Development of a simple low-cost solar simulator for indoor collector testing

Indoor test methods for solar collectors are widely accepted and recommended by ASHRAE. The development of a solar simulator for indoor testing and the certification procedure for photo-thermal solar devices is discussed in this paper. The system consists of 14 quartz halogen lamps and provides a testing area of about 1 × 1 m. The irradiance can be varied from 400 to 1500 W/m². This is achieved by varying the input power supplied to individual lamps. The radiation output characteristics of a single lamp have been studied. The distribution of intensity over the covered area of 1·20 × 1·20 m has been recorded using a precision Eppley pyranometer.A variety of collectors—evacuated tubular collectors and flat-plate collectors of both liquid and air heating types—has been tested under sufficiently stable insolation conditions. Results for a conventional solar air heater are presented together with suggestions for further improvements.     

On connections between 3-d microstructures and their 2-d images

The problem of recovery of three-dimensional microstructural parameters from two-dimensional images is addressed in its inverse form. Three-dimensional inhomogeneous solids with known microstructures are generated virtually and images of their cross-sections are analyzed. Three different types of randomly oriented microcracks and microcracks having preferential orientation with some scatter. Somewhat unexpected result is that, in all the cases considered, three-dimensional defect densities are very close to average values of corresponding two-dimensional parameters.     

Quantification of carbon nanotube dispersion and its correlation with mechanical and thermal properties of epoxy nanocomposites

An experimental study is carried out to quantitatively assess the dispersion quality of carbon nanotubes (CNTs) in epoxy matrix as a function of CNT variant and weight fraction. To this end, two weight fractions (0.05% and 0.25%) of as-grown, oxidized, and functionalized CNTs are used to process CNT/epoxy nanocomposites. Scanning electron microscopy, X-ray diffraction, and Fourier transform infrared analysis of different variants of CNTs are used to establish the efficiency of purification route. While the relative change in mechanical properties is investigated through tensile and micro-hardness testing, thermal conductivity of different nanocomposites is measured to characterize the effect of CNT addition on the average thermal properties of epoxy. Later on, a quantitative analysis is carried out to establish the relationship between the observed improvements in average composite properties with the dispersion quality of CNTs in epoxy. It is shown that carboxylic (-COOH) functionalization reduces the average CNT agglomerate size and thus ensures better dispersion of CNTs in epoxy even at higher CNT weight fraction. The improved dispersion leads to enhanced interfacial interaction at the CNT/epoxy interface and hence provides higher relative improvement in nanocomposite properties compared to the samples prepared using as-grown and oxidized CNTs. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 48879.     

Chemopreventive Effect of Different Ratios of Fish Oil and Corn Oil in Experimental Colon Carcinogenesis

n-3 Polyunsaturated fatty acids (PUFA) have a chemopreventive effect while n-6 PUFA promote carcinogenesis. The effect of these essential fatty acids may be related to oxidative stress. Therefore, the study was designed to evaluate the effect of different ratios of fish oil (FO) and corn oil (CO) in the prevention of colon cancer. Male Wistar rats were divided into control, dimethylhydrazine dihydrochloride (DMH) treated, FO + CO (1:1) and FO + CO (2.5:1). All the groups, except the control received a weekly injection of DMH for 4 weeks. The animals were sacrificed either 48 h later (initiation phase) or kept for 16 weeks (post initiation phase). DMH treatment in the initiation phase animals showed mild to moderate inflammation, decreased ROS and TrxR activity, increased antioxidants, apoptosis and ACF multiplicity. The post initiation study showed severe inflammation with hyperplasia, increased ACF multiplicity and ROS levels, a decrease in antioxidants and apoptosis. The FO + CO (1:1) treated animals showed severe inflammation, a decrease in ROS, an increase in antioxidants and apoptosis in the initiation phase. FO + CO (1:1) in the post initiation phase and FO + CO (2.5:1) in the initiation showed mild inflammation, increased ROS, apoptosis and decreased antioxidants. There was a decrease in ACF multiplicity and ROS levels, increased antioxidants and apoptosis in the post initiation phase study. The present study suggests that FO has a dose- and time-dependent chemopreventive effect in colon cancer mediated through oxidative stress and apoptosis.     

Pressure induced order-disorder transition in a diblock copolymer

Polymers are known to undergo order↔order and order↔disorder transitions, when subjected to a change of pressure, temperature, solvent, pH of the medium etc. The molecular processes, which alter the volume of the system, are found to be highly sensitive to the pressure. In the present communication Zimm and Bragg model of helix↔coil transition has been modified to interpret the experimental data of pressure induced phase transition in polystyrene-polybutadiene [PS-PB] at different pressurization rates, as reported by Migler and Han, utilizing the Birefringence and small angle neutron scattering technique. An expression for the degree of order is obtained from the grand partition function for the entire chain in terms of nucleation parameter, which controls the transition width. The nucleation parameter σ increases with the increase in the ODT temperatures of the system. The phenomenon of hysteresis has been discussed in relation to the pressurization rate, which increases/decreases with the corresponding increase/decrease in the pressurization rate. The theoretical transition curves are found to be in good agreement with experimental data.     

Morphological changes associated with long-term potentiation

Long-term potentiation (LTP) is a long-lasting form of synaptic plasticity induced by brief repetitive afferent stimulation that is thought to be associated with learning and memory. It is most commonly studied in the hippocampus where it may last for several weeks, and involves the synthesis of new proteins that might play a structural role. In this review we summarize the evidence in favor of modifications of neuronal architecture during LTP. We focus our attention on changes occurring at the level of single synapses, including components of postsynaptic dendrites (dendritic spines, the postsynaptic density, and synaptic curvature), of presynaptic terminals, and the formation of new synapses. We conclude that although many morphological changes at various sites have been observed during LTP, there is no definitive proof in favor of structural changes associated with LTP. However, morphological modifications remain a valid candidate for mechanisms of learning and memory.     

Study of the effect of dilution on the lubricity of hydrotreated jet engine fuels

Hydrotreated fuels lack lubricity. Dilution with chemically treated conventional fuels is reported to restore lubricity. Studies revealed that some conventional fuels have lubricity inferior to the hydrotreated fuels. Thus dilution with conventional fuel is not a sure cure.     

Development of novel interpenetrating network gellan gum-poly(vinyl alcohol) hydrogel microspheres for the controlled release of carvedilol

Novel interpenetrating polymeric network microspheres of gellan gum and poly(vinyl alcohol) were prepared by the emulsion cross-linking method. Carvedilol, an antihypertensive drug, was successfully loaded into these microspheres prepared by changing the experimental variables such as ratio of gellan gum:poly(vinyl alcohol) and extent of cross-linking in order to optimize the process variables on drug encapsulation efficiency, release rates, size, and morphology of the microspheres. Formation of interpenetrating network and the chemical stability of carvedilol after preparing the microspheres was confirmed by Fourier transform infrared spectroscopy. Differential scanning calorimetry and x-ray diffraction studies were made on the drug-loaded microspheres to investigate the crystalline nature of the drug after encapsulation. Results indicated a crystalline dispersion of carvedilol in the polymer matrix. Scanning electron microscopy confirmed the spherical nature and smooth surface morphology of the microspheres produced. Mean particle size of the microspheres as measured by laser light scattering technique ranged between 230 and 346 µm. Carvedilol was successfully encapsulated up to 87% in the polymeric matrices. In vitro release studies were performed in the simulated gastric fluid or simulated intestinal fluid. The release of carvedilol was continued up to 12 h. Dynamic swelling studies were performed in the simulated gastric fluid or simulated intestinal fluid, and diffusion coefficients were calculated by considering the spherical geometry of the matrices. The release data were fitted to an empirical relation to estimate the transport parameters. The mechanical properties of interpenetrating polymeric networks prepared were investigated. Network parameters such as molar mass between cross-links and cross-linking density for interpenetrating polymeric networks were calculated.