Design of Smart Door Closer System with Image Classification over WLAN

Wireless Personal Communications - A dual purpose system is presented in this paper which serves not only as a door closer, but is equally effective for surveillance purposes. The currently...     

Multiply Charged Conjugated Polyelectrolytes as a Multifunctional Interlayer for Efficient and Scalable Perovskite Solar Cells

A series of anionic conjugated polyelectrolytes (CPEs) is synthesized based on poly(fluorene-co-phenylene) by varying the side-chain ionic density from two to six per repeat units (MPS2-TMA, MPS4-TMA, and MPS6-TMA). The effect of MPS2, 4, 6-TMA as interlayers on top of a hole-extraction layer of poly(bis(4-phenyl)-2,4,6-trimethylphenylamine (PTAA) is investigated in inverted perovskite solar cells (PeSCs). Owing to the improved wettability of perovskites on hydrophobic PTAA with the CPEs, the PeSCs with CPE interlayers demonstrate a significantly enhanced device performance, with negligible device-to-device dependence relative to the reference PeSC without CPEs. By increasing the ionic density in the MPS-TMA interlayers, the wetting, interfacial defect passivation, and crystal growth of the perovskites are significantly improved without increasing the series resistance of the PeSCs. In particular, the open-circuit voltage increases from 1.06 V for the PeSC with MPS2-TMA to 1.11 V for the PeSC with MPS6-TMA. The trap densities of the PeSCs with MPS2,4,6-TMA are further analyzed using frequency-dependent capacitance measurements. Finally, a large-area (1 cm²) PeSC is successfully fabricated with MPS6-TMA, showing a power conversion efficiency of 18.38% with negligible hysteresis and a stable power output under light soaking for 60 s.     

Flower‐shaped ultra‐wideband fractal antenna

A flower‐shaped ultra‐wideband fractal antenna is presented. It comprises a fourth iterative flower‐shaped radiator, asymmetrical stub‐loaded feeding line, and coplanar quarter elliptical ground planes. A wide operating band of 12.12 GHz (4.58‐16.7 GHz) for S ₁₁ ≤ ? 10 dB is achieved along with an overall antenna footprint of 15.7 × 11.4 mm². In addition, other desirable characteristics, that is, omnidirectional radiation patterns, peak gain upto 5 dB, and fidelity factor more than 75% are achieved. A good agreement exists between the simulation and measured results. The obtained results illustrate that this antenna has wide operating range and compact dimensions than available structures.     

Impact of adhesive ingredients on adhesion between rubber and brass-plated steel wire in tire

Proficiency on underlying mechanism of rubber-metal adhesion has been increased significantly in the last few decades. Researchers have investigated the effect of various ingredients, such as hexamethoxymethyl melamine, resorcinol, cobalt stearate, and silica, on rubber-metal interface. The role of each ingredient on rubber-metal interfacial adhesion is still a subject of scrutiny. In this article, a typical belt skim compound of truck radial tire is selected and the effect of each adhesive ingredient on adhesion strength is explored. Out of these ingredients, the effect of cobalt stearate is found noteworthy. It has improved adhesion strength by 12% (without aging) and by 11% (humid-aged), respectively, over control compound. For detailed understanding of the effect of cobalt stearate on adhesion, scanning electron microscopy and energy dispersive spectroscopy are utilized to ascertain the rubber coverage and distribution of elements. X-ray photoelectron spectroscopy results helped us to understand the impact of Cu_XS layer depth on rubber-metal adhesion. The depth profile of the Cu_XS layer was found to be one of the dominant factors of rubber-metal adhesion retention. Thus, this study has made an attempt to find the impact of different adhesive ingredients on the formation of Cu_XS layer depth at rubber-metal interface and establish a correlation with adhesion strength simultaneously.     

Mathematical model for computer simulation and control of steelmaking

A dynamic model for computer simulation and control of steelmaking has been developed. It is essentially based on multicomponent mixed transport control theory with the incorporation of energy balance calculations. The model is applicable to both steelmaking in electric furnaces as well as in oxygen steelmaking converters. The adjustable parameters of the model for simulation of oxygen steelmaking are gas evolution rate (G_co). oxygen flux factor (F_o) and emulsification factor (EM). These simulation parameters, when combined with on-line measurement of off-gas composition and temperature, enable complete dynamic control of the process. The model developed is applied, as an example, to an industrially produced heat in a top blown oxygen steelmaking converter and the results of simulation are discussed.     

Springback analysis of thin rectangular bars of non-linear work-hardening materials under torsional loading

A theoretical analysis of the springback of narrow rectangular strips of non-linear work-hardening material under torsional loading has been carried out. This theoretical analysis is supported by experimental results for rectangular mild steel strips of different thicknesses and lengths. Finally an analytical generalized expression relating angle of twist to twisting moment and residual angle of twist per unit length for rectangular strips under plastic torsion is obtained in non-dimensionalized form. A comparison between the results obtained for bars of non- linear and linear work-hardening materials loaded under torsion is also made.