Deduction of a facile method to construct Antheraea mylitta silk fibroin/gelatin blend films for prospective biomedical applications

Blend films of two types (I and II) were prepared by mixing Antheraea mylitta silk fibroin (AMF) and gelatin solution in various blend ratios via the solution casting method. Two different crosslinkers, namely glutaraldehyde and genipin, were used during blend preparation. The structural characteristics and thermal properties of the blend films were examined by Fourier transform infrared (FTIR) spectroscopy, X‐ray diffraction (XRD), Thermogravimetric analysis (TGA) and Diffrential scanning calorimetery (DSC). The FTIR spectra showed conformational alterations in type I blend films while type II films attained high β‐sheet crystallinity. The XRD diffractograms presented a high degree of crystallinity in type II blend films compared to type I, which showed an almost amorphous structure. Further, thermal and biological studies were conducted on type II films. According to the TGA thermograms, the degradation temperature of the crosslinked blend films shifted compared to pure gelatin and pure AMF films. Partial miscibility of the two components was indicated by DSC thermograms of the blends. The high water uptake capacity of type II blend films was found to imitate hydrogel behaviour. The blend films did not show any toxicity in 3‐(4,5‐dimethylthiazol‐2‐yl)‐2,5‐diphenyl tetrazolium bromide (MTT) assay and supported L929 fibroblast cell spreading and proliferation. The biodegradation of the blend films was significantly faster than the pure silk film. © 2020 Society of Industrial Chemistry     

Interface cracking between functionally graded coatings and a substrate under antiplane shear

Coating technology plays a significant role in a number of applications such as high temperatures, corrosion, oxidation, wear, and interface. In this paper, we investigate the interface cracking between ceramic and/or functionally graded coatings (FGM coatings) and a substrate under antiplane shear. Four coating models are considered, namely single layered homogeneous coating, double layered piece-wise homogeneous coating, single layered FGM coating and double layered coating with an FGM bottom coat. Mode III stress intensity factors (SIFs) are calculated for the different coating models. In the case of μ_L > μ₀ where μ₀ is the shear modulus of the substrate and μ_L the shear modulus of the material at the surface of the coating, it is found that the single layered FGM coating reduces SIF slightly, whereas the coating system with a top homogeneous layer and a thin FGM bottom layer reduces SIF significantly. In the case of μ_L < μ₀ the SIF is found to be larger for the FGM coatings than for the homogeneous coatings. The FGM coating, however, may still be superior to homogeneous coatings in this case as FGM coatings usually provide better bonding strength between the coating and substrate. Finally, the applicability of the SIF concept in the fracture of FGM coatings is discussed. Large modulus gradients in thin coatings may seriously restrict the application of SIFs as the SIF-dominant zone may fall into the crack tip nonlinear deformation and damage zone. The same argument exists for some interphase models in interface crack solutions.     

Deposition of thin film silicon using the pulsed PECVD and HWCVD techniques

We report on the use of pulsed plasma-enhanced chemical vapor deposition (P-PECVD) technique and show that “state-of-the-art” amorphous silicon (a-Si:H) materials and solar cells can be produced at a deposition rate of up to 15 Å/s using a modulation frequency in the range 1–100 kHz. The approach has also been developed to deposit materials and devices onto large area, 30 cm×40 cm, substrates with thickness uniformity (<5%), and gas utilization rate (>25%). We have developed a new “hot wire” chemical vapor deposition (HWCVD) method and report that our new filament material, graphite, has so far shown no appreciable degradation even after deposition of 500 μm of amorphous silicon. We report that this technique can produce “state-of-the-art” a-Si:H and that a solar cell of p/i/n configuration exhibited an initial efficiency approaching 9%. The use of microcrystalline silicon (μc-Si) materials to produce low-cost stable solar cells is gaining considerable attention. We show that both of these techniques can produce thin film μc-Si, dependent on process conditions, with 1 1 1 and/or 2 2 0 orientations and with a grain size of approx. 500 A. Inclusion of these types of materials into a solar cell configuration will be discussed.     

Resource contention in shared-memory multiprocessors: A parameterized performance degradation model

A standard metric conventionally employed to compare the performance of different multiprocessor systems is speedup. Although providing a measure of the improvement in execution speed achievable on a system, this metric does not yield any insight into the factors responsible for limiting the potential improvement in speed. This paper studies the performance degradation in shared-memory multiprocessors as a result of contention for shared-memory resources. A replicate workload framework with a flexible mechanism for workload specification is proposed for measuring performance. Two normalized performance metrics—efficiency and overhead factor—are introduced to quantify the factors limiting performance and facilitate comparison across architectures. Finally, the proposed model is employed to measure and compare the performance of three contemporary shared-memory systems, with special emphasis on the newly released BBN Butterfly-II (TC2000), currently undergoing Beta test.     

Haemangiopericytoma of the nasal cavity

Haemangiopericytoma of nose and paranasal sinuses is relatively uncommon tumour. It occurs in adults in sixth and seventh decades of life. In view of paucity of intranasal haemangiopericytoma old in Indian literature and young age of patient, we are reporting one case in 28-year-old female who presented with recurrent, profuse epistaxis.     

INFLUENCE OF DRYING CONDITIONS ON THE FRAGILITY OF CORN KERNELS

A dynamic rcsring dnim war built to study the effects of air temperature, moisture content and grain shape on fragility of the air dried kernels. For drying rares under 0.05 kglkg min. the fragility of kernels could br described empirically as a function of the three experimental parameters.