Analysis and design of broadband U-slot cut rectangular microstrip antennas

Broadband microstrip antenna using variations of U-slot has been widely reported. However, in most of the reported work, an in-depth explanation about the mode introduced by U-slot and procedure to design U-slot cut antennas at any given frequency is not explained. In this paper, first an extensive analysis to study the broadband response in symmetrical and a new configuration of asymmetrical U-slot cut rectangular microstrip antennas is presented. The U-slot tunes higher-order orthogonal mode resonance frequency of the patch with respect to fundamental mode to realise wider bandwidth. Further formulation in resonant length at modified patch modes in symmetrical U-slot cut antenna is proposed. Frequencies calculated using these formulations show closer agreement with simulated and measured results. Using proposed formulations, a procedure to design U-slot cut antenna at different frequencies over 800–4000 MHz range which shows broadband response is explained. Thus, the proposed work gives an insight into the functioning of widely used U-slot cut antennas and the formulations will be helpful for designing at any given frequency.     

CONSTRUCTION AND OPERATIONAL EXPERIENCE OF A 6000 m SOLAR POND AT KUTCH, INDIA

A 6000 m² solar pond was constructed at Bhuj in India in the premises of a milk processing dairy plant to supply process heat and demonstrate the technical and economic viability of solar pond technology in the Indian context. An inexpensive lining scheme, consisting of alternating layers of clay and LDPE (low density polyethylene) combination was used for lining the pond. The pond attained a maximum temperature of 99.8°C under stagnation in May 1991 but developed leakage soon after. A failure analysis that was carried out subsequently indicated that the leakage was caused by the combination of high stagnation temperature and large air pockets below the liner. The lining scheme was re-designed and the pond re-established in June 1993. Hot water supply to the dairy started in September 1993 and continued until April 1995. After an interruption of nearly one year, hot water was resumed in August 1996. The total cost of construction of the Bhuj Solar Pond was US$90 000 (1997 prices), including heat exchanger and piping etc., corresponding to a unit cost of US$15 m⁻².     

On postponement strategies for product families with multiple points of differentiation

Several researchers have studied the benefits of product and process design that calls for delaying the differentiation of products. Previous research has focused on products having only one point of differentiation. However, in reality most product families have several points of differentiation. In this paper, we develop two models to study products with more than one point of differentiation. In each model, we examine the benefits of delayed differentiation at each of these points, and derive the necessary conditions when one type of delayed differentiation is more beneficial than the other. Our analysis indicates that demand variabilities, correlations and the relative magnitudes of the lead times play an important role in determining which point of differentiation should be delayed.     

A method for unbalanced transportation problems in fuzzy environment

In this paper, we consider the fully fuzzy unbalanced transportation problem in which the total availability/production is more than the total demand and propose a method to solve it. Such problems are usually solved by adding a dummy destination. Since the dummy destination has no existence in reality, the excess availability is not transported at all and is held back at one or more origins. The method proposed in this paper gives the additional information that to which of the destination(s) the excess availability be transported for future demand at minimum cost. The advantage of the proposed method over the existing method is that the fuzzy optimal solution obtained does not involve the dummy destination. The method has been illustrated with the help of an example.     

Ultraviolet sensing properties of polyvinyl alcohol-coated aluminium-doped zinc oxide nanorods

Undoped and aluminium (Al)-doped zinc oxide (ZnO) nanorods have been synthesized by electrochemical route. The synthesized materials have been characterized by X-ray diffraction, UV–visible spectrometer and scanning electron microscope. The Al-doped ZnO nanorods have been coated with polyvinyl alcohol. Current–voltage characteristics have been investigated in dark and under UV-light illumination. Aluminium doping in ZnO increase its electrical conductivity and further polyvinyl alcohol coating on Al-doped ZnO increase UV sensitivity of the material. Response and recovery time of Al-doped ZnO and PVA-coated Al-doped ZnO nanorods have been recorded. PVA-coated Al-doped ZnO nanorods shows very fast response and recovery time of 10 s in comparison to uncoated ZnO (20 min) nanorods.     

Optimization of processing parameters in induction hardening using response surface methodology

In this paper, an effective procedure of response surface methodology (RSM) has been utilized for finding the optimal values of process parameters while induction hardening of AISI 1040 under two different conditions of the material i.e., rolled and normalized. Various process parameters, such as feed rate (speed at which the induction coil moves, which is measured in mm/sec), current, dwell time (time after which heat intensity starts to heat work piece in seconds) and gap between the work piece and induction coil have been explored by experiments. Hardness at two different conditions has been considered as performance characteristic. The experiment plan was based on rotatable, central composite design (CCD). The experimental results showed that the proposed mathematical models suggested could describe the performance indicators within the limits of the factors being investigated. The obtained optimal process parameters have been predicted and verified by confirmation experiments. Microstructure and SEM (scanning electron microscope) analyses were also done for justification of the work.     

Sol-Gel Synthesis of Magnesium Oxide-Silicon Dioxide Glass Compositions

MgO-SiO₂ glasses containing up to 15 mol% MgO, which could not have been prepared by the conventional glass-melting method because of the presence of stable liquid-liquid immiscibility, have been synthesized by the sol-gel technique. The gelling time decreased with increase in magnesium content, water: TEOS ratio, and reaction temperature. The gels were subjected to various thermal treatments and characterized using DTA, TGA, IR spectroscopy, XRD, and surfacearea- and port-size-distribution measurements. No organic groups could be detected in the glasses after heat treatments to ∼800°C, but trace amounts of hydroxyl groups were still present. The overall activation energy for gel formation in the 10MgO·90SiO₂ (mol%) system for the water: TEOS mole ratio of 7.5 was calculated to be 58.7 kJ/mol.     

Heat Extraction from a Diffusely Reflecting Bottom Salt Gradient Solar Pond

This paper presents an investigation of a three zone solar pond with a diffusely reflecting bottom under two modes of heat extraction viz. constant flow rate of the heat removal fluid and heat retrieval zone at constant temperature. At a typical flow rate of 10^-3 kg/s m ² M. S. Sodha , N. D. Kaushika and S. K. Rao , Energy Research , 5 , 321 – 340 , 1981 . [Google Scholar], optimal heat retrieval efficiencies of 32.4% (at non-convective zone depth, l_-2 = 1.25m), 25.2% (at l_-2 = 0.75m) and 21.5% (at l_-2 = 0.6m) are predicted at bottom reflectivities of 0.0, 0.5 and 0.8 respectively. In the mode of heat retrieval at constant temperature, efficiencies of 32.5% and 23.5% are obtained at extraction temperatures of 40°C and 100°C respectively for R = 0.0. However, these values of efficiency go down to 22.3% and 12.4% respectively for a typical value of R = 0.6.     

ESTIMATION OF MOISTURE LOSS FROM THE COOLING DATA OF POTATOES

A procedure was developed to predict moisture loss from cooling data of potato packed in gunny bags and stacked on wooden platforms in commercial cold stores. To predict the moisture loss, mass transfer coefficients k_cand k_mwere estimated during the storage period, which were found to decrease with time. The calculated time average k_cand k_mvalues were 1.83 × 10^?4 m/s and 2.31 × 10^?10 kg/s·m²·Pa during the transient cooling period and 1.59 × 10^?4 m/s and 2.27 × 10^?10 kg/s·m²·Pa for the rest of the storage period, respectively. The estimated moisture losses were 4.8, 4.74 and 4.78%, at the center of three different stacks, for a storage period of 8 months. The corresponding experimentally measured weight losses at the center of the same stacks were 5.2, 5.1 and 5.26% with a variation of 11, 7.5 and 10.2%, respectively. Therefore, the procedure adopted in this study may be used to assess the moisture loss from potatoes under the different storage conditions. The effect of relative humidity (RH) and potato temperature on moisture loss was also predicted using the developed procedure. Decrease in RH of the storage air increased the moisture loss. The potatoes stored below 85% RH incurred more than 7% water loss. Therefore, 88–90% RH in the cold store may be used to limit the maximum moisture loss within the permissible limit of 5% even after 8 months of storage. It was also found that increasing the potato temperature exponentially increased the rate of moisture loss.