Temperature characterization of flip-chip packaged piezoresistive barometric pressure sensors

In order to miniaturize piezoresistive barometric pressure sensors, a new flip-chip packaging technology has been developed. The thermal expansions of chip and package are different. So in a standard flip-chip package the strong mechanical coupling by the solder bumps would lead to stress in the sensor chip, which is unacceptable for piezoresistive pressure sensors. To solve this problem, in the new packaging technology the chip is flip-chip bonded on compliant springs to decouple chip and package. As the first step of the packaging process an under bump metallization (UBM) is patterned on the sensor wafer. Then solder bumps are printed. After wafer-dicing the chips are flip-chip bonded on copper springs within a ceramic cavity housing. Due to the compliance of the springs, packaging stress is induced into the sensor chip. As sources of residual stress the UBM and the solder bumps on the sensor chip were identified. Different coefficients of thermal expansion of the silicon chip, the UBM and the solder lead to plastic straining of the aluminum metallization between UBM and chip. As a consequence the measurement accuracy is limited by a temperature hysteresis. The influence of the chip geometry, e.g., the thickness of the chip or the depth of the cavity, on the hysteresis was investigated by simulation and measurements. As a result of this investigation a sensor chip was designed with very low residual stress and a temperature hysteresis which is only slightly larger than the noise of the sensor.     

Damage phenomena in lubricated rolling-sliding wear of a gas carburised 0.85%Mo low-alloyed sintered steel: theoretical analysis and experimental verification

The resistance to surface and subsurface damage during lubricated rolling-sliding wear of a carburised low-alloy sintered steel and the effect of shot peening were investigated. The formation of both contact fatigue cracks and of brittle tensile cracks may be predicted by a theoretical model that was experimentally validated. Carburising is effective in increasing the resistance to contact fatigue, but pores in a hard and brittle matrix may act as pre-existing cracks. Shot peening increases the contact fatigue resistance since compressive residual stresses oppose the nucleation of surface cracks.     

Rumination activity of dairy cows in the 24 hours before and after calving

Monitoring rumination behavior serves multiple purposes in feeding and herd management of dairy cows. The process of calving is a major event for cows, and a detailed understanding of alterations in behavioral patterns of animals in the time around calving is important in calving detection. The objective of this study was to describe the short-term changes in rumination patterns in dairy cows immediately before and after parturition. In total, 17 cows were fitted with rumination sensors that were able to monitor rumination time, number of rumination boli, and number of rumination jaw movements. Rumination time was decreased in the last 4 h antepartum and in the first 8 h postpartum. Cows stopped ruminating 123 ± 58 min (mean ± standard deviation) before calving and resumed ruminating 355 ± 194 min after calving. The number of rumination jaw movements and boli per day were decreased in the 24-h period postpartum. Rumination rate, the number of rumination jaw movements per rumination minute, and the number of boli per rumination minute changed little around calving. The calving event primarily influenced the duration and frequency of various rumination characteristics but not rumination intensity. Among detected characteristics, rumination time showed the greatest potential for monitoring of calving events.     

Heterotrophic growth and nutritional aspects of the diatom Cyclotella cryptica (Bacillariophyceae): Effect of some environmental factors

To investigate the nutritional value of the diatom Cyclotella cryptica (Reimann, Lewin, and Guillard) as an alternative feed for use in the aquaculture industry, the heterotrophic growth characteristics and resultant fatty acid profile of the microalga were studied when cultivated under a variety of controlled salinity and temperature conditions. In addition, the effects of pH on the growth characteristics were also studied. The maximum specific growth rate was affected by initial pH and cultivation temperature, but not by salinity. The optimal pH and temperature ranges for growth were 7.2 to 8.1 and 22.5 to 25.0 °C, respectively. Lipid accumulation and the fatty acid composition were also affected by cultivation temperature and salinity. The optimal temperature range and salinity level for lipid accumulation were 18.0 to 25.0 °C and 11.2 psu, respectively. In all cases the fatty acid distribution was similar, with the most abundant fatty acids being palmitic acid (16:0), palmitoleic acid (16:1 n-7), stearidonic acid (18:4 n-3, SDA), eicosapentaenoic acid (20:5 n-3, EPA), and decosahexaenoic acid (22:6 n-3, DHA).     

计算多轴拌器的轴功率

对三种搅拌器：锚式、螺旋式、锯齿式，在不同的转速配比下进行了轴功率测试，搅拌雷诺数为０．８～３０００００，液体的粘度为０．００１～８４Ｐａ．ｓ。液体的性质属牛顿型流体，试验过程用计算机控制．通过测量轴的扭矩来确定搅拌器的轴功率。实验测定了不同情况下搅拌器相互之间的影响。实验数据由马跨特计算方法确定模型参数并给出层流至湍流范围内三种搅拌器轴功率的计算公式．     

Relationship between age and risk taking among managers.

Administered a short version of N. Kogan and M. Wallach's (see pa, vol. 39:6826) choice-dilemma test to 1,484 managers from over 200 companies. Results show a significant negative relationship between age and both risk taking and the value placed upon risk. The relationships were small in size when individual scores were correlated with age, but increased markedly when mean scores were used. Furthermore, the relationships were relatively stable across items and across companies. Developmental and sociocultural mechanisms that might underlie these findings are discussed. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Evaluating the scope for energy-efficiency improvements in the public sector: Benchmarking NHSScotland's smaller health buildings

The National Health Service in Scotland (NHSScotland) has, in recent years, done much to reduce energy consumption in its major healthcare buildings (hospitals). On average, a reduction of 2% per year has been achieved since 2000, based on hospital buildings. However, there had been little or no attention paid to smaller premises such as health centres, clinics, dentists, etc. Such smaller healthcare buildings in Scotland constitute 29% of the total treated floor area of all NHSScotland buildings and, therefore, may contribute a similar percentage of carbon and other emissions to the environment. By concentrating on a sample of local health centres in Scotland, this paper outlines the creation of an energy benchmark target, which is part of a wider research project to investigate the environmental impacts of small healthcare buildings in Scotland and the scope for improvements. It was found that energy consumption varied widely between different centres but this variation could not be linked to building style, floor area or volume. Overall, it was found that a benchmark of 0.2 GJ/m³ would be challenging, but realistic.