Operation of superconducting fault current limiter using vacuum interrupter driven by electromagnetic repulsion force for commutating switch

Using conventional high‐temperature superconducting wire, a model superconducting fault current limiter (SFCL) is made and tested. Solenoid coil using Bi2223 silver sheath wire is so made that inductance is as small as possible and a vacuum interrupter is connected in series to it. A conventional reactor coil is connected in parallel. When the fault current flows in this equipment, superconducting wire is quenched and current is transferred into the parallel coil because of voltage drop of superconducting wire. This large current in parallel coil actuates magnetic repulsion mechanism of vacuum interrupter. Due to opening of vacuum interrupter, the current in superconducting wire is broken. By using this equipment, current flow time in superconducting wire can be easily minimized. On the other hand, the fault current is also easily limited by large reactance of parallel coil. © 2008 Wiley Periodicals, Inc. Electr Eng Jpn, 164(1): 52–61, 2008; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20315     

Use of a YAP1 overexpression cassette conferring specific resistance to cerulenin and cycloheximide as an efficient selectable marker in the yeast Saccharomyces cerevisiae.

Drug-resistance markers for yeast transformation are useful because they can be applied to strains without auxotrophic mutations. However, they are susceptible to technical difficulties, namely lower transformation efficiency and the appearance of drug-resistant mutants without the marker. To avoid these problems, we have constructed a phosphoglycerate kinase (PGK) promoter-driven YAP1 expression cassette, called PGKp-YAP1. Yeast cells containing PGKp-YAP1 were resistant to cycloheximide, a protein synthesis inhibitor, and also to cerulenin, a fatty acid synthesis inhibitor, but not to other drugs tested. The transformation efficiency of PGKp-YAP1 using cerulenin selection was comparable to that using a URA3 auxotrophic marker when low concentrations of cerulenin were used. Non-transformed drug-resistant colonies did appear on the low-concentration cerulenin plates. However, these non-transformed colonies could easily be identified, based on their cycloheximide sensitivity and/or their resistance to aureobasidin A to which the transformants were sensitive. Therefore, the dual drug resistance of PGKp-YAP1 could be used as an effective selection for PGKp-YAP1 recipient cells. The PGKp-YAP1 marker was used to disrupt the LYS2 gene and to transform an industrial yeast strain, indicating that this marker can be used for efficient and reliable gene manipulations in any Saccharomyces cerevisiae strain.     

Adaptive control-based high-performance drive system implementation of traveling-wave-type ultrasonic motor

In recent years, ultrasonic motors (USM) as new actuators have attracted special interest. Several kinds of constructions and characteristics of USMs have been reported so far. Of these USMs, a traveling wave-type USM has many characteristics such as: high torque in the low-speed range, large holding torque based upon frictional force, flexible free forms, compactness in size and low magnetic noise. In practice, an inherent mechanical resonant frequency and a velocity amplitude of USM are changed largely according to operating temperature due to frictional drive, load disturbance torque, and applied voltage levels. Therefore, it is necessary to develop a new control system which solves these items and always supplies the required power with high efficiency and high performance in the practical applications. This paper proposes mainly a new sensorless high-performance control scheme of an inverter-fed ultrasonic motor, which is based on a control system technology with two feedbacks incorporating automatic resonant frequency tracking and constant velocity amplitude control strategies. This control system is realized in terms of a high-frequency chopper and a two-phase series/parallel resonant inverter. The experimental results are demonstrated and discussed compared with the theoretical ones.     

Optical data storage by novel photoelectrochromic polymer

A novel elastic polymer containing 4,4′-bipyridinium salts with tetrakis[3,5-bis(trifluoromethyl)phenyl]borate as part of the main chain was synthesized. The cast film showed persistent and reversible colour changes due to photoinduced electron transfer upon excitation of an ion-pair charge-transfer band (_ex >365 nm) in vacuo. The lifetime of the coloured state markedly depended on temperature. The optically written data were stored without decay below 0°C and were erased thermally at elevated temperatures. The colour changes were reversibly repeatable for many times.     

An investigation of induced voltages to an underground gas pipeline from an overhead transmission line

This paper investigates induced voltage characteristics from an overhead transmission line by applying a method of modeling of induced voltages proposed by the authors. EMTP simulation results obtained by the modeling method agree with analytical results obtained from a well‐known formula. The induced voltages are significantly dependent on the configuration of the overhead line. A horizontal line induces the largest voltage in a gas pipeline, and the voltage induced by a vertical twin‐circuit line is about 20% smaller than that induced by a vertical single‐circuit line. The method is applied to a real pipeline system and the simulation results show reasonable agreement with field test results. © 2008 Wiley Periodicals, Inc. Electr Eng Jpn, 164(1): 43–51, 2008; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20465     

Multiobjective dynamic load-dispatching method for optimal operation of power systems

A new practical method is proposed which gives a quasi-optimal solution of the dynamic load-dispatching problem formulated by a multiconstraint multiobjective optimization problem. Here, the multiple constraints are rate reserve constraints and power flow ones, and the multiple objectives are fuel cost and CO₂ emission. The proposed method is an integration of the following three techniques: (1) “Group Dispatch Scheme,” which is developed by the authors, is used to satisfy a violated constraint easily. This scheme consists of three steps. The first step is to classify all generators into two groups. One is the group which should be more loaded to satisfy the violated constraint, and the other is the should-be less loaded group. The second step is to add some load to the former group, and to subtract the same load from the latter. The third step is to dispatch each group load to each groups generators, respectively; (2) the dynamic load-dispatching algorithm is used which provides, in practical time, quasi-optimal generation trajectories; (3) the conventional weighting parametric method is used to obtain a Pareto optimal solution of multiobjective problems. The effectiveness of the method is clarified by a computer simulation on the actual power system of Kansai Electric Power Company.     

Identification of osteopontin in human dental calculus matrix

Osteopontin is a prominent non-collagenous component of bone matrix, although it is expressed in several other tissues. Recently, osteopontin was reported to be involved in urinary stone formation and atherosclerotic lesions of the aorta, suggesting that it may be a key protein associated with these types of pathological mineralization. In this study, whether or not human dental calculus contains osteopontin was investigated by immunoblotting and immunohistochemical analyses. After extraction of calculus proteins with EDTA and separation of the proteins by electrophoresis, immunoblotting analysis revealed the presence of osteopontin. Two forms of osteopontin appeared at 61 and 68 kDa on 10% polyacrylamide gel and the proteins were digested with thrombin, a highly specific protease. Moreover, immunohistochemical analysis revealed that osteopontin was localized in dental calculus adherent to tooth roots. These findings indicate that osteopontin is, in fact, present in human dental calculus and may be involved in calculus formation as the stone matrix.     

高速气流冲击式粉体表面改性装置——HYBRIDIZATION系统及应用

利用高速气流冲击法进行粉体/粉体系表面改性技术,是迄今为止各种粉体材料开发中最为引人注目的技术之一。HYBRIDIZATION(下称HYB)系统是利用高速气流冲击法对微粉体进行干式/机械化处理,是使材料复合化的最实用的装置,可对各类有机物、无机物、金属等进行广泛组合,通用性很强,适用于许多行业领域。从本文所述的系统构成、型式,有关的典型球形化处理的运转特性,利用复合化高温粉体测定被处理粉体表面温度,利用颜料改变色调等的处理特点及该系统的适用性等(一部分是从已发表的学术论文及专利上摘录的),可以说明HYB系统的概况。     

The reaction of polypropylene with maleic anhydride

An addition reaction of maleic anhydride with polypropylene takes place in the presence of radical reagents or sunlight. The initial rate of the reaction was proportional to the concentration of polypropylene and maleic anhydride, and one-half power of the concentration of the radical reagents. The increase in the temperature from 80 to 120°C increased the rate of the reaction and di-cumyl peroxide was effective as a radical reagent for this reaction. Ionic crosslinked rubber-like polymers were obtained from the reaction of maleic polypropylene with some alkali metal compounds. They showed the characteristic absorption band due to ? COO^? in their infrared spectra.     

Deuterium trapping by irradiation damage in tungsten induced by different displacement processes

The deuterium trapping behaviors in tungsten damaged by light ions with lower energy (10 keV C⁺ and 3 keV He⁺) or a heavy ion with higher energy (2.8 MeV Fe²⁺) were compared by means of TDS to understand the effects of cascade collisions on deuterium retention in tungsten. By light ion irradiation, most of deuterium was trapped by vacancies, whose retention was almost saturated at the damage level of 0.2 dpa. For the heavy ion irradiation, the deuterium trapping by voids was found, indicating that cascade collisions by the heavy ion irradiation would create the voids in tungsten. Most of deuterium trapped by the voids was desorbed in higher temperature region compared to that trapped by vacancies. It was also found that deuterium could accumulate in the voids, resulting in the formation of blisters in tungsten.