Glass Additive Influence on the Sintering Behaviors,Magnetic and Electric Properties of Bi–Zn Co‐Doped Co2Y Ferrites

The Bi₂O₃–B₂O₃–ZnO–SiO₂ (BB35SZ) glass effects on the sintering behavior and magnetic properties of Bi–Zn co‐doped Co₂Y ferrites were investigated in developing low‐temperature‐fired ferrites. The results indicate that BB35SZ glass can be used as a sintering aid to reduce the densification temperature of Co₂Y ferrites from 1300°C to 900°C. The 2(Ba_0.9Bi_0.1O)·2(Zn_0.4Co_0.4Cu_0.2O)·6(Fe_1.97Zn_0.03O₃) ferrite with 4 wt% BB35SZ glass can be densified below 900°C, exhibiting an initial permeability of 3.4 and quality factor of 55. This process provides a promising candidate for multilayer chip magnetic devices for microwave applications.     

Effect of Ru addition on the properties of Al-doped ZnO thin films prepared by radio frequency magnetron sputtering on polyethylene terephthalate substrate

The addition of ruthenium in aluminum-doped zinc oxide transparent conducting thin films was deposited on polyethylene terephthalate at 20 °C by radio frequency magnetron sputtering technique. The structure and electrical properties of the films were investigated with respect to variation of Ru concentration. The XRD and FESEM results show that the film with 0.5 wt% Ru doping has the best crystallinity and larger pyramid-like grains, therefore the resistivity reached to a lowest value of 9.1 × 10⁻⁴ Ωcm. The low carrier mobilities of the films (3–7.2 cm² V⁻¹ s⁻¹), however, were limited by ionized impurity scattering and grain boundary scattering mechanisms since the carrier concentrations were ranged from 2.2 × 10²⁰ to 9.5 × 10²⁰ cm⁻³. The transmittance in the visible is greater than 80% with the optical band gap in the order of 3.352–3.391 eV.     

非均匀不稳定表面粗糙目标的太赫兹波段散射特性分析

研究了不同粗糙度的非均匀不稳定表面粗糙导体目标在太赫兹波段的散射特性,区别于采用经验公式的建模方法,提出把随机粗糙面的建模理念应用到太赫兹波段的非均匀不稳定表面粗糙目标的建模中,用描述随机粗糙面的均方根高度(h)和相关长度(l)两个物理量来调节目标表面的粗糙度变化.首先用高斯随机粗糙面模拟非均匀不稳定粗糙目标的表面,然后采用物理光学和等效电流相结合的方法进行仿真计算,分别对不同入射角、不同频率和不同粗糙度的不同非均匀不稳定表面粗糙导体目标,在太赫兹波段散射特性进行了分析,最后得出相关的结论.     

The signaling efficiency of group mobility management in Cellular IP

Grouping is usually beneficial from a system efficiency perspective, e.g., trunking efficiency achieved by sharing a common channel among users. In this article, the signaling cost of mobility management in Cellular IP is numerically analyzed. In addition, it is shown analytically that by organizing mobile hosts having the same mobility pattern into a group, the signaling cost of mobility management in Cellular IP can be effectively reduced. This is because location information of the group can often be refreshed by data packets sent by group members. As a result, the reduction is more significant for a larger number of busy mobile hosts in the group.     

A seamless handoff scheme for IEEE 802.11 wireless networks

The advance of computer network technologies such as IEEE 802.11 wireless local area network has made it possible for users to connect to Internet almost anywhere. A mobile node (MN) is likely to move between different base stations while running applications. The IETF has defined the Mobile IP (MIP) to allow MNs to maintain their communication uninterrupted while roaming across different IP subnets. However, the mechanisms defined in MIP may cause undesired connection disruptions or packet losses, which will significantly degrade the quality of real‐time applications. It is an important and challenging issue to support seamless handoff management. To achieve seamless handoff, we propose a unified scheme to address application quality degradation. Our main contribution is the concept and implementation of utilising buffering and resending method to eliminate the packet losses while keeping the end‐to‐end delay of real‐time traffic flow in an acceptable value. The NS‐2 simulation results show that our proposed scheme can significantly maintain application quality during layer‐2 and ‐3 handoffs. Copyright © 2011 John Wiley & Sons, Ltd.     

Adding sense of spatial locality to routing protocols for mobile ad hoc networks

Recently, there has been an increasing interest in mobile ad hoc networks. In a mobile ad hoc network, each mobile node can freely move around and the network is dynamically constructed by collections of mobile nodes without using any existing network infrastructure. Compared to static networks, it faces many problems such as the inefficiency of routing algorithms. Also, the number of control packets in any routing algorithm increases as the mobile speed or the number of mobile nodes increases. Most of the current routing protocols in ad hoc networks broadcast the control packets to the entire network. Therefore, by reducing the number of control packets, the efficiency of the network routing will be improved. If we know where the destination is, we can beam our search toward that direction. However, without using global positioning systems, how can we do this? Define the range nodes as the 1‐hop or 2‐hop neighbors of the destination node. In this paper, we propose using the range nodes to direct our searches for the destination. It can be combined with the existing routing protocols to reduce the control overhead. We show through simulations that AODV and DSR combined with the range node method outperforms the original AODV and DSR routing protocols in terms of control packets overhead. We also show that the delay introduced in find range nodes is insignificant. Copyright © 2006 John Wiley & Sons, Ltd.     

Production of hydrogen and light hydrocarbons as a potential gaseous fuel from microwave-heated pyrolysis of waste automotive engine oil

Waste automotive engine oil was pyrolyzed in a continuous stirred bed reactor using microwave energy as the heat source; the yield and characteristics of the incondensable gaseous products are discussed. The recovered gases (41 wt% yield) were found to contain substantial concentrations of light aliphatic hydrocarbons (up to 86 vol.%) that could potentially be used as a chemical feedstock or a fuel source to power the process, or to be reformed to produce hydrogen for use as a second-generation fuel. Examination of the composition of the gases also showed the formation of H₂ (up to 19 vol.%) and CO that could also be used as a valuable syngas (with a H₂ + CO content of up to 35 vol.%). The high yield of gaseous hydrocarbons can be attributed to the unique heating mode and chemical environment present during microwave-heated pyrolysis. The use of a microwave-heated bed of particulate-carbon showed advantages in transforming waste oil into valuable gases. Hence an environmentally unfriendly waste material can be transformed into a useful resource and serves as an alternative source of hydrogen or hydrocarbon energy. The recovery of valuable gases shows advantage over traditional destructive approaches and suggests excellent potential for recycling problematic waste oil.     

Combustion and emission performances of coconut,palm and soybean methyl esters under reacting spray flame conditions

The spray combustion characteristics of coconut (CME), palm (PME) and soybean (SME) biodiesels/methyl esters were compared with diesel by using an axial swirl flame burner. Atomisation of the liquid fuels was achieved via an airblast-type nozzle with varied atomising air-to-liquid ratios (ALR) of 2–2.5. The fully developed sprays were mixed with strongly swirled air to form combustible mixtures prior to igniting at the burner outlet. Under fuel-lean condition, biodiesel spray flames exhibited bluish flame core without the yellowish sooty flame brush, indicating low sooting tendency as compared to baseline diesel. Increasing the atomising air led to the reduction of flame length but increase in flame intensity. Measurements of post-combustion emissions show that SME produced higher NO as compared to CME and PME due to higher degree of unsaturation, while the most saturated CME showed the lowest NO and CO emissions amongst the biodiesels tested across all equivalence ratios. By preheating the main swirl air to 250 °C, higher emissions of NO, CO and CO₂ were observed for biodiesels. Higher ALR led to reduced NO and CO emissions regardless of the fuel used, making it a viable strategy to resolve the simultaneous NOCO reduction conundrum. This work shows that despite different emission characteristics exhibited by biodiesels produced from different feedstock, they are in principle potential supplemental fuels for practical combustion systems. The pollutants emitted can be mitigated by operating at higher ALR in a twin-fluid based swirl combustor.     

Synthesis and properties of TLCPs with 2,6‐naphthalene‐based mesogen,polymethylene spacer,and nonlinear 4,4′‐thiodiphenyl links

A series of new thermotropic main‐chain liquid crystalline copolyesters were prepared by polycondensation of 2,6‐naphthalenedicarbonyl chloride, 4,4′‐thiodiphenol, and α,ω‐alkanediols (n = 4–10) in diphenyl ether at 200°C. Thermal transition behaviors of these copolyesters were investigated by differential scanning calorimetry. Moreover, their thermal stabilities and mesomorphic textures were studied by thermogravimetric analysis and polarizing optical microscopy, respectively. Corresponding model compounds with terminal mesogenic units and central polymethylene spacers were also synthesized for comparison. Both copolymers and model compounds exhibit odd–even dependency of melting temperatures, transition enthalpy (ΔH_m), and entropy (ΔS_m) on the number of methylene units in the spacer. However, the odd–even effects in model compounds are much more distinctive. Nematic mesophases are the only texture observed in melts, except the model compounds with longer methylene units (n = 8, 10), in which smectic mesophases can be observed. The T_m values of the copolyesters (TDP/HD = 1/1) are between 233 and 259°C, depending on spacer length. The initial decomposition temperatures of the copolyesters are above 419°C under N₂ atmosphere. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 1536–1546, 2002