Efficient Design of Bi-circular Patch Antenna for 5G Communication with Mathematical Calculations for Resonant Frequencies

Wireless Personal Communications - In this paper the conventional circular patch has been reshaped by two circular arcs with the FR4 Epoxy material for substrate. This is supported by the...     

Design of a wideband microstrip antenna and the use of artificial neural networks in parameter calculation

This paper deals with the design of a multi-slot hole-coupled microstrip antenna on a substrate of 2 mm thickness that gives multi-frequency (wideband) characteristics. The Method of Moments (MoM)-based IE3D software was used to simulate the results for return loss, VSWR, the Smith chart, and the radiation patterns. A tunnel-based artificial neural network (ANN) was also developed to calculate the radiation patterns of the antenna. The radiation patterns were measured experimentally at 10.5 GHz and 12 GHz. The experimental results were in good agreement with the simulated results from IE3D and those of the artificial neural network. A new method of using a genetic algorithm (GA) in an artificial neural network is also discussed. This new method was used to calculate the resonant frequency of a single-shorting-post microstrip antenna. The resonant frequency calculated using the genetic-algorithm-coupled artificial neural network was compared with the analytical and experimental results. The results obtained were in very good agreement with the experimental results.     

Numerical models of creep and boundary sliding mechanisms in single-phase, dual-phase, and fully lamellar titanium aluminide

Finite element simulations of the high-temperature behavior of single-phase γ, dual-phase α₂+γ, and fully lamellar (FL) α₂+γTiAl intermetallic alloy microstructures have been performed. Nonlinear viscous primary creep deformation is modeled in each phase based on published creep data. Models were also developed that incorporate grain boundary and lath boundary sliding in addition to the dislocation creep flow within each phase. Overall strain rates are compared to gain an understanding of the relative influence each of these localized deformation mechanisms has on the creep strength of the microstructures considered. Facet stress enhancement factors were also determined for the transverse grain facets in each model to examine the relative susceptibility to creep damage. The results indicate that a mechanism for unrestricted sliding of γ lath boundaries theorized by Hazzledine and co-workers leads to unrealistically high strain rates. However, the results also suggest that the greater creep strength observed experimentally for the lamellar microstructure is primarily due to inhibited former grain boundary sliding (GBS) in this microstructure compared to relatively unimpeded GBS in the equiaxed microstructures. The serrated nature of the former grain boundaries generally observed for lamellar TiAl alloys is consistent with this finding.     

Fast computation of multidimensional discrete Hartley transform

Efficient algorithms for the fast computation of 2D and 3D discrete Hartley transforms have been proposed. It is shown that the proposed algorithms offer a significant saving in computation over the existing methods for various array sizes.<>     

Thermal shock and thermal fatigue study of ceramic materials on a newly developed ascending thermal shock test equipment

A test equipment was designed to study thermal shock and thermal fatigue of ceramic materials subjected to fast heating (ascending). The equipment was designed to generate thermal stress in a test specimen by heating one surface of it by an oxy-hydrogen flame while cooling the opposite surface. The sample cracked when thermal stress exceeded its mechanical strength. The in situ crack formation was detected by an acoustic emission system coupled to the set up. The hot zone temperature was measured by an infra red pyrometer. The equipment was also designed to run thermal fatigue test cycles in automatic mode between two selected temperatures. The temperature and thermal stress distribution in the test specimen were modelled using finite element software. The effect of temperature distribution of the top and bottom surfaces on thermal stresses was studied. It was observed that the thermal stress is very sensitive to the temperature distribution on the top surface and maximum near the periphery of the top surface. This was in agreement with the experimental results in which the cracks were originated from the periphery of top surface. It was also observed that the failure temperature was higher for thicker samples.     

Synthesis of ductile titanium-titanium boride (Ti-TiB) composites with a beta-titanium matrix: The nature of TiB formation and composite properties

The study focused on the in-situ synthesis of titanium (Ti)-titanium boride (TiB) composites with β phase in the matrix by reaction sintering of TiB₂ with Ti and alloying element powders. The goal was to examine the nature of TiB whisker formation in three different kinds of powder mixtures: (1) β-Ti alloy powders and TiB₂; (2) α-Ti powder, a master alloy (Fe-Mo) powder containing the β-stabilizing elements, and TiB₂; and (3) α-Ti powder, a β-stabilizing elemental powder (Mo or Nb), and TiB₂. The effects of powder packing and the relative locations of powder particles on the morphological changes in TiB whisker formation and their growth were studied at processing temperatures ranging from 1100°C to 1300°C. The morphology, size, and distribution of whiskers were found to be influenced by the powder-packing conditions. A large particle-size ratio in bimodally packed mixtures led to the formation of a TiB monolithic layer around β grains. With a relatively finer starting powder, smaller size ratio, and trimodal packing arrangement, the TiB whiskers were found to be distributed more homogeneously in the matrix. The study also used the X-ray direct comparison method and the structure factor for the β phase to determine the volume fraction of TiB phase from X-ray data. Tensile tests and fractographic investigations were carried out on selected composites. The evolution of the composite microstructure, the influence of powder-packing variables, and the morphology and growth of TiB whiskers and their effect on mechanical properties are discussed.     

An automated, parallel processing approach to biomolecular sample preparation

Sample preparation for DNA and RNA assays is a prime candidate for laboratory automation. A novel, parallel processing device that performs the three separate liquid-handling functions necessary for such sample preparation-dispensing, pipetting, and pressurizing-is presented. The device comprises an array of fine nozzles connected by fluidic channels to automatically and precisely distribute flow between one source and an array of points. The design principles, as well as the experimental and computational methods used to develop the device, are described. Test results, including accuracy, uniformity, volume range, and timing, are presented. The functionality of the device is demonstrated by performing a solid-phase extraction of DNA with two types of microcolumns.     

A novel sine augmented scaled sine cosine algorithm for frequency control issues of a hybrid distributed two-area power system

Neural Computing and Applications - In this research article, a novel approach is proposed by considering the sine augmented scaled sine cosine (SAS-SCA) Algorithm for the load frequency control of...