Eco-friendly and degradable red phosphorus nanoparticles for rapid microbial sterilization under visible light

Pathogens pose a serious challenge to environmental sanitation and a threat to public health.The frequent use of chemicals for sterilization in recent years has not only caused secondary damage to the environment but also increased pathogen resistance to drugs,which further threatens public health.To address this issue,the use of non-chemical antibacterial means has become a new trend for environmental disinfection.In this study,we developed red phosphorus nanoparticles(RPNPs),a safe and degradable photosensitive material with good photocatalytic and photothermal properties.The red phosphorus nanoparticles were prepared using a template method and ultrasonication.Under the irradiation of simulated sunlight for 20 min,the RPNPs exhibited an efficiency of 99.98%in killing Staphylococcus aureus due to their excellent photocatalytic and photothermal abilities.Transmission electron microscopy and ultraviolet–visible spectroscopy revealed that the RPNPs exhibited degradability within eight weeks.Both the RPNPs and their degradation products were nontoxic to fibroblast cells.Therefore,such RPNPs are expected to be used as a new type of low-cost,efficient,degradable,biocompatible,and eco-friendly photosensitive material for environmental disinfection.     

Effects of Cooling Rate and Component on the Microstructure and Mechanical Properties of Mg–Zn–Y Alloys

The microstructure and mechanical properties of Mg–6Zn–1Y and Mg–6Zn–3Y(wt%) alloys under different cooling rates were investigated. The results show that the second dendrite arm spacing(SDAS) of Mg–6Zn–1Y and Mg–6Zn–3Y is reduced by 32 and 30% with increasing cooling rates(Rc) from 10.2 to 23 K/s, which can be predicted using a empirical model of SDAS=68 R 0:45:45cand SDAS=73 R 0c, respectively. The compressive strength of both alloys increases with increasing the cooling rate, which is attributed to the increase of volume fraction(Vf) of secondary phases under high cooling rate. The interaction of the cooling rate and component with SDAS has been theoretically analyzed using interdependence theory.     

Study on the Complexity of the Bullwhip Effect

Recent years have witnessed a rapid growth of interest in the study of the dynamic behavior of replenishment rules of bullwhip effect. We prove that bullwhip effect and butterfly effect share a same the self-oscillation amplifying mechanism that is the ordering decisions the supplier self-oscillation amplify the perturbations brought by the errors in the processing of retailers' demand information. This results as an explicit self-similar structure of the sensitivity of the system to the initial values duty to the nonlinear mechanism. In this paper, the causes process of the bullwhip effect is described as the internal nonlinear mechanism and study on the complexity of bullwhip effect for order-up-to policy under demand signal processing. The methodology is based on fractal and chaotic theory and allows important insights to be gained about the complexity behavior of bullwhip effect.     

变频节能技术及其应用

介绍了风机水泵的变频节能技术 ,并通过实例 ,阐述了先进变频系统ACS60 0在风机控制应用中的显著效果以及所带来的巨大的经济效益。     

用于实时数据传输的滑动帧方法及其实现

根据某雷达系统对测量信号的快速传输要求,提出采用滑动帧的处理方法并在FPGA中实现,克服了传统帧处理难以满足快速传输要求的不足。阐述了滑动帧结构的构造思想,详述了滑动帧结构的特点及具体功能模块的实现。根据实际应用需求构造了滑动帧结构处理器,试验和应用结果表明设计可行有效,能充分满足实时数据传输的要求。     

渐开线齿轮交错轴无侧隙方程

本文给出了无侧隙方程的两种形式,加上原来的,共三种表达形式;并定义了无侧隙方程中齿厚元素M的三种参数形式,以适用于不同的参数条件。本文还指出:无侧隙啮合的两齿轮“节圆法向齿厚之和等于节圆法向齿距”应该是有条件的。 (一)近年来,渐开线齿轮(及其刀具)交错轴啮合应用研究涉及到了非规则状态,导致对非规则啮合无侧隙方程认识逐步深化。早在1959年文献以媒介齿条为工具建立了渐开线齿轮交错轴无侧隙方程(符号按原文):     

Modeling resonator frequency fluctuations induced by adsorbing and desorbing surface molecules

Resonator frequency fluctuations due to adsorption and desorption of molecules on plate electrodes are studied using the principle of mass-loading effects of adsorbed molecules. The study is based on a 525 MHz, AT-cut quartz resonator enclosed in a small crystal holder. Equations relating the surface adsorption rates of the crystal holder to pressure were derived and found to be quadratic polynomial functions of the adsorption rates. Calculations based on these equations show that a contaminant gas with a higher desorption energy creates larger changes in pressure when the temperature is varied. The function describing the frequency fluctuations due to any one contaminant site is a continuous-time Markov chain. Kolmogorov equations and an autocorrelation function for the Markov chain are derived. The autocorrelation and spectral density function of resonator frequency fluctuations are derived. The spectral density of frequency fluctuations at 1 Hz is studied as a function of pressure, temperature, and desorption energy of molecules. The noise levels for a contaminant gas with one type of molecules are found to be lower for lower desorption energies, and higher at lower pressures.     

Resonator surface contamination-a cause of frequency fluctuations?

The mass loading effects of adsorbing and desorbing contaminant molecules on the magnitude and characteristics of frequency fluctuations in a thickness-shear resonator are studied. The study is motivated by the observation that the frequency of a thickness-shear resonator is determined predominantly by such mechanical parameters as the thickness of the resonator, elastic stiffnesses, mass loading of the electrodes, and energy trapping. An equation was derived relating the spectral density of frequency fluctuations to: (1) rates of adsorption and desorption of one species of contaminant molecules; (2) mass per unit area of a monolayer of molecules: (3) frequency constant; (4) thickness of resonator; and (5) number of molecular sites on one resonator surface. The induced phase noises were found to be significant in very-high-frequency resonators and are not simple functions of the percentage of area contaminated. The spectral density of frequency fluctuations was inversely proportional to the fourth power of the thickness if other parameters were held constant.     

ON THE COMPOSITION UNIFORMITY AND SHAPE COEFFICIENT OF MOLTEN POOL BY LASER ALLOYING

The effect of the laser processing parameters on the composition uniformity and shapecoefficient of fusion zone with laser surface alloyed Cr plated on medium carbon low alloysteel has been studied.It was found that the composition uniformity depends on the shapecoefficient of fusion zone,and the later is a function of both power density and interactiontime.If the power density is fixed to a certain value,the shape coefficient is directly,propor-tional to the interaction time.A completely,uniform molten pool can be obtained,when theshape coefficient is between 1.6 and 3.0.