Internal electrical fault detection techniques in DFIG-based wind turbines: a review

The keys factor in making wind power one of the main power sources to meet the world’s growing energy demands is the reliability improvement of wind turbines (WTs). However, the eventuality of fault occurrence on WT com ponents cannot be avoided, especially for doubly-fed induction generator (DFIG) based WTs, which are operating in severe environments. The maintenance need increases due to unexpected faults, which in turn leads to higher operating cost and poor reliability. Extensive investigation into DFIG internal fault detection techniques has been carried out in the last decade. This paper presents a detailed review of these techniques. It discusses the methods that can be used to detect internal electrical faults in a DFIG stator, rotor, or both. A novel sorting technique is presented which takes into consideration different parameters such as fault location, detection technique, and DFIG modelling. The main mathematical representation used to detect these faults is presented to allow an easier and faster under standing of each method. In addition, a comparison is carried out in every section to illustrate the main differences, advantages, and disadvantages of every method and/or model. Some real monitoring systems available in the market are presented. Finally, recommendations for the challenges, future work, and main gaps in the field of internal faults in a DFIG are presented. This review is organized in a tutorial manner, to be an effective guide for future research for enhancing the reliability of DFIG-based WTs.     

The role of electrolyte concentration on crevice corrosion of pure nickel

In this work an artificial crevice electrode was used in conjunction with a fine microprobe assembly to measure the potential inside the crevice. Using this setup crevice corrosion of commercially pure nickel was investigated in sulfuric acid with concentrations: 0.5, 1 and 2N. The outer surface of the Ni was held at a passive potential of 530 mV(SCE) while the experiment was running. The results showed a steep potential decay observed in all concentrations. For 0.5, 1 and 2N H₂SO₄, the total potential drop inside the crevice was: 681, 619 and 593 mV, respectively. This indicates the higher the acid concentration is the lower the potential drop will be. On the other hand, the measured current was highest (4.09 mA) for 2N and lowest (1 mA) for 0.5N. On the crevice wall a boundary was found to exist between the passive and the active regions. These findings point toward the IR voltage drop mechanism operating for this system.     

Insight into kinetics and thermodynamics properties of multicomponent lead(II), cadmium(II) and manganese(II) adsorption onto Dijah-Monkin bentonite clay

Multicomponent adsorption of lead(II), cadmium(II) and manganese(II) by Nigerian Dijah-Monkin bentonite clay was investigated. The clay samples were characterized for elemental composition, cation exchange capacity and textural properties. Natural bentonite exhibits cation exchange capacity of 47.7?meq/100?g and specific surface area of 23.5?m²/g. Manganese(II) displays higher values of rate constant than lead(II) in multimetals adsorption. However, lead(II) is favorably adsorbed onto bentonite adsorbents at different concentrations studied. The multimetals adsorption onto bentonite clay samples is site selective and site specific. The pseudo-second-order kinetics model gave a better fit to the adsorption data, suggesting ion exchange and/or complex formation. The adsorption mechanism could be described by intraparticle diffusion with some restriction of metals diffusion due to film or boundary layer. Also, the multicomponent adsorption is endothermic and becomes more spontaneous as temperature increased from 303 to 338?K. Nigerian bentonite clay in its natural form is a promising adsorbent for multimetals removal in aqueous solution.     

An integrated technique using solar and evaporation ponds for effective brine disposal management

Desalination is a process that involves the removal of salts and non-ionic minerals from seawater to produce freshwater that is fit for human consumption. This process produces brine, which is typically redisposed into the sea. The relatively high salt concentration in the disposed brine increases the salinity of water and soil, which adversely affects the environment. However, brine is found to be rich in economically valuable minerals. In order to effectively manage the disposed brine, this study proposes an integrated technique using solar and evaporation ponds to filter valuable minerals from concentrated brine. The results of this study demonstrate that the proposed technique can be effectively employed for this purpose. Furthermore, this helps reduce desalination costs and complies with the notion of renewable energy production and eco-friendliness.     

Radiation modelling and performance evaluations of fixed,single- and double-axis tracking surfaces: a case study for Dhahran city,Saudi Arabia

This work overviews the solar radiation basics and insolation of different surfaces is presented. A complete solar radiation modelling and investigation on the effect of horizontal plate, yearly tilt, monthly tilt, and single-axis and double-axis tracking surface on the insolation are carried out to conduct performance evaluation using the case study in Dhahran city of Saudi Arabia. The increments received by insolation for the yearly tilt, monthly tilt, and single-axis and dual-axis tracking surface with respect to traditional flat-plate collector is estimated. The results show that the yearly optimal tilt angle due to the south is close to the 0.913 time latitude of Dhahran. It is found that the yearly irradiation gains using yearly and monthly optimal tilts relative to flat panel installation are 7% and 14%, respectively. The yearly insulation gains made by single-axis and dual-axis continuous tracking surfaces are 33% and 48%, respectively.     

ANALYSIS OF USED OIL BY IR-SFECTROSCOPIC AND SYNTHESIS OF DISPERSIONS OF A HIGHLY BASIC PETROLEUM CALCIUM SULFONATE ADDITIVE

ABSTRACT

Infrared absorptions of TLC subtractions of used motor oil, original oil, base oil and the additive, indicate the transformation of the polar and nonpolar components by further oxidation and oxidative degradation of carbonyl compounds into acids, esters and peroxides. Organic nitrates and nitro compounds were also detected after 2000Km and 3000Km service. The effects of basic calcium sulfonate additives, starting with used oil l000Km, 2000Km, 3000Km service, vacuum distillates of used oils and base oil, were studied. It has been found that the dispersant properties of these sulfonates are profoundly influenced by their structure. The alkalinity of the calcium sulfonate additive was determined by spectroscopic-IR method.     

Internal electrical fault detection techniques in DFIG-based wind turbines: a review

Offshore wind farms (OWFs) have received widespread attention for their abundant unexploited wind energy potential and convenient locations conditions. They are rapidly developing towards having large capacity and being located further away from shore. It is thus necessary to explore effective power transmission technologies to connect large OWFs to onshore grids. At present, three types of power transmission technologies have been proposed for large OWF integration. They are: high voltage alternating current (HVAC) transmission, high voltage direct current (HVDC) transmission, and low-frequency alternating current (LFAC) or fractional frequency alternating current transmission. This work undertakes a comprehensive review of grid connection technologies for large OWF integration. Compared with previous reviews, a more exhaustive summary is provided to elaborate HVAC, LFAC, and five HVDC topologies, consisting of line-commutated converter HVDC, voltage source converter HVDC, hybrid-HVDC, diode rectifier-based HVDC, and all DC transmission systems. The fault ride-through technologies of the grid connection schemes are also presented in detail to provide research references and guidelines for researchers. In addition, a comprehensive evaluation of the seven grid connection technologies for large OWFs is proposed based on eight specific indicators. Finally, eight conclusions and six perspectives are outlined for future research in integrating large OWFs.     

Hydrogen‐Assisted Growth of Ultrathin Te Flakes with Giant Gate‐Dependent Photoresponse

Tellurium (Te), as an elementary material, has attracted intense attention due to its potentially novel properties. However, it is still a great challenge to realize high‐quality 2D Te due to its helical chain structure. Here, ultrathin Te flakes (5 nm) are synthesized via hydrogen‐assisted chemical vapor deposition method. The density functional theory calculations and experiments confirm the growth mechanism, which can be ascribed to the formation of volatile intermediates increasing vapor pressure of the source and promoting the reaction. Impressively, the Te flake‐based transistor shows high on/off ratio ≈10⁴, ultralow off‐state current ≈8 × 10^?13 A, as well as a negligible hysteresis due to reducing thermally activated defects at 80 K. Moreover, Te‐flake‐based phototransistor demonstrates giant gate‐dependent photoresponse: when gate voltage varies from ?70 to 70 V, I_on/I_off is increased by ≈40‐fold. The hydrogen‐assisted strategy may provide a new approach for synthesizing other high quality 2D elementary materials.     

A DASH-based HEVC multi-view video streaming system

Recent advancement in cameras and image processing technology has generated a paradigm shift from traditional 2D and 3D video to multi-view video (MVV) technology, while at the same time improving video quality and compression through standards such as high efficiency video coding (HEVC). In multi-view, cameras are placed in predetermined positions to capture the video from various views. Delivering such views with high quality over the Internet is a challenging prospect, as MVV traffic is several times larger than traditional video, since it consists of multiple video sequences, each captured from a different angle, requiring more bandwidth than single-view video to transmit MVV. In addition, the Internet is known to be prone to packet loss, delay, and bandwidth variation, which adversely affect MVV transmission. Another challenge is that end users’ devices have different capabilities in terms of computing power, display, and access link capacity, requiring MVV to be adapted to each user’s context. In this paper, we propose an HEVC multi-view system using Dynamic Adaptive Streaming over HTTP to overcome the above-mentioned challenges. Our system uses an adaptive mechanism to adjust the video bit rate to the variations of bandwidth in best effort networks. We also propose a novel scalable way for the multi-view video and depth content for 3D video in terms of the number of transmitted views. Our objective measurements show that our method of transmitting MVV content can maximize the perceptual quality of virtual views after the rendering and hence increase the user’s quality of experience.