grown under the reaction between discharged Ca²⁺ ions from type-A zeolite and PO₄³⁻ ions in (NH₄)₃PO₄ solution. The preferential orientations of the c -axis of hydroxyapatite crystals perpendicular to a zeolite surface were observed using transmission electron microscopy. The crystal structure of type-A zeolite was not destroyed under the reaction, but the surface morphology was changed only with complete covering of scaly hydroxyapatite particles.