A 0.25-/spl mu/m CMOS quad-band GSM RF transceiver using an efficient LO frequency plan

This paper describes a single-chip CMOS quad-band (850/900/1800/1900 MHz) RF transceiver for GSM/GPRS applications. It is the most important design issue to maximize resource sharing and reuse in designing the multiband transceivers. In particular, reducing the number of voltage-controlled oscillators (VCOs) required for local oscillator (LO) frequency generation is very important because the VCO and phase-locked loop (PLL) circuits occupy a relatively large area. We propose a quad-band GSM transceiver architecture that employs a direct conversion receiver and an offset PLL transmitter, which requires only one VCO/PLL to generate LO signals by using an efficient LO frequency plan. In the receive path, four separate LNAs are used for each band, and two down-conversion mixers are used, one for the low bands (850/900 MHz) and the other for the high bands (1800/1900 MHz). A receiver baseband circuit is shared for all four bands because all of their channel spaces are the same. In the transmit path, most of the building blocks of the offset PLL, including a TX VCO and IF filters, are integrated. The quad-band GSM transceiver that was implemented in 0.25-/spl mu/m CMOS technology has a size of 3.3/spl times/3.2 mm/sup 2/, including its pad area. From the experimental results, we found that the receiver provides a maximum noise figure of 2.9 dB and a minimum IIP3 of -13.2dBm for the EGSM 900 band. The transmitter shows an rms phase error of 1.4/spl deg/ and meets the GSM spectral mask specification. The prototype chip consumes 56 and 58 mA at 2.8 V in the RX and TX modes, respectively.     

Reversible energy recovery logic circuit without non-adiabaticenergy loss

The authors propose a reversible energy recovery logic (RERL) circuit for ultra-low-energy consumption, which consumes only adiabatic energy loss and leakage current loss by completely eliminating non-adiabatic energy loss. It is a dual-rail adiabatic circuit using the concept of reversible logic with a new eight-phase clocking scheme. Simulation results show that at low-speed operation, the RERL consumes much less energy than the complementary static CMOS circuit and other adiabatic logic circuits     

Exact controllability for semilinear parabolic equations with Neumann boundary conditions

This paper studies the problem of exact boundary controllability of second-order semilinear parabolic equations when the control is under Neumann's boundary conditions. For a nonlinear term with a sublinear growth we prove the global null-controllability and for the superlinear growth case we prove the local exact controllability of the equations.     

Highly Cooperative Tetrametallic Ruthenium-mu-Oxo-mu-Hydroxo Catalyst for the Alcohol Oxidation Reaction

The tetrametallic ruthenium-oxo-hydroxo-hydride complex {[(PCy(3))(CO)RuH](4)(mu(4)-O)(mu(3)-OH)(mu(2)-OH)} (1) was synthesized in two steps from the monomeric complex (PCy(3))(CO)RuHCl (2). The tetrameric complex 1 was found to be a highly effective catalyst for the transfer dehydrogenation of alcohols. Complex 1 showed a different catalytic activity pattern towards primary and secondary benzyl alcohols, as indicated by the Hammett correlation for the oxidation reaction of p-X-C(6)H(4)CH(2)OH (rho = -0.45) and p-X-C(6)H(4)CH(OH)CH(3) (rho = +0.22) (X = OMe, CH(3), H, Cl, CF(3)). Both a sigmoidal curve from the plot of initial rate vs [PhCH(OH)CH(3)] (K(0.5) = 0.34 M; Hill coefficient, n = 4.2+/-0.1) and the phosphine inhibition kinetics revealed the highly cooperative nature of the complex for the oxidation of secondary alcohols.     

Improved mechanical properties of shape‐memory polyurethane block copolymers through the control of the soft‐segment arrangement

High‐performance shape‐memory polyurethane block copolymers, prepared with two types of poly(tetramethylene glycol) (PTMG) used as soft segments, were investigated for their mechanical properties. Copolymers with a random or block soft‐segment arrangement had higher stresses at break and elongations at break than those with only one kind of PTMG. Random copolymers with fewer interchain interactions showed higher elongation than block copolymers. All the copolymers had shape‐recovery ratios higher than 80%. In dynamic mechanical testing, the glass‐transition behavior clearly depended on the soft‐segment arrangement: random copolymers had only one glass‐transition peak, whereas block copolymers showed two separate glass‐transition peaks. Overall, the control of the soft‐segment arrangement plays a vital role in the development of high‐performance shape‐memory polyurethane. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 2410–2415, 2004     

Improvement of cyclodextrin glucanotransferase as an antistaling enzyme by error-prone PCR

In an effort to improve the properties of cyclodextrin glucanotransferase (CGTase) as an antistaling enzyme, error-prone PCR was used to introduce random mutations into a CGTase cloned from alkalophilic Bacillus sp. I-5 (CGTase I-5). A mutant CGTase[3-18] with the three mutations M234T, F259I and V591A was selected by agar plate assay. Sequence alignment of various CGTases indicated that M234 and F259 are located in the vicinity of the catalytic sites of the enzyme and V591 in the starch binding domain E. The cyclization activity of CGTase[3-18] was dramatically decreased by 10-fold, while the hydrolyzing activity was increased by up to 15-fold. These mutations near subsite +1 (M234T) and at subsite +2 (F259I) are likely to alter the enzyme activity in a concerted manner, promoting hydrolysis of substrate while retarding cyclization. The addition of CGTase[3-18] reduced the retrogradation rate of bread by as much as did the commercial antistaling enzyme Novamyl during 7-day storage at 4 degrees C. No cyclodextrin (CD) was detected in bread treated with CGTase[3-18], whereas 21 mg of CD per 10 g of bread was produced in bread treated with wild-type CGTase.     

Synthesis and physicochemical characterization of amphiphilic block copolymer self‐aggregates formed by poly(ethylene glycol)‐block‐poly(ϵ‐caprolactone)

Diblock copolymers with different poly(ε‐caprolactone) (PCL) block lengths were synthesized by ring‐opening polymerization of ε‐caprolactone in the presence of monomethoxy poly(ethylene glycol) (mPEG‐OH, MW 2000) as initiator. The self‐aggregation behaviors and microscopic characteristics of the diblock copolymer self‐aggregates, prepared by the diafiltration method, were investigated by using ¹H NMR, dynamic light scattering (DLS), and fluorescence spectroscopy. The PEG–PCL block copolymers formed the self‐aggregate in an aqueous environment by intra‐ and/or intermolecular association between hydrophobic PCL chains. The critical aggregation concentrations of the block copolymer self‐aggregate became lower with increasing hydrophobic PCL block length. On the other hand, reverse trends of mean hydrodynamic diameters were measured by DLS owing to the increasing bulkiness of the hydrophobic chains and hydrophobic interaction between the PCL microdomains. The partition equilibrium constants (K_v) of pyrene, measured by fluorescence spectroscopy, revealed that the inner core hydrophobicity of the nanoparticles increased with increasing PCL chain length. The aggregation number of PCL chain per one hydrophobic microdomain, investigated by the fluorescence quenching method using cetylpyridinium chloride as a quencher, revealed that 4–20 block copolymer chains were needed to form a hydrophobic microdomain, depending on PCL block length. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 99: 3520–3527, 2006     

DCT statistics-based digital dropout detection in degraded archived media

With the rapid development of visual digital media, the demand for better quality of service has increased the pressure on broadcasters to automate their error detection and restoration activities for preserving their archives. Digital dropout is one of the defects that affect archived visual materials and tends to occur in block by block basis (size of 8 × 8). It is well established that human visual system (HVS) is highly adapted to the statistics of its visual natural environment. Consequently, in this paper, we have formulated digital dropout detection as a classification problem which predicts block label based on statistical features. These statistical features are indicative of perceptual quality relevant to human visual perception, and allow pristine images to be distinguished from distorted ones. Here, the idea is to extract discriminant block statistical features based on discrete cosine transform (DCT) coefficients and determine an optimal neighborhood sampling strategy to enhance the discrimination ability of block representation. Since this spatial frame based approach is free from any motion computation dependency, it works perfectly in the presence of fast moving objects. Experiments are performed on video archives to evaluate the efficacy of the proposed technique.     

Electron‐beam deposition of MgO on plastic substrate and manufacturing flexible flat fluorescent lamp

Abstract— A flexible fluorescent lamp that utilizes the same plasma discharge mode as in PDPs has been manufactured. The structure of the flexible lamp is simple and easy to manufacture. All‐plastic materials including plastic substrates, barrier ribs (spacers), and sealants for low‐temperature manufacturing processing have been adopted except for the phosphor and MgO thin film. The MgO thin films were coated on the plastic substrates as a protection layer against the plasma discharge. The adhesion and biaxial texture of MgO thin film deposited on the plastic substrates, poly‐ethyle‐nenaphthalate (PEN) and polycarbonate (PC), at low temperature (100–180°C) has been characterized. The MgO film on PEN shows good adhesion under a repeated bending test. The manufactured flexible lamp consists of two plastic substrates of about 3 in. on the diagonal, barrier rib (spacer), and external ITO electrodes. The Ne‐Xe (5%) gas mixture at 100–200 Torr was used for the discharge gas. A maximum surface luminance of about 100 cd/m² was achieved for a 1 ‐kHz AC pulse.     

Robust background maintenance by estimating global intensity level changes for dynamic scenes

The maintenance of relevant backgrounds under various scene changes is very crucial to detect foregrounds robustly. We propose a background maintenance method for dynamic scenes including global intensity level changes caused by changes of illumination conditions and camera settings. If the global level of the intensity changes abruptly, the conventional background models cannot discriminate true foreground pixels from the background. The proposed method adaptively modifies the background model by estimating the level changes. Because there are changes caused by moving objects as well as global intensity level changes, we estimate the dominant level change over the whole image regions by mean shift. Then, the problem caused by saturated pixels are handled by an additional scheme. In the experiments for dynamic scenes, our proposed method outperforms previous methods by adaptive background maintenance and handling of saturated pixels.